Dell PowerVault MD1000 User guide

Type
User guide

Dell PowerVault MD1000 is a storage enclosure that supports host-based RAID configuration using Dell PowerEdge RAID Controller (PERC) 5/E and PERC 6/E. It's a scalable solution that allows you to add storage capacity to your server as needed. With redundant path connectivity, if one path fails, another path can be used to communicate between the controller and the hard drive, maximizing uptime and data availability. The MD1000 is compatible with Dell PowerEdge servers and can be managed using Dell's OpenManage software.

Dell PowerVault MD1000 is a storage enclosure that supports host-based RAID configuration using Dell PowerEdge RAID Controller (PERC) 5/E and PERC 6/E. It's a scalable solution that allows you to add storage capacity to your server as needed. With redundant path connectivity, if one path fails, another path can be used to communicate between the controller and the hard drive, maximizing uptime and data availability. The MD1000 is compatible with Dell PowerEdge servers and can be managed using Dell's OpenManage software.

Dell PowerVault MD1000
Storage Enclosure
Information Update
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
____________________
Information in this document is subject to change without notice.
© 2005–2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell™, the DELL™ logo, PowerEdge™, and PowerVault™ are
trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
June 2010 Rev. A01
Information Update 3
RAID Configuration Update
Host-based RAID configuration is supported using Dell PowerEdge RAID
Controller (PERC) 5/E and PERC 6/E.
Supported Hardware Configurations Using a
PERC 6/E Adapter
PERC 6/E adapters can detect and use redundant paths to drives in a Dell
PowerVault MD1000 enclosure. With redundant paths, if one path fails,
another path can be used to communicate between the controller and the
hard drive.
NOTE: Redundant path connectivity is not supported on PERC 5/E adapters.
Figure 1 Redundant Path With One Enclosure
Server
PowerVault
MD1000 storage
enclosure
4 Information Update
Figure 2. Redundant Path With Two Enclosures
Figure 3. Redundant Path With Three Enclosures
Server
PowerVault
MD1000 storage
enclosure
PowerVault
MD1000 storage
enclosure
Server
PowerVault
MD1000 storage
enclosure
PowerVault
MD1000 storage
enclosure
PowerVault
MD1000 storage
enclosure
Information Update 5
Additional Information for Troubleshooting a
SAS/SATA drive
Reseating a drive during initial set up is a valid step. If an enclosure is in
production and if there are no problems other than non-detection of a drive,
replace the drive that is not detected rather than reseating the drive.
It is recommended not to reseat a SMART tripped or failed drive. You cannot
reset a SMART tripped drive back to normal state. If a drive fails due to the
controller, check if a new firmware is available to fix the issue. If a firmware
update does not fix the issue, replace the drive.
NOTE: If an amber blink sequence represents a SMART trip, the drive must be
replaced. It cannot be fixed by a firmware update.
For more information about troubleshooting a SAS/SATA drive, see the Dell
PowerVault MD1000 Storage Enclosure Hardware Owner’s Manual at
support.dell.com/manuals.
Troubleshooting Enclosure Problems
Problem
One of the temperature probes displays an abnormal temperature reading.
Action
The system management software displays four temperature probes (0-3).
Probe 0 represents the temperature sensor on
enclosure management module
(
EMM) 0. Probe 1 represents the temperature sensor on EMM1. Probe 2 and
3 are temperature sensors on the midplane.
To resolve this issue:
Check for airflow obstruction.
Replace the component with the abnormal temperature sensor.
NOTE: The power supplies do not have a temperature sensor that reports to the
system management software.
6 Information Update
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Dell PowerVault MD1000 User guide

Type
User guide

Dell PowerVault MD1000 is a storage enclosure that supports host-based RAID configuration using Dell PowerEdge RAID Controller (PERC) 5/E and PERC 6/E. It's a scalable solution that allows you to add storage capacity to your server as needed. With redundant path connectivity, if one path fails, another path can be used to communicate between the controller and the hard drive, maximizing uptime and data availability. The MD1000 is compatible with Dell PowerEdge servers and can be managed using Dell's OpenManage software.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI