Airlink101 AR325W User manual

Brand: Airlink101

Model: AR325W

Category: WLAN access points

Type: User manual

802.11g Wireless Router

Model # AR325W

User’s Manual

Ver. 1A

Table of Contents

1. Introduction .................................................................................................................3

1.1 Functions and Features.........................................................................................3

2. Hardware Installation...................................................................................................5

2.1 Connect the Router................................................................................................5

2.2 Verify Connection to Router...................................................................................6

3. Configure the Router...................................................................................................9

3.1 Setup Wizard.........................................................................................................9

4. Verify Connection Status and Wireless Settings.......................................................13

4.1 Checking the System Status................................................................................13

4.2 Connecting to the Router Wirelessly....................................................................14

5. Web Configuration.....................................................................................................15

5.1 Accessing the Web Configuration Utility..............................................................15

5.2 Basic Setting........................................................................................................16

5.2.1 Primary Setup ...............................................................................................16

5.2.2 DHCP Server ................................................................................................21

5.2.3 Wireless ........................................................................................................22

5.2.4 Change Password.........................................................................................25

5.3 Forwarding Rules.................................................................................................26

5.3.1 Virtual Server ................................................................................................26

5.3.2 Special AP.....................................................................................................27

5.3.3 Miscellaneous ...............................................................................................28

5.4 Security Setting....................................................................................................29

5.4.1 Packet Filter..................................................................................................29

5.4.2 Domain Filter.................................................................................................31

5.4.3 URL Blocking ................................................................................................32

5.4.4 MAC Address Control ...................................................................................33

5.4.5 Miscellaneous Items......................................................................................34

5.5 Advanced Settings...............................................................................................35

5.5.1 System Time.................................................................................................35

5.5.2 System Log...................................................................................................36

5.5.3 Dynamic DNS................................................................................................37

5.5.4 SNMP............................................................................................................38

5.5.5 Routing..........................................................................................................39

5.5.6 Schedule Rule...............................................................................................40

5.6 Toolbox................................................................................................................42

5.6.1 View Log .......................................................................................................42

5.6.2 Firmware Upgrade ........................................................................................43

5.6.3 Backup Setting..............................................................................................44

5.6.4 Reset to Default ............................................................................................44

5.6.5 Reboot ..........................................................................................................44

5.6.6 Miscellaneous Items......................................................................................45

6. Troubleshooting.........................................................................................................45

Appendix.......................................................................................................................47

1. Introduction

Congratulations on your purchase of this 802.11g Wireless Router. This product is

specifically designed for Small Office and Home Office needs. It provides a complete

SOHO solution for Internet surfing and is easy to configure and operate even for non-

technical users. Instructions for installing and configuring this product can be found in

this manual. Before you install and use this product, please read this manual carefully

for proper operation of this product.

1.1 Functions and Features

Basic Functions

• NAT Routing

Connects multiple computers to a broadband (cable or DSL) modem or an

Ethernet router to surf the Internet.

• Auto-Sensing Ethernet Switch

Equipped with a 4-port auto-sensing Ethernet switch.

• WAN Types supported

The router supports the following WAN types: Static IP, Dynamic IP, PPPoE,

PPTP, and Dynamic IP with Road Runner.

• Firewall

All unwanted packets from outside intruders are blocked to protect your Intranet.

• DHCP Server Supported

All of the networked computers can retrieve TCP/IP settings automatically from

this product.

• Web-Based Configuration

Configurable through any networked computer’s web browser using Netscape or

Internet Explorer.

• Virtual Server supported

Allows you to expose WWW, FTP, and other services on your LAN to the Internet.

• User-Definable Application Sensing Tunnel

User can open multiple ports for special applications that require multiple

connections like Internet gaming, video conferencing, Internet telephony, etc.

• DMZ Host Supported

Allows a networked computer to be fully exposed to the Internet; this function is

used when the special application sensing tunnel feature is insufficient to allow

an application to function correctly.

• Statistics of WAN Supported

o Enables you to monitor inbound and outbound packets

Security Functions

• Packet Filter Supported

Packet Filter allows you to control access to a network by analyzing the incoming

and outgoing packets and allowing or denying them access based on the IP

address of the source and destination.

• Domain Filter Supported

o Lets you prevent users from accessing specified domains through this

device.

• URL Blocking Supported

o Lets you prevent users from accessing specified URLs through this device.

• VPN Pass-Through

o Support VPN pass-through.

• SPI Mode Supported

o When SPI Mode is enabled, the router will check every incoming packet to

determine if the packet is valid.

• DoS Attack Detection Supported

o When this feature is enabled, the router will detect and log any DoS attack

that comes from the Internet.

Advanced Functions

• System Time Supported

o Allows you to synchronize the system time with a network time server.

• E-mail Alert Supported

o The router can send e-mail alerts to a specified e-mail address.

• Dynamic DNS Supported

o Supports dyndns,TZO.com, and dhs.org.

• SNMP Supported

o Supports basic SNMP functions.

• Routing Table Supported

o Supports static routing table.

• Schedule Rule Supported

o Schedule the time when services such as virtual server or packet filter will

be active.

Other Functions

• UPNP (Universal Plug-and-Play) Supported

2. Hardware Installation

2.1 Connect the Router

Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable

modem, and the router.

Step 1 Connect one end of a network cable to the WAN port of the router and connect

the other end of the cable to the DSL/Cable modem.

Step 2 With another network cable, connect one end of the cable to your computer’s

network card and connect the other end to one of the LAN ports of the router.

Step 3 Power on the DSL/Cable modem and wait for the lights on the modem to settle

down.

Step 4 Power on the router by connecting one end of the supplied power adapter to the

power jack of the router and connecting the other end to an electrical outlet.

Step 5 Power on your computer.

Step 6 Make sure the WAN and the LAN port that the computer is connected to are lit.

If not, try the above steps again.

2.2 Verify Connection to Router

Step 1 Go to Start, Run, type command (for Windows 95/98/ME) or cmd (for Windows

2000/XP) and click OK. You will see the command prompt as below.

Step 2 Type ping 192.168.1.1 and press Enter. You should get four reply responses

back.

Step 3 If you get Request timed out, or Destination host unreachable, double-check

the network cable connection between the computer and the router and try Step 2 again.

If you still encounter problem, go to the next step; otherwise proceed to Section 3,

Configure the Router.

Step 4 For Windows 2000/XP, type ipconfig/release and press Enter.

Step 5 Type ipconfig/renew and press Enter. You should get an IP address of

192.168.1.x (where x is a number between 2 - 254). Proceed to Section 3, Configure

the Router. If you don’t get an IP address, reset the router by holding in the reset

button at the back of the router for 10 seconds while it is ON and try ipconfig/renew

again.

Step 6 For Windows 95/98/ME go to Start, Run, type winipcfg and click OK.

Step 7 Select your network card from the drop-down menu and click Release.

Step 8 After your IP address is released, click Renew. You should get an IP address of

192.168.1.x (where x is a number between 2 - 254). If you don’t get an IP address,

reset the router by holding in the reset button at the back of the router for 10 seconds

while it is ON and try Renew again.

3. Configure the Router

3.1 Setup Wizard

Step 1 Open the web browser and type 192.168.1.1 in the URL Address field and press

Enter.

Step 2 Enter admin for the password field and click Log in.

Step 3 Click on Wizard from the main menu and click Next to begin the Setup Wizard.

Step 4 Select your WAN Type (Internet Connection Type) and click Next. If you are not

sure what your Internet Connection Type is, please contact your Internet Service

Provider (ISP) for assistance.

Cable Modem

If you use cable modem, select Obtain an IP address from ISP automatically

(Dynamic IP Address) and click Next. Proceed to Step 5a, Cable Modem.

DSL

If you use DSL, select Some ISPs require the use of PPPoE to connect to their

services (PPP over Ethernet) and click Next. Proceed to Step 5b, DSL.

For Cable Modem Users:

Step 5a If your ISP has provided you with a host name, enter it in the Host Name field.

If your ISP

requires a registered MAC Address, click on the Clone MAC button. Click Next when

done and proceed to Step 6.

For DSL Users:

Step 5b Fill in the applicable fields according to the information provided by your ISP.

Click Next when done and proceed to Step 6.

Note: Depending on the ISP, you may need to include the domain name with your

account name.

Example: [email protected]

Step 6 Click Reboot to apply your settings.

Step 8 Click OK to confirm reboot.

Step 9 Wait for the router to reboot and proceed to Section 4, Verify Connection

Status.

4. Verify Connection Status and Wireless Settings

4.1 Checking the System Status

View the System Status to verify your Internet connection.

Step 1 Login to the router’s web configuration page and click on the Status link from

the Main Menu.

Step 2 Verify that the WAN Status displays valid numbers (instead of all 0’s).

If you use Cable modem and you see all 0’s, click on the Renew button.

If you use DSL and you see all 0’s, click on the Connect button.

Step 3 Once you clicked the Renew or Connect button, you should see some numbers

under WAN Status. This means you have successfully established Internet connection.

Note: If you still see all 0’s after clicking on the Renew or Connect button, try the

troubleshooting tips at the end of this manual.

4.2 Connecting to the Router Wirelessly

Below are the default wireless settings of the router. You must configure your wireless

network adapter to the same settings in order to establish a wireless connection with the

router. Please refer to your wireless network adapter’s manual on how to configure

these settings.

SSID: default

Operating Mode: Infrastructure

Authentication: Open System

Channel #: 11

WEP: disabled

You may need to restart your computer after establishing a signal strength/link quality

with the router.

5. Web Configuration

5.1 Accessing the Web Configuration Utility

You may configure the router through the web browser using the Web Configuration

Utility.

Step 1 Open the web browser and type in 192.168.1.1 and press Enter.

Step 2 Enter admin for the password field and click Log in.

You will see the Web Configuration Utility’s home page (System Status). You can

navigate through the utility from the Main Menu located at the left side of the page.

5.2 Basic Setting

5.2.1 Primary Setup

You can set the router’s LAN IP address and change the WAN type (Internet

Connection Type) on this page.

LAN IP Address: The router’s default IP address is 192.168.1.1. You can change this

address to suit your existing network.

WAN Type: Displays the current WAN type (Internet Connection Type) selected. Click

the Change button to change the WAN type.

The following describes the various WAN types supported by the router:

Dynamic IP Address (For Cable Modem)

Host Name (optional): Some ISPs require a registered host name to connect to their

services. Enter the host name provided by your ISP, if applicable.

WAN’s MAC Address: Some ISPs require a registered MAC address to connect to

their services. Either manually enter the MAC address or click the Clone MAC button.

Renew IP Forever: Checking the Enable box will allow the router to automatically

renew the IP address automatically when the lease time is expired.

Click Save to save any changes or click Undo to cancel any changes.

Static IP Address

If your ISP assigns you static IP address, they will provide you the information for WAN

IP Address, WAN Subnet Mask, WAN Gateway, Primary and Secondary DNS.

Click Save to save any changes or click Undo to cancel any changes.

Road Runner

Enter the Account name and Password required to connect to your ISP. Some ISPs

require an additional Login Server.

Renew IP Forever: Checking the Enable box will allow the router to automatically

renew the IP address automatically when the lease time is expired.

Click Save to save any changes or click Undo to cancel any changes.

DSL (PPPoE)

LAN IP Address: The router’s default IP address is 192.168.1.1. You can change this

address to suit your existing network.

Enter the Account name and Password required to connect to your ISP. Some ISPs

require you to include the domain name with your account name in the Account name

field. Example: us[email protected]

Primary DNS and Secondary DNS: If your ISP provided you with the IP address of the

Primary and Secondary DNS servers, you may enter them in the respective field.

Maximum Idle Time (in seconds): Enter the maximum idle time (in seconds) before

the router disconnects the PPPoE session.

Auto-reconnect (check box): Checking this box enables the router to automatically

reconnect to the Internet once the connection is dropped.

Click Save to save any changes or click Undo to cancel any changes.

PPTP

Enter the information provided by your ISP in the respective fields.

Connection ID (optional): Some ISPs require the use of a connection ID.

Maximum Idle Time (in seconds): Enter the maximum idle time (in seconds) before

the router disconnects the PPPoE session.

Auto-reconnect (check box): Checking this box enables the router to automatically

reconnect to the Internet once the connection is dropped.

Click Save to save any changes or click Undo to cancel any changes.

Virtual Computers

The Virtual Computer function enables you to map the Global IP (WAN IP address)

assigned by your ISP to the Local IP (LAN IP address) of your computer.

Global IP: Enter the global IP address (WAN IP) assigned by your ISP.

Local IP: Enter the local IP address (LAN IP) of your computer you wish to map to.

Enable (check box): Check this box to enable the Virtual Computer function.

Click Save to save any changes or click Undo to cancel any changes.

Page is loading ...

Airlink101 AR325W User manual

Brand: Airlink101

Model: AR325W

Category: WLAN access points

Type: User manual

Download PDF

report

Airlink101 AR325W User manual

Airlink101 AR325W User manual

Related papers

Other documents