White Rodgers 1F80-0224 User manual

Brand: White Rodgers

Model: 1F80-0224

Category: Thermostats

Type: User manual

This manual is also suitable for

1F80-224

1F80-2241F80-224

1F80-224

Programmable Electronic Digital Thermostat

INSTALLATION ANDINSTALLATION AND

INSTALLATION AND

OPERATION INSTRUCTIONSOPERATION INSTRUCTIONS

OPERATION INSTRUCTIONS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLYFAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSEBEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

PERSONAL INJURY AND/OR PROPERTY DAMAGE.PERSONAL INJURY AND/OR PROPERTY DAMAGE.

PERSONAL INJURY AND/OR PROPERTY DAMAGE.

DESCRIPTIONDESCRIPTION

DESCRIPTION

• Temperature override until next program period

• Manual program override (HOLD temperature)

• Temporary HOLD

• °F/°C convertibility

• Temperature range 45° to 90°F

• RC, RH, W, Y, G , O and B terminals

• B and O terminals for single stage heat pumps (no auxiliary

heat) or damper operation

• Program storage in case of power loss

• 2 “AA” Energizer

alkaline batteries included

Operator: Save these instructions for future use!Operator: Save these instructions for future use!

Operator: Save these instructions for future use!

Your new White-Rodgers 24-Hour Digital Thermostat uses the

technology of a solid-state microcomputer to provide precise

time/temperature control. This thermostat offers you the flexibil-

ity to design heating and cooling programs that fit your needs.

Features:Features:

Features:

• Simultaneous heat and cool program storage

• Preprogrammed temperature control

• Four separate time/temperature settings

• LCD continuously displays setpoint, and alternately

displays time and room temperature

PRECAUTIONSPRECAUTIONS

PRECAUTIONS

This thermostat is intended for use with a low voltage system; do

not use this thermostat with a line voltage system. If in doubt

about whether your wiring is millivolt, line, or low voltage, have

it inspected by a qualified heating and air conditioning contractor

or electrician.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical codes and

ordinances.

This control is a precision instrument, and should be handled

carefully. Rough handling or distorting components could cause

the control to malfunction.

▲

CAUTIONCAUTION

CAUTION

To prevent electrical shock and/or equipment damage,To prevent electrical shock and/or equipment damage,

To prevent electrical shock and/or equipment damage,

disconnect electric power to system at main fuse ordisconnect electric power to system at main fuse or

disconnect electric power to system at main fuse or

circuit breaker box until installation is complete.circuit breaker box until installation is complete.

circuit breaker box until installation is complete.

▲

WARNINGWARNING

WARNING

Do not use on circuits exceeding specified voltage.Do not use on circuits exceeding specified voltage.

Do not use on circuits exceeding specified voltage.

Higher voltage will damage control and could causeHigher voltage will damage control and could cause

Higher voltage will damage control and could cause

shock or fire hazard.shock or fire hazard.

shock or fire hazard.

Do not short out terminals on gas valve or primaryDo not short out terminals on gas valve or primary

Do not short out terminals on gas valve or primary

control to test. Short or incorrect wiring will damagecontrol to test. Short or incorrect wiring will damage

control to test. Short or incorrect wiring will damage

thermostat and could cause personal injury and/orthermostat and could cause personal injury and/or

thermostat and could cause personal injury and/or

property damage.property damage.

property damage.

Thermostat installation and all components of theThermostat installation and all components of the

Thermostat installation and all components of the

system shall conform to Class II circuits per the NECsystem shall conform to Class II circuits per the NEC

system shall conform to Class II circuits per the NEC

code.code.

code.

SPECIFICATIONSSPECIFICATIONS

SPECIFICATIONS

ELECTRICAL DATAELECTRICAL DATA

ELECTRICAL DATA

Electrical Rating:Electrical Rating:

Electrical Rating:

8 to 30 VAC 50/60 Hz. or D.C.

0.05 to 1.0 Amps (Load per terminal)

1.5 Amps Maximum Total Load1.5 Amps Maximum Total Load

1.5 Amps Maximum Total Load (All terminals combined)

THERMAL DATATHERMAL DATA

THERMAL DATA

Setpoint Temperature Range:Setpoint Temperature Range:

Setpoint Temperature Range:

45°F to 90°F (7°C to 32°C)

Operating Ambient Temperature Range:Operating Ambient Temperature Range:

Operating Ambient Temperature Range:

32°F to 105°F

Operating Humidity Range:Operating Humidity Range:

Operating Humidity Range:

0 to 90% RH (non-condensing)

Shipping Temperature Range:Shipping Temperature Range:

Shipping Temperature Range:

-4°F to 150°F

APPLICATIONSAPPLICATIONS

APPLICATIONS

For use with:

• Standard heat/cool or heat only systems

• Electric heat systems

• Gas or oil fired systems

• Gas systems with intermittent ignition devices (I.I.D.)

and/or vent dampers

• Hydronic (hot water or steam) systems

• Single-stage heat pump systems (no auxiliary heat)

• Millivolt systems

DO NOT USE WITH:DO NOT USE WITH:

DO NOT USE WITH:

• Multi-stage systems

• Systems exceeding 30 VAC and 1.5 amps

• 3-wire zoned hydronic heating systems

WHITE-RODGERSWHITE-RODGERS

WHITE-RODGERS

EMERSON ELECTRIC CO.

9797 REAVIS ROAD

ST. LOUIS, MISSOURI 63123-5398

www.white-rodgers.com

Printed in U.S.A.

PART NO. 37-6350CPART NO. 37-6350C

PART NO. 37-6350C

Replaces 37-6350B

0326

Mounting

holes

Mounting

holes

Electric/Gas

switch

Screw anchors

INSTALLATIONINSTALLATION

INSTALLATION

REMOVE OLD THERMOSTATREMOVE OLD THERMOSTAT

REMOVE OLD THERMOSTAT

1. Shut off electricity at the main fuse box until installation is

complete. Ensure that electrical power is disconnected.

2. Remove the front cover of the old thermostat.

With wiresWith wires

With wires

still attached, still attached,

still attached, remove wall plate from the wall. If the old

thermostat has a wall mounting plate, remove the thermo-

stat and the wall mounting plate as an assembly.

Identify each wire attached to the old thermostat usingIdentify each wire attached to the old thermostat using

Identify each wire attached to the old thermostat using

the labels enclosed with the new thermostat.the labels enclosed with the new thermostat.

the labels enclosed with the new thermostat.

4. Disconnect the wires from old thermostat one at a time.

DODO

NOT LET WIRES FALL BACK INTO THE WALL.NOT LET WIRES FALL BACK INTO THE WALL.

NOT LET WIRES FALL BACK INTO THE WALL.

5. Install new thermostat using the following procedures.

ATTENTION!ATTENTION!

ATTENTION!

This product does not contain mercury. However, this product

may replace a unit which contains mercury.

Do not open mercury cells. If a cell becomes damaged, do not

touch any spilled mercury. Wearing nonabsorbent gloves, take

up the spilled mercury with sand or other absorbent material and

place into a container which can be sealed. If a cell becomes

damaged, the unit should be discarded.

Mercury must not be discarded in household trash. When the

unit this product is replacing is to be discarded, place in a

suitable container and return to White-Rodgers at 2895 Harrison

Street, Batesville, AR 72501-2117 for proper disposal.

ELECTRIC HEAT OR SINGLE-STAGEELECTRIC HEAT OR SINGLE-STAGE

ELECTRIC HEAT OR SINGLE-STAGE

HEAT PUMP SYSTEMSHEAT PUMP SYSTEMS

HEAT PUMP SYSTEMS

This thermostat is configured from the factory to operate a heat/

cool, fossil fuel (gas, oil, etc.), forced air system. It is configured

correctly for any system that DOES NOT require the thermostat

to energize the fan on a call for heat. If your system is an electric

heat or heat-pump system that REQUIRES the thermostat to

turn on the fan on a call for heat, locate the

GAS/ELECTRICGAS/ELECTRIC

GAS/ELECTRIC

switch switch

switch on the back of the thermostat (see fig. 1) and switch it to

the

ELECTRIC ELECTRIC

ELECTRIC position. This will allow the thermostat to ener-

gize the fan immediately on a call for heat. If you are unsure if

the heating/cooling system requires the thermostat to control

the fan, contact a qualified heating and air conditioning service

person.

ATTACH THERMOSTAT BASE TO WALLATTACH THERMOSTAT BASE TO WALL

ATTACH THERMOSTAT BASE TO WALL

1. Remove the packing material from the thermostat. Gently

pull the cover straight off the base. Forcing or prying on the

thermostat will cause damage to the unit. If necessary, move

the electric heat switch (see

ELECTRIC HEAT SYSTEMSELECTRIC HEAT SYSTEMS

ELECTRIC HEAT SYSTEMS,

above).

2. Connect wires beneath terminal screws on base using

appropriate wiring schematic (see figs. 2 through 7).

3. Place base over hole in wall and mark mounting hole

locations on wall using base as a template.

4. Move base out of the way. Drill mounting holes.

5. Fasten base loosely to wall, as shown in fig. 1, using two

mounting screws. Place a level against bottom of base,

adjust until level, and then tighten screws. (Leveling is for

appearance only and will not affect thermostat operation.) If

you are using existing mounting holes, or if holes drilled are

too large and do not allow you to tighten base snugly, use

plastic screw anchors to secure subbase.

6. Push excess wire into wall and plug hole with a fire-resistant

material (such as fiberglass insulation) to prevent drafts

from affecting thermostat operation.

BATTERY LOCATIONBATTERY LOCATION

BATTERY LOCATION

2 "AA" alkaline batteries are included in the thermostat at the

factory with a battery tag to prevent power drainage.

You mustYou must

You must

remove the battery tag to engage the batteriesremove the battery tag to engage the batteries

remove the battery tag to engage the batteries.

BATTBATT

BATT is displayed, the batteries are low and should be

replaced with fresh "AA" Energizer

alkaline batteries. To

replace batteries, install the batteries along the top of the base

(see Fig. 1). The batteries must be installed with the positive (+)

end to the left.

HYDRONIC (HOT WATER OR STEAM)HYDRONIC (HOT WATER OR STEAM)

HYDRONIC (HOT WATER OR STEAM)

HEATING SYSTEMSHEATING SYSTEMS

HEATING SYSTEMS

This thermostat is set to operate properly with a forced-air

heating system. If you have a hydronic heating system (a

system that heats with hot water or steam), you must set the

thermostat to operate properly with your system. Change the

second option in the configuration menu to SL (see CONFIGU-

RATION MENU, page 4).

CHECK THERMOSTAT OPERATIONCHECK THERMOSTAT OPERATION

CHECK THERMOSTAT OPERATION

If at any time during testing your system does not operate

properly, contact a qualified service person.

Turn on power to the system.

Fan OperationFan Operation

Fan Operation

If your system

does notdoes not

does not have a

G terminal connection, skip to

Heating SystemHeating System

Heating System.

1. Move fan to

ON ON

ON position. The blower should begin to

operate.

2. Move fan switch to

AUTO AUTO

AUTO position. The blower should

stop immediately.

Figure 1. Thermostat BaseFigure 1. Thermostat Base

Figure 1. Thermostat Base

24 VAC

120 VAC

Hot

Neutral

THERMOSTAT

SYSTEM

G W

Figure 2. Typical wiring diagram for

heat only, 3-wire, single transformer systems

TRANSFORMER

Heating

System

Fan

Relay

JUMPER

WIRE

For 2-wire Heat only,

attach to RH and W

NOTE

24 VAC

120 VAC

Hot

Neutral

TRANSFORMER

THERMOSTAT

SYSTEM

G W

Figure 3. Typical wiring diagram for

cool only, 3-wire, single transformer systems

Cooling

System

Fan

Relay

RCOB

JUMPER

WIRE

24 VAC

120 VAC

Hot

Neutral

THERMOSTAT

SYSTEM

G W

Figure 4. Typical wiring diagram for

heat/cool, 4-wire, single transformer systems

TRANSFORMER

Heating

System

Fan

Relay

Cooling

System

JUMPER

WIRE

RED jumper wire (provided with thermostat) must be

connected between thermostat RH and RC terminals

for proper thermostat operation with this system.

NOTE

24 VAC

120 VAC

Hot

Neutral

THERMOSTAT

SYSTEM

G W

Figure 5. Typical wiring diagram for

heat/cool, 5-wire, two-transformer systems

HEATING

TRANSFORMER

Heating

System

Fan

Relay

Cooling

System

24 VAC

120 VAC

Hot

Neutral

COOLING TRANSFORMER

24 VAC

120 VAC

Hot

Neutral

THERMOSTAT

SYSTEM

G W

Figure 6. Typical wiring diagram for heat pump

with reversing valve energized in COOL

TRANSFORMER

Reversing

Valve*

RCOB

JUMPER

WIRE

Compressor

Contactor

JUMPER

WIRE

* Reversing valve is energized when the

system switch is in the COOL position

Fan

Relay

24 VAC

120 VAC

Hot

Neutral

THERMOSTAT

SYSTEM

G W

Figure 7. Typical wiring diagram for heat pump

with reversing valve energized in HEAT

TRANSFORMER

Reversing

Valve*

RCO

JUMPER

WIRE

Compressor

Contactor

JUMPER

WIRE

* Reversing valve is energized when the

system switch is in the HEAT position

Fan

Relay

Heating SystemHeating System

Heating System

1. Move SYSTEM switch to

HEATHEAT

HEAT position. If the heating

system has a standing pilot, be sure to light it.

2. Press to adjust thermostat setting above room tempera-

ture. The heating system should begin to operate.

3. Press

to adjust temperature setting below room tem-

perature. The heating system should stop operating.

To prevent compressor and/or property damage, if theTo prevent compressor and/or property damage, if the

To prevent compressor and/or property damage, if the

outdoor temperature is below 50°F, DO NOT operateoutdoor temperature is below 50°F, DO NOT operate

outdoor temperature is below 50°F, DO NOT operate

the cooling system.the cooling system.

the cooling system.

1. Move SYSTEM switch to

COOLCOOL

COOL position.

2. Press to adjust thermostat setting below room tempera-

ture. The blower should come on immediately on high

speed, followed by cold air circulation

3. Press to adjust temperature setting above room tem-

perature. The cooling system should stop operating.

Cooling SystemCooling System

Cooling System

▲

CAUTIONCAUTION

CAUTION

Before you begin programming your thermostat, you should be

familiar with its features and with the display and the location

and operation of the thermostat buttons. Your thermostat con-

sists of two parts: the

thermostat coverthermostat cover

thermostat cover and the

basebase

base. To

remove the cover, pull it straight out from the base. To replace

the cover, line up the cover with the base and press until the

cover snaps onto the base.

The Thermostat Buttons The Thermostat Buttons

The Thermostat Buttons

and Switchesand Switches

and Switches

Raises temperature setting.

Lowers temperature setting.

TIME button.

PRGM (program) button.

RUN (run program) button.

HOLD temperature button.

FAN switch (

ONON

ON,

AUTOAUTO

AUTO).

SYSTEM switch (

COOLCOOL

COOL,

OFFOFF

OFF,

HEATHEAT

HEAT).

The DisplayThe Display

The Display

Flame iconFlame icon

Flame icon ( ) is displayed when the SYSTEM switch is in

the HEAT position.

Snowflake iconSnowflake icon

Snowflake icon (

)is displayed (non-

flashing) when the SYSTEM switch is in the COOL position.

SnowflakeSnowflake

Snowflake is displayed (flashing) if the thermostat is in

lockout mode to prevent the compressor from cycling too

quickly.

Displays

BATTBATT

BATT when the 2 "AA" batteries are low and

should be replaced. Only

BATTBATT

BATT and

LOLO

LO in the minutes field

are displayed when batteries are low with no system

power.

Alternately displays current time and temperature. Dis-

plays

LOLO

LO in the minutes field when batteries are low.

The word

HOLDHOLD

HOLD is displayed when the thermostat is in the

HOLD mode.

HOLDHOLD

HOLD is displayed flashing when the thermo-

stat is in a temporary HOLD Mode.

Displays currently programmed set temperature (this is

blank when SYSTEM switch is in the OFF position).

CONFIGURATION MENUCONFIGURATION MENU

CONFIGURATION MENU

The configuration menu allows you to set certain thermostat

operating characteristics to your system or personal require-

ments.

Press RUN to make sure the thermostat is in the run program

mode, then press PRGM and RUN at the same time to enter the

configuration menu. The display will show the first item in the

configuration menu.

The configuration menu table summarizes the configuration

options. An explanation of each option follows.

Press HOLD to change to the next menu item or press TIME to

go backwards to the previous item in the menu. To exit the menu

and return to the program operation, press RUN. If no keys are

pressed within fifteen minutes, the thermostat will revert to

normal operation.

OPERATIONOPERATION

OPERATION

1)1)

Select Temporary Hold Time Select Temporary Hold Time

Select Temporary Hold Time - The thermostat can hold

any temperature you set it to for the amount of time you

select on this option. Your choices are 0:00 to 8:00 hours in

15 minute increments. 0:00 disables the function

Example:

1. You have selected 3:00 hours for the Temporary Hold

time period.

2. With the thermostat set to Heat or Cool, press HOLD

forfor

for

approximately five secondsapproximately five seconds

approximately five seconds until HOLD time (3:00

indicating 3 hours) appears as a setting reminder.

3. After releasing the button,

HOLDHOLD

HOLD on the display will

blink.

4. Use

or to set the temperature to your prefer-

ence. The thermostat will maintain this temperature

setting for 3 hours with

HOLDHOLD

HOLD blinking to remind you it is

in Temporary Hold. After 3 hours the thermostat will go

back to the program temperature and

HOLDHOLD

HOLD will no

longer blink or display.

2)2)

Select FA or SL (Fast or Slow) Heating Cycle RateSelect FA or SL (Fast or Slow) Heating Cycle Rate

Select FA or SL (Fast or Slow) Heating Cycle Rate - The

FA setting is frequently used for gas, oil or electric heat. The

SL setting produces a longer heating cycle which is nor-

mally for hot water or steam (hydronic) systems. Both

settings produce very accurate temperature control and

can be set to your personal preference. FA cycles the

system just under 1°F and the SL setting cycles at approxi-

mately 1.5°F.

3)3)

Select backlit display Select backlit display

Select backlit display - The display backlight improves

display contrast in low lighting conditions. Selecting back-

light ON will keep the light on for a short period of time after

any key is pressed. Selecting OFF will keep the light off.

4)4)

Select Compressor Lockout LOC OFF or ONSelect Compressor Lockout LOC OFF or ON

Select Compressor Lockout LOC OFF or ON - Selecting

LOC ON will cause the thermostat to wait 5 minutes before

turning on the compressor if the heating and cooling sys-

tem loses power. It will also wait 5 minutes minimum

between cooling cycles. This is intended to help protect the

compressor from short cycling. Some newer compressors

already have a time delay built in and do not require this

feature. Your compressor manufacturer can tell you if the

feature is already present in their system. When the

compressor time delay occurs it will flash the (snowflake

icon) for about five minutes then turn on the compressor.

Step Press Button(s) Displayed (Factory Default) Press or to select: COMMENTS

HOLD

(0:00)

0 to 8 hrs (in

15 minute increments)

(FA)

Select temporary Hold time

LOC

(OFF)

0 HI

(0)

4 LO to

4 HI

(F) C

Returns to normal operation

Select compressor lockout OFF or ON

Select temperature display adjustment higher or lower

Select temperature display to F or C

RUN

PRGM

and RUN

HOLD

d-L

(ON)

OFF

Select display backlight OFF or ON

HOLD

Select FA or SL (Fast or Slow) heating cycle rate

Configuration Menu

* Press

HOLD to advance to next item or TIME to move backwards to previous item

Select Temperature Display Adjustment 4 LO to 4 HISelect Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI -

Allows you to adjust the room temperature display 4° higher

or lower. Your thermostat was accurately calibrated at the

factory but you have the option to change the display

temperature to match your previous thermostat.

6)6)

Select F° or C° ReadoutSelect F° or C° Readout

Select F° or C° Readout - Changes the display readout to

Centigrade or Fahrenheit as required.

OPERATING FEATURESOPERATING FEATURES

OPERATING FEATURES

Now that you are familiar with the thermostat buttons and

display, read the following information to learn about the many

features of the thermostat.

•

SIMULTANEOUS HEATING/COOLING PROGRAMSIMULTANEOUS HEATING/COOLING PROGRAM

SIMULTANEOUS HEATING/COOLING PROGRAM

STORAGE STORAGE

STORAGE — When programming, you can enter both

your heating and cooling programs at the same time. There

is no need to reprogram the thermostat at the beginning of

each season.

•

TEMPERATURE OVERRIDETEMPERATURE OVERRIDE

TEMPERATURE OVERRIDE — Press

or until the

display shows the temperature you want. The thermostat

will override current programming and keep the room

temperature at the selected temperature until the next

program period begins. Then the thermostat will automati-

cally revert to the program.

•

HOLD TEMPERATUREHOLD TEMPERATURE

HOLD TEMPERATURE — The thermostat can hold any

temperature within its range for an indefinite period without

reverting to the programmed temperature. Momentarily

press HOLD button.

HOLDHOLD

HOLD will be displayed. Then choose

the desired temperature by pressing

or . The

thermostat will hold the room temperature at the selected

setting until you press RUN button to start program opera-

tion again.

•

CONFIGURATION MENUCONFIGURATION MENU

CONFIGURATION MENU — Allows you to customize

certain thermostat options.

PROGRAMMING YOUR THERMOSTATPROGRAMMING YOUR THERMOSTAT

PROGRAMMING YOUR THERMOSTAT

This section will help you plan your thermostat’s program to

meet your needs. For maximum comfort and efficiency, keep

the following guidelines in mind when planning your program.

• When heating (cooling) your building, program the

temperatures to be cooler (warmer) when the building is

vacant or during periods of low activity.

• During early morning hours, the need for cooling is

usually minimal.

Planning Your ProgramPlanning Your Program

Planning Your Program

Look at the factory preprogrammed times and temperatures

shown in the sample schedule. If this program will suit your

needs, simply press the RUN button to begin running the factory

preset program.

If you want to change the preprogrammed times and tempera-

tures, follow these steps.

Determine the time periods and temperatures for your program.

You must program four time periods. However, you may use the

same heating and cooling temperatures for consecutive time

periods.

Use the following table to plan your program time periods and

the temperatures you want during each period. Fill in the

complete table to have a record of your programs.

Start

Time Temperature

1ST HEAT 6:00 AM 70˚F

2ND HEAT 8:00 AM 62˚F

3RD HEAT 5:00 PM 70˚F

4TH HEAT 10:00 PM 62˚F

1ST COOL 6:00 AM 78˚F

2ND COOL 8:00 AM 85˚F

3RD COOL 5:00 PM 78˚F

4TH COOL 10:00 PM 82˚F

SAMPLE

Heating/Cooling Schedule Plan (Factory Program)

Period

Start

Time Temperature

1ST HEAT

2ND HEAT

3RD HEAT

4TH HEAT

1ST COOL

2ND COOL

3RD COOL

4TH COOL

Heating/Cooling Schedule Plan

Period

If the outside temperature is below 50°F, disconnectIf the outside temperature is below 50°F, disconnect

If the outside temperature is below 50°F, disconnect

power to the cooling system before programming.power to the cooling system before programming.

power to the cooling system before programming.

Energizing the air conditioner compressor duringEnergizing the air conditioner compressor during

Energizing the air conditioner compressor during

cold weather may cause personal injury or propertycold weather may cause personal injury or property

cold weather may cause personal injury or property

damage.damage.

damage.

▲

CAUTIONCAUTION

CAUTION

1. Move SYSTEM switch to

COOLCOOL

COOL position.

2. Follow the procedure for entering your cooling program,

using your selected cooling times and temperatures.

Enter Cooling ProgramEnter Cooling Program

Enter Cooling Program

CHECK YOUR PROGRAMMINGCHECK YOUR PROGRAMMING

CHECK YOUR PROGRAMMING

Follow these steps to check your thermostat programming one

final time before beginning thermostat operation.

1. Move SYSTEM switch to

HEATHEAT

HEAT position.

2. Press PRGM to view the 1st heating period time and

temperature. Each time you press PRGM, the next heating

period time and temperature will be displayed in sequence

(you may change any time or temperature during this proce-

dure).

3. Press RUN.

4. Move SYSTEM switch to

COOLCOOL

COOL position.

5. Repeat step 2 to check cooling program.

6. Move SYSTEM switch to

HEATHEAT

HEAT or

COOLCOOL

COOL and press RUN to

begin program operation.

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED ANDYOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND

READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

Reset OperationReset Operation

Reset Operation

If a voltage spike or static discharge blanks out the display or

causes erratic thermostat operation you can reset the thermo-

stat by pressing

, and TIME at the same time. This also

resets the factory defaults to the configuration menu and

program. If the thermostat has power, has been reset and still

does not function correctly contact your heating/cooling ser-

vice person or place of purchase.

BatteriesBatteries

Batteries

For optimum performance, we recommend replacing batteries

once a year with fresh "AA" Energizer

alkaline batteries.

TROUBLESHOOTINGTROUBLESHOOTING

TROUBLESHOOTING

Entering Your ProgramEntering Your Program

Entering Your Program

Follow these steps to enter the heating and cooling programs

you have selected.

Set Current TimeSet Current Time

Set Current Time

1. Press TIME button once. The display will show the hour only.

EXAMPLE:

2. Press and hold either or until you reach the correct

hour and AM/PM designation (

AMAM

AM begins at midnight;

PMPM

begins at noon).

3. Press TIME once. The display window will show the minutes

only.

EXAMPLE:

4. Press and hold either or until you reach the correct

minutes.

Enter Heating ProgramEnter Heating Program

Enter Heating Program

1. Move the SYSTEM switch to

HEATHEAT

HEAT.

2. Press PRGM once. Displayed are the currently programmed

start time for the

1st heating1st heating

1st heating period and the currently

programmed temperature (flashing).

EXAMPLE:

This display window shows that for the 1st weekday period,

the start time is 6:00 AM, and 70° is the programmed

temperature (this example reflects factory preprogramming).

3. Press

or to change the displayed temperature to

your selected temperature for the 1st heating program

period.

4. Press TIME once (the programmed time will flash). Press

or until your selected time appears. The time will

change in 15 minute increments. When your selected time

is displayed, press TIME again to return to the change

temperature mode.

5. Press PRGM once. The currently programmed start time

and setpoint temperature for the

2nd heating2nd heating

2nd heating program

period will appear.

6. Repeat steps 3 and 4 to select the start time and heating

temperature for the 2nd heating program period.

7. Repeat steps 3 through 5 for the 2nd, 3rd and 4th heating

program periods. Programming is now complete.

8. When you have completed entering your program, press

RUN.

For Troubleshooting information, see next page

SymptomSymptom

Symptom

ossibossib

ossib

le Causele Cause

le Cause

Corrective ActionCorrective Action

Corrective Action

No Heat/No Cool/No Fan 1. Blown fuse or tripped circuit breaker. Replace fuse or reset breaker.

(common problems) 2. Furnace power switch to OFF. Turn switch to ON.

3. Furnace blower compartment door or Replace door panel in proper position to engage

panel loose or not properly installed. safety interlock or door switch.

No Heat 1. Pilot light not lit. Re-light pilot.

2. System Switch not set to Heat. Set System Switch to Heat and raise setpoint

above room temperature.

3. Loose connection to thermostat or system. Verify thermostat and system wires are securely

attached.

4. Furnace Lock-Out Condition. Heat may also Many furnaces have safety devices that shut the

be intermittent. system down when a lock-out condition occurs.

If the heat works intermittently contact the furnace

manufacturer or local service person for assistance.

5. Heating System requires service or Diagnostic: Set System Switch to Heat and raise

thermostat requires replacement. the setpoint above room temperature. Within a few

seconds the thermostat should make a soft click

sound. This sound usually indicates the thermostat

is operating properly. If the thermostat does not

click, try the reset operation listed above. If the

thermostat does not click after being reset contact

your heating and cooling service person or place

of purchase for a replacement. If the thermostat

clicks, contact the furnace manufacturer or a

service person to verify the heating system is

operating correctly.

No Cool 1. System Switch not set to Cool. Set System Switch to Cool and lower setpoint

below room temperature.

2. Loose connection to thermostat or system. Verify thermostat and system wires are securely

attached.

3. Cooling System requires service or thermostat Same procedure as diagnostic for No Heat

requires replacement. condition except set the thermostat to Cool and

lower the setpoint below the room temperature.

There may be up to a five minute delay before

the thermostat clicks in Cooling if the compressor

lock-out option is selected in the configuration

menu (Item 6).

Heat, Cool or Fan Runs Constantly. 1. Possible short in wiring. Check each wire connection to verify they are

2. Possible short in thermostat. not shorted or touching together. No bare wire

3. Possible short in Heat/Cool/Fan system. should stick out from under terminal screws.

4. Fan Switch set to Fan On. Try resetting the thermostat. If the condition

persists the manufacturer of your system

or service person can instruct you on how

to test the Heat/Cool system for correct

operation. If the system operates correctly,

replace the thermostat.

Furnace Cycles Too Fast or Too Slow 1. The location of the thermostat and/or the size Item 2 in the Configuration Menu is the adjustment

(narrow or wide temperature swing) of the Heating System may be influencing the that controls the cycle rate. If an acceptable cycle

cycle rate. rate is not achieved using the FA (Fast) or SL

(Slow) adjustment contact a local service person for

additional suggestions.

Cooling Cycles Too Fast or Too Slow 1. The location of the thermostat and/or the size The cycle rate for cooling is fixed and can not be

(narrow or wide temperature swing) of the Cooling System may be influencing the adjusted. Contact a local service person for

cycle rate. suggestions.

Thermostat Setting and Thermometer 1. Thermostat thermometer setting requires The thermometer can be adjusted +/- 4 degrees as

Disagree adjustment. listed in item 7 of the Configuration Menu. No other

adjustment is possible.

Clock Loses or Gains Time 1. Loss of power to thermostat and low batteries. The thermostat will maintain its program in memory

even with no power/no batteries but the clock time

will be incorrect when power is restored. See No

Heat/No Cool/No Fan (common problems) above

for items to check in the system.

Heat or Cool Starts Early 1. EMR activated See Configuration Menu (Item 4).

Thermostat Does Not Follow Program 1. AM or PM set incorrectly in program. Check current clock and program settings including

2. AM or PM set incorrectly on the clock. the AM or PM designations for each time period.

3. Voltage spike or static discharge. If a voltage spike or static discharge occurs use the

Reset Operation listed above.

Blank Display and/or Keypad Not 1. Loss of power and dead batteries. Replace batteries and check heat/cool system for

Responding 2. Voltage Spike or Static Discharge. proper operation. If a voltage spike or static discharge

occurs use the Reset Operation listed above.

TROUBLESHOOTINGTROUBLESHOOTING

TROUBLESHOOTING

For additional product information, visit

www.white-rodgers.comwww.white-rodgers.com

www.white-rodgers.com

White Rodgers 1F80-0224 User manual

Brand: White Rodgers

Model: 1F80-0224

Category: Thermostats

Type: User manual

This manual is also suitable for

1F80-224

Download PDF

report

White Rodgers 1F80-0224 User manual

This manual is also suitable for

White Rodgers 1F80-0224 User manual

Related papers

Other documents