Carver 40my Assembly Instruction

Brand: Carver

Model: 40my

Type: Assembly Instruction

Carver 40my is a 40-foot motor yacht that can accommodate up to 10 people. It features a spacious cabin top, hardtop, arch, and aft deck. The yacht comes with a variety of amenities, including a wet bar, exterior seating, and a TV antenna. It is also equipped with a powerful engine and a variety of safety features, making it an ideal choice for both experienced and novice boaters. Whether you are looking to cruise the open waters or simply relax and enjoy the scenery, the Carver 40my is the perfect boat for you.

Carver 40my is a 40-foot motor yacht that can accommodate up to 10 people. It features a spacious cabin top, hardtop, arch, and aft deck. The yacht comes with a variety of amenities, including a wet bar, exterior seating, and a TV antenna. It is also equipped with a powerful engine and a variety of safety features, making it an ideal choice for both experienced and novice boaters. Whether you are looking to cruise the open waters or simply relax and enjoy the scenery, the Carver 40my is the perfect boat for you.

Page 1 of 1

40 Motor Yacht Setup Part Number 9991904 3/07

40 Motor Yacht Setup

1. Install props and rudders; install starboard side

steering linkage ﬁrst. Make sure rudder cotter keys

are installed.

2. Remove tape and clean the areas where the bridge

will set. Check for voids along the top of the

windows.

3. Install bridge aft seat base (ﬁberglass part

surrounding companionway door) with 9 white

truss head screws.

4. Apply sealant (732 white multi-purpose sealant)

around deck bolts. Also, place sealant forward of

forward deck bolts. (Refer to attached picture.)

5. Install arch to bridge.

NOTE:

e arch must be installed on the bridge to

complete step 6.

6. e lifting points for the bridge are between the

two stand-oﬀs on the forward bridge rail, and

around the arch top (use small straps). Position

bridge over boat. Run the appropriate wires to

the aft port corner; run the cables and steering

line to the forward starboard side; run the drain

line, water line, and appropriate wires to the aft

starboard corner.

7. Set bridge in place, making sure that no wires or

hoses get caught or pinched oﬀ. Make sure the

bridge is pushed all the way forward.

8. With the bridge in place, bolt it down:

a. Four bolts under helm.

b. One bolt on each side aft.

c. Two bolts under port seat.

d. One bolt under storage shelf starboard.

e. One bolt under starboard seat.

9. Install port and starboard hardtop supports and

door frames (leave them loose).

10. Slide hardtop into place. Secure it to arch,

support, and door frame.

NOTE:

Apply a small amount of 732 sealant in the

hole for the hardtop support.

11. Install handrail to bridge.

12. Install aft deck storage box. Secure access panel

and towel bar.

13. Install hardtop ﬁller pieces.

14. Install arch to hardtop glass.

15. Install exterior seating on bridge and aft deck.

16. Install mast light and TV antenna on arch.

17. Connect all dash wiring and wet bar hoses.

18. Cosmetically seal around hardtop support and

door frames.

Cabin Top: Place dab of sealant forward of forward deck

bolts.

1

Carver 40my Assembly Instruction

Brand: Carver

Model: 40my

Type: Assembly Instruction

Carver 40my is a 40-foot motor yacht that can accommodate up to 10 people. It features a spacious cabin top, hardtop, arch, and aft deck. The yacht comes with a variety of amenities, including a wet bar, exterior seating, and a TV antenna. It is also equipped with a powerful engine and a variety of safety features, making it an ideal choice for both experienced and novice boaters. Whether you are looking to cruise the open waters or simply relax and enjoy the scenery, the Carver 40my is the perfect boat for you.

Related papers

Other documents