Acnodes FPC 8084 User manual

FPC 8084

All-in-One

8.4” Super Slim

PANEL PC

User ’s Manual

Disclaimers

The information in this manual has been carefully checked and is believed to be

accurate. Acnodes Co., Ltd. assumes no responsibility for any infringements of

patents or other rights of third parties, which may result from its use.

Acnodes assumes no responsibility for any inaccuracies that may be contained in this

document. Acnodes makes no commitment to update or to keep current the

information contained in this manual.

Acnodes reserves the right to make improvements to this document and/or

product at any time and without notice.

No part of this document may be reproduced, stored in a retrieval system, or

transmitted, in any form or by any means, electronic, mechanical, photocopying,

recording, or otherwise, without the prior written permission of Acnodes Co., Ltd.

©

rights reserved.

May 2005, Version A1

Printed in Taiwan

ii



CE Marking



FCC ClassA

Safety App rovals

FCC Compliance

This equipment has been tested and complies with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. If not installed and used in

accordance with proper instructions, this equipment might generate or

radiate radio frequency energy and cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measurers:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and

receiver.

3. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV

technician for help.

Shielded interface cables must be used in order to comply with

emission limits.ou

iii

Safety Precautions

Before getting started, read the following important cautions.

1. The

FPC 8084

does not come equipped with an

operating system. An operating system must be loaded

first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when

installing the internal components. Use a grounding wrist

strap and place all electronic components in any

static-shielded devices. Most electronic components are

sensitive to static electrical charge.

3. Disconnect the power cord from the FPC 8084T

before making any installation. Be sure both the system

and the external devices are turned OFF. Sudden surge

of power could ruin sensitivecomponents. Make

sure the FPC 8084 is properly grounded.

4. The brightness of the flat panel display decreases with

usage. However, hours of use vary depending on the

application environment.

5. Turn OFF the system power before cleaning. Clean the

system using a cloth only. Do not spray any liquid cleaner

directly onto the screen. The FPC 8084 may come with

or w/o a touchscreen. Although the touchscreen is

chemical resistant, it is recommended that you spray the

liquid cleaner on a cloth first before wiping the screen. In

case your system comes without the touchscreen, you

must follow the same procedure and not spray any

cleaner on the flat panel directly.

6. Avoid using sharp objects to operate the touchscreen.

Scratches on the touchscreen may cause malfunction or

internal failure to the touchscreen.

7. The flat panel display is not susceptible to shock or

vibration. When assembling the FPC 8084, make sure it

is securely installed.

iv

8. Do not open the systems back cover. If opening the

cover for maintenance is a must, only a trained

technician is allowed to do so. Integrated circuits on

computer boards are sensitive to static electricity. To

avoid damaging chips from electrostatic discharge,

observe the following precautions:

9

Before handling a board or integrated circuit, touch an

unpainted portion of the system unit chassis for a few

seconds. This will help to discharge any static electricity on

your body. When handling boards and components,

wear a wrist-grounding strap, available from most

electronic component stores.

Trademarks Acknowledgments

Acnodes is a trademark of Acnodes Co., Ltd.

IBM, PC/AT, PS/2, VGA are trademarks of I nternat ional

Business Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

MS -DOS, Micro s oft C and QuickBASIC are trademarks of

Microsoft Corporation.

VIA is a trademark of VIA Technologies, I nc.

SST is a trademark of Silicon Storage Technology, Inc.

UMC is a trademark of United Microelectronics

Corporation.

Other brand names and trademarks are the properties of

their re s pe cti ve o wners.

v

This page does not contain any information.

vi

Table of Contents

C h a p t e r 1 Introduction............................................1

1.1 General Description.................................................1

1.2 Specifications...........................................................2

1.2.1 Main CPU Board......................................................2

1.2.2 I/O System ...............................................................2

1.2.3 System Specification ..............................................9

1.3 Dimensions.............................................................10

1.4 I/O Outlets..............................................................11

1.5 Package List............................................................12

C h a p t e r 2 Hardware Installation ........................13

2.1 HDD Installation......................................................13

2.2 CF card Installation ..............................................15

2.3 Add-on Card Installation......................................16

2.4 3 x Serial Ports......................................................18

2.5 VGA ........................................................................20

2.6 Ethernet .................................................................20

2.7 Mountings: Panel / Wall / Desktop / VESA ..........21

2.7.1 VESA-ARM/Wall-Mount..........................................21

2.7.2 Desktop Kit Assembly.......................................22

2.7.3 Panel-mount Kit Assembly ....................................23

C h a p t e r 3 Driver Installation...............................24

3.1 System...................................................................24

3.2 Touch Screen........................................................24

3.2.1 Specification..........................................................24

3.2.2 Driver Installation- Windows

98/2000/XP/CE.NET/XP-Embedded .................................25

3.2.3 Driver Installation- DOS.........................................27

3.2.3.1 Using INSTALL.EXE utility to install PenMount

software driver. ...................................................................27

3.2.3.2 Identify the communication port and IRQ number

27

Table of Contents vii

3.2.3.3 Do Calibration .......................................................28

3.2.3.4 Initializing the PenMount driver ...........................29

3.2.4.5 Demonstration.......................................................29

3.2.4 Driver Installation- Linux .......................................29

3.2.4.1 Advance Setup .....................................................29

3.2.4.2 Install PenMount driver ........................... ..............30

3.2.4.3 Do Calibration .......................................................31

C h a p t e r 4 Embedded O.S. Installation..............32

4.1 Windows XP Embedded ......................................32

4.1.1 Penmount Touch Screen ......................................32

4.2 Windows CE.NET 4.2............................................33

4.2.1 Calibration Touch Screen ....................................33

A p p e n d i x A...............................................................34

Main Board BIOS Setup...................................................34

A.1 BIOS Introduction...................................................34

A.2 BIOS Setup..............................................................34

A.2.1 Standard CMOS Setup..........................................36

A.2.2 Advanced BIOS Features.....................................41

A.2.3 Advanced Chipset Features................................46

A.2.4 Integrated Peripherals ..........................................49

A.2.5 Power Management Setup ..................................53

A.2.6 PNP/PCI Configuration .........................................56

A.2.7 PC Health Status....................................................58

A.2.8 Frequency/Voltage Control ................................59

A.2.9 Load Fail-Safe Defaults.........................................60

A.2.10 Load Optimized Defaults......................................61

A.2.11 Set Supervisor/User Password..............................62

A.2.12 Save & Exit Setup...................................................63

A.2.13 Exit Without Saving................................................64

viii

Table of Contents

FPC 8084 All-in-One PANEL PC Users Manual

C h a p t e r 1

Introduction

This chapter contains the general information and the detail

specifications of the GOT-1840T. Chapter 1 includes the following

sections:



General Description



Sy stem Sp ecif icat ion



Di me ns ions

1.1 General Description



I/O Outlets



Utilities Supported



Package List

The FPC 8084 is a fan-less and compact-size touch panel computer,

and is equipped with a 8.4" TFT LCD display and low power

consumption CPU, the VIA Eden 667MHz. The FPC 8084 supports

Windows® 98/NT/2000/XP, Windows® CE.NET, Windows® XP

embedded, and Linux. The panel also includes a PC/104 slot for

extended communication or a DA&C card. The FPC 8084 is cost-

effective choice for operator interface applications.

Reliable and Stable Design

The FPC 8084 adopts a fan-less cooling system and a

CompactFlash™ card, which makes it especially suitable for

vibration-heavy environments, best for the transportation, ship, and

industrial machinery markets.

Flexibility- a PC/104 Slot

The

FPC 8084

offers a PC/104 slot that allows for extended

communication or a DA&C card, or even for a PC/104 motion card,

which can be used for different application requirements. With

Windows a CE.NET and a CompactFlash™ card combination, the

Panel is especially suitable for embedded applications.

Embedded O.S. Supported

The FPC 8084 not only supports Windows

®

98/NT/2000/XP, but

also supports embedded OS, such as Windows

®

CE.NET, and

Windows

®

XP embedded. For storage device, the F P C

8 0 8 4 supports 2.5" HDD or CompactFlash™ card.

Introduction 1

FPC 8084 Users Manual

Industrial-grade Product Design

The FPC 8084 has an incredible design that can be used in different

industrial harsh environments.

z

A fuse helps prevent over-voltage for power input.

z

Stainless steel back chassis and Aluminum front bezel meets the

IP65/NEMA4 standard.

z

For connecting other devices, the

FPC 8084

also features

several interfaces: USB, Ethernet, and RS-232/422/485.

1.2 Specifications

1.2.1 Main CPU Board



CPU:

VIA EDEN 4 00MHz, 667MHZ



System Chipset:

VT8606 (Twister-T) + VT82C686B



BIOS:

AWARD BIOS, Plug-and-Play 4Mbit Flash ROM

with SmartView VGA BIOS Function and

integrated Ethernet Novell RPL and Windows

PXE Boot ROM functions

.



System Memory:

One 144-pin DIMM socket.

Maximum up to 512MB SDRA

M

ECC/parity



L2 Cache:

Integrated in CPU



Watchdog Timer:

Generates a system reset or NMI by

jumper selectable

Software programmable time interval

64 levels , 0.5~8/5~80/50~80 0/100~1600

second

s

1.2.2 I/O System



Standard I/O:



3 x ser ial ports with power;

2 x RS-232 , 1 x

RS-232/422/485 jumper

selectable



1 x PS/2 Keyboard/Mouse

Interface



1x VGA Ports



2 x USB Ports 1.1 compliant

2 Introduction

FPC 8084 Users Manual

Ethernet:

- Realtek RTL 8100C PCI Bus 10/100M Base-T

- Wake-On-LAN

- RJ-45 interface equipped



Expansion Slot:

- one 16-bit PC/104 connector

1.2.3 System Specification



8.4” TFT LCD



Disk drive housing:

1 x internal 2.5” drive



100W DC power supply



Heat dispensing design



One slot for PC/104



Net weight:



18 Kgs

Dimension (main body size):



280 x 225 x

61.1mm

Operating temperature:

-1O° to 45°C ; Relative

umidity:50%

Relative humidity:

10% to 85% @ 40° C, on-condensing

Altitude:

10,000 ft. (3,000 meters)

V i b rat i on ( op e rating) :

5 to 500 Hz, 1.3 G random



Shock (

operating

):

10 G peak acceleration (11 msec.

duration)

9

FPC 8084 Users Manual

1.3 Dimensions

The following diagrams show the dimensions and outlines of

FPC 8084.

10

FPC 8084 Users Manual

1.4 I/O Outlets

The following figure shows the I/O locations of the FPC 8084. Most of

the I/O connectors are located on the back panel of the

FPC 8084.

1 2 3

4 5 6 7 8 9 10

1:

USB v1.1

6:

Keyboard/Mouse

2:

COM4 Port

7:

USB v1.1

3:

Power Switch

8:

COM1 Port

4:

VGA Port

9:

COM2 Port

5:

LAN (RJ45)

10:

DC inlet

11

FPC 8084 Users Manual

1.5 Package List

When you receive the FP C 8 084 there are following items in

the package.

1.

FPC 8084

x 1

2. Panel mount kit x 6

3. Desktop kit x 2

4. Desktop kit screw x 4

5. VESA ARM/Wall-mount kit x 1

6. CD driver x1

12

FPC 8084 Users Manual

C h a p t e r 2

Hardware Installation

The FPC 8084 provides lots of flexible ways for you to select different

configuration such as HDD, CF card and more. The chapter will show

you how to install the hardware. It includes:

2.1 HDD Installation

The FPCC 8084 offers a convenient drive bay module for users to

install HDD. The

FPC 8084

offers one 2.5” HDD drive for users to

install. Please follow the steps:

1. Open the HDD back chassis. Unscrew 4 screws of back and 4

screws of side.And take out the HDD bracket.

2. Screw 4 screws and fix HDD on the bracket kit.

13

FPC 8084 Users Manual

3. Fix the HDD bracket kit to system by 4 screws.

14

FPC 8084 Users Manual

2.2 CF card Installation

The FPC 8084 offers a convenient drive bay module for users to

install CF card. When installing the CF card, refer to the following

instructions and illustration:

1. Open the bottom chassis.

15

FPC 8084 Users Manual

2. Install user’s CF card.

2.3 Add-on Card Installation

The FPC 8084 provides one PC/104 slot. User could install one or

two PC/104 card. If user needs the PC/104 Box to protect add-on card,

user can order the ‘GOT-PC104-Kit’.

When upgrading the add-on card, refer to the following instructions

and illustration:

1. Remove the piece by 2 screws.

16

FPC 8084 Users Manual

2. Install PC/104 cards on the slot.

3. Set the bracket to protect.

17

FPC 8084 Users Manual

2.4 3 x Serial Ports

COM Port Connector: COM1

The connector, COM 1, is a DB-9 connector, and the following table

shows the pin assignments of this connector.

Pin Signal Name

1

DCD, Data carrier detect

2

RXD, Recei ve data

3

TXD, Transmit data

4

DTR, Data terminal ready

5

GND, ground

6

DSR, Data set ready

7

R TS, Request to send

8

CTS, Clear to send

9

RI, Ring ind i cato r

COM1

18

Page is loading ...

Acnodes FPC 8084 User manual

Acnodes FPC 8084 User manual

Related papers

Other documents