Sony PMW-TD300 Operating instructions

4-408-371-11 (1)

Solid-State Memory

3D Camcorder

Operating Instructions

Before operating the unit, please read this manual thoroughly

and retain it for future reference.

PMW-TD300

2

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

• Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that

produce heat.

• Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding-type

plug has two blades and a third grounding

prong. The wide blade or the third prong

are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of

the obsolete outlet.

• Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

• Only use attachments/accessories

specified by the manufacturer.

• Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

• Unplug this apparatus during lightning

storms or when unused for long periods of

time.

• Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or

has been dropped.

To reduce the risk of fire or

electric shock, do not

expose this apparatus to

rain or moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to qualified

personnel only.

CAUTION

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type recommended by the manufacturer.

When you dispose of the battery, you must

obey the law in the relative area or country.

When installing the installation space must

be secured in consideration of the ventilation

and service operation.

• Do not block the ventilation slots at the left

side and right side panels, and vents of

the fans.

• Leave a space around the unit for

ventilation.

• Leave more than 40 cm of space in the

rear of the unit to secure the operation

area.

When the unit is installed on the desk or the

like, leave at least 4 cm of space in the left

and right sides. Leaving 40 cm or more of

space above the unit is recommended for

service operation.

CAUTION

The apparatus shall not be exposed to

dripping or splashing. No objects filled with

liquids, such as vases, shall be placed on the

apparatus.

WARNING

Excessive sound pressure from earphones

and headphones can cause hearing loss.

WARNING

3

In order to use this product safely, avoid

prolonged listening at excessive sound

pressure levels.

Batteries shall not be exposed to excessive

heat such as sunshine, fire or the like.

For the customers in the U.S.A.

This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the

interference at his own expense.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

All interface cables used to connect

peripherals must be shielded in order to

comply with the limits for a digital device

pursuant to Subpart B of Part 15 of FCC

Rules.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) this device may not cause

harmful interference, and (2) this device

must accept any interference received,

including interference that may cause

undesired operation.

For the customers in Canada

This Class A digital apparatus complies with

Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies

with the EMC Directive issued by the

Commission of the European Community.

Compliance with this directive implies

conformity to the following European

standards:

• EN55103-1: Electromagnetic Interference

(Emission)

• EN55103-2: Electromagnetic

Susceptibility (Immunity)

This product is intended for use in the

following Electromagnetic Environments: E1

(residential), E2 (commercial and light

industrial), E3 (urban outdoors), E4

(controlled EMC environment, ex. TV

studio).

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japan.

The Authorized Representative for EMC and

product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee

matters please refer to the addresses given

in separate service or guarantee documents.

For the State of California, USA only

Perchlorate Material - special handling may

apply, See

www.dtsc.ca.gov/hazardouswaste/

perchlorate

Perchlorate Material : Lithium battery

contains perchlorate.

For the customers in Taiwan only

Table of Contents

4

Foreword .................................................................................................... 10

Before Use....................................................................................... 10

Chapter 1 : Overview

Features ...................................................................................................... 11

3D Images ................................................................................................... 13

Using the Software..................................................................................... 17

Reading the CD-ROM Manuals............................................................... 17

Locations and Functions of Parts and Controls...................................... 18

Power Supply .................................................................................. 18

Accessory Attachments................................................................... 19

Operating and Connectors Section.................................................. 20

Monochrome LCD Panel ................................................................ 31

Viewfinder....................................................................................... 32

Viewfinder Screen Display........................................................................ 33

Chapter 2 : Preparations

Preparing a Power Supply ........................................................................ 37

Using a Battery Pack....................................................................... 37

Using AC Power ............................................................................. 38

Attaching the Viewfinder .......................................................................... 38

Attaching the Supplied Viewfinder................................................. 38

Adjusting the Viewfinder Position.................................................. 39

Adjusting the Viewfinder Angle..................................................... 39

Lifting Up the Viewfinder Barrel and Eyepiece ............................. 39

Adjusting the Viewfinder Focus and Screen................................... 41

Using the BKW-401 Viewfinder Rotation Bracket ........................ 41

Attaching a CBK-VF01 Viewfinder ............................................... 42

Attaching a 5-inch Electronic Viewfinder ...................................... 43

Setting the Area of Use.............................................................................. 44

Setting the Date/Time of the Internal Clock ........................................... 45

Preparing the Audio Input System .......................................................... 45

Connecting a Microphone to the MIC IN Connector...................... 45

Connecting Microphones to the AUDIO IN Connectors................ 46

Table of Contents

5

Attaching a UHF Portable Tuner (for a UHF Wireless Microphone

System) ..................................................................................... 47

Tripod Mounting ....................................................................................... 48

Connecting a Video Light ......................................................................... 49

Using the Shoulder Strap .......................................................................... 49

Adjusting the Shoulder Pad Position ....................................................... 50

Chapter 3 : Adjustments and Settings

Setting the Video Format .......................................................................... 51

Changing the Video Format............................................................ 52

Selecting 3D or 2D Mode........................................................................... 52

Selecting 3D or 2D.......................................................................... 52

Adjusting the Black Balance and the White Balance............................. 53

Adjusting the Black Balance........................................................... 53

Adjusting the White Balance .......................................................... 54

Setting the Electronic Shutter................................................................... 56

Shutter Modes ................................................................................. 56

Selecting the Shutter Mode and Shutter Speed............................... 56

Adjusting the Iris ....................................................................................... 58

Changing the Adjustment Mode ..................................................... 58

Adjusting the Iris using the IRIS Dial............................................. 58

Adjusting the Iris using Automatic Iris Adjustment ....................... 58

Changing the Reference Value for Automatic Iris Adjustment...... 58

Zooming ...................................................................................................... 59

Using the ZOOM Dial..................................................................... 59

Using the Zoom Lever .................................................................... 59

Adjusting the Focus ................................................................................... 60

Adjusting in MF Mode.................................................................... 60

Adjusting in AF Mode .................................................................... 61

Adjusting the Convergence....................................................................... 61

Adjusting using the CONVERGENCE Dial................................... 61

Adjusting using the AUTO CONVERGENCE Button................... 62

Adjusting using the Assignable Switches ....................................... 62

Changing the Viewfinder Display ............................................................ 62

Adjusting the Audio Level ........................................................................ 63

Manually Adjusting the Audio Levels of the Audio Inputs from the

AUDIO IN CH-1/CH-2 Connectors ......................................... 63

Manually Adjusting the Audio Level of the MIC IN Connector.... 63

Recording Audio on Channels 3 and 4 ........................................... 64

Table of Contents

6

Setting the Time Data................................................................................ 65

Setting the Timecode....................................................................... 65

Setting the User Bits........................................................................ 66

Synchronizing the Timecode........................................................... 66

Checking Camcorder Settings and Status Information

(Status Screens).................................................................................... 68

Chapter 4 : Shooting

Handling SxS Memory Cards................................................................... 70

About SxS Memory Cards .............................................................. 70

Loading and Ejecting SxS Memory Cards...................................... 71

Selecting the SxS Memory Card to Use.......................................... 72

Formatting (Initializing) SxS Memory Cards ................................. 73

Checking the Remaining Recording Time...................................... 73

Restoring SxS Memory Cards......................................................... 74

Basic Operations ........................................................................................ 75

Playing Recorded Clips................................................................... 76

Deleting Recorded Clips ................................................................. 77

Advanced Operations ................................................................................ 77

Recording Shot Marks..................................................................... 77

Setting OK Marks ........................................................................... 77

Starting to Record from Pre-stored Video (Picture Cache Function)

(2D mode only)......................................................................... 78

Recording Time-lapse Video (Interval Rec Function).................... 79

Shooting Stop Motion Animations (Frame Rec Function) ............. 80

Shooting with Slow & Quick Motion ............................................. 82

Framing Shots with the Freeze Mix Function................................. 83

Planning Metadata Operations ................................................................ 84

Loading a Planning Metadata File into Camcorder’s

Internal Memory ....................................................................... 84

Defining Clip Names in Planning Metadata ................................... 85

Defining Shot Mark Names in Planning Metadata ......................... 86

3D Shooting Guide Function..................................................................... 87

Displaying the Subject Distance Range .......................................... 87

Displaying 3D Depth Warning........................................................ 87

Displaying the Grid......................................................................... 88

Table of Contents

7

Chapter 5 : Clip Operations

Clip Playback ............................................................................................. 89

Thumbnail Screen ........................................................................... 89

Playing Clips ................................................................................... 91

Using Thumbnails to Search Inside Clips....................................... 92

Thumbnail Operations .............................................................................. 93

THUMBNAIL Menu Configuration............................................... 93

Basic THUMBNAIL Menu Operations.......................................... 94

Changing the Thumbnail Screen Type............................................ 94

Displaying Clip Properties .............................................................. 95

Adding and Deleting OK Marks ..................................................... 96

Copying Clips ................................................................................. 96

Deleting Clips.................................................................................. 97

Displaying the Expand Thumbnail Screen...................................... 98

Displaying the Shot Mark Thumbnail Screen................................. 98

Adding and Deleting Shot Marks.................................................... 99

Changing Clip Index Pictures ......................................................... 99

Chapter 6 : Menu and Detailed Settings

Setup Menu Organization and Levels.................................................... 100

Setup Menu Organization ............................................................. 100

Setup Menu Levels........................................................................ 100

Basic Setup Menu Operations ................................................................ 101

Menu List.................................................................................................. 104

OPERATION Menu...................................................................... 104

PAINT Menu................................................................................. 122

MAINTENANCE Menu ............................................................... 127

FILE Menu.................................................................................... 140

Assigning Functions to Assignable Switches ......................................... 142

Functions that can be Assigned to the ASSIGN. 0 Switch ........... 142

Functions that can be Assigned to the ASSIGN. 2 Switch ........... 143

Functions that can be Assigned to the ASSIGN. 1 and 3 Switches,

the ASSIGNABLE 4 and 5 Switches, and the COLOR TEMP.

Button...................................................................................... 143

Functions that can be Assigned to the ASSIGN. 6 Switch ........... 145

Functions that can be Assigned to the RET Button ...................... 145

Assigning Functions to the Lens Dials ................................................... 146

Functions that can be Assigned to the Lens Dials......................... 146

Table of Contents

8

Chapter 7 : Saving and Loading User Setting Data

Saving and Loading Settings................................................................... 147

Saving Setting Data....................................................................... 147

Loading Setting Data..................................................................... 148

Resetting a File after Changing Its Contents................................. 148

Saving and Loading Scene Files ............................................................. 149

Saving Scene Files ........................................................................ 149

Loading Scene Files ...................................................................... 149

Chapter 8 : Connecting External Devices

Connecting External Monitors ............................................................... 151

Operating Clips with a Computer.......................................................... 153

Using the ExpressCard Slot of a Computer .................................. 153

USB Connection with a Computer................................................ 153

Editing 3D Clips using MPES-3D01 ...................................................... 155

Chapter 9 : Maintenance

Testing the Camcorder............................................................................ 156

Maintenance ............................................................................................. 156

Cleaning the Viewfinder ............................................................... 156

Note about the Battery Terminal................................................... 156

Adjusting Left/Right Lens Errors.......................................................... 157

Correcting at a Single Point .......................................................... 157

Correcting at Multiple Points........................................................ 157

Adjusting the Flange Focal Length............................................... 158

Operation Warnings................................................................................ 159

Error Indication............................................................................. 159

Warning Indication........................................................................ 160

Appendix

Important Notes on Operation ............................................................... 166

Exchanging the Battery of the Internal Clock ...................................... 168

Specifications............................................................................................ 169

General.......................................................................................... 169

Camera Block................................................................................ 169

Audio Block .................................................................................. 170

Table of Contents

9

Display .......................................................................................... 170

Media Block.................................................................................. 170

Inputs/Outputs............................................................................... 170

Lens Block .................................................................................... 171

Supplied Accessories .................................................................... 171

Recommended Additional Equipment .......................................... 171

Chart of Optional Components and Accessories .................................. 173

MPEG-2 Video Patent Portfolio License............................................... 174

About Bitmap Fonts ................................................................................ 174

About OpenSSL ....................................................................................... 175

Index.......................................................................................................... 178

Foreword

10

After purchasing the PMW-TD300 Solid-State

Memory 3D Camcorder, before operating, it is

necessary to set the area of use.

(Unless this setting is made, the camcorder will

not operate.)

For details of these settings, see “Setting the Area of

Use” (page 44).

Note

Before attaching/removing optional components or

accessories to/from the PMW-TD300 (referred to as “the

camcorder”), be sure to turn the power of the camcorder

off.

Viewing 3D Video

• Viewing 3D video shot using this camcorder on

a 3D monitor can cause symptoms of

discomfort, such as eye fatigue, tiredness, or

nausea. It is recommended that you take regular

rest breaks when watching 3D video. The

duration and frequency of required rest breaks

will vary from person to person, so each person

must judge for themselves. If discomfort

occurs, stop watching 3D video until the

symptoms subside, and consult your doctor if

necessary. Also, please follow the instructions

provided with the software or the hardware

connected to the camcorder. Furthermore, the

sense of vision of young children (especially

children less than 6 years of age) is still in a

development stage. Before allowing young

children to view 3D video, please consult a

pediatrician or ophthalmologist. A responsible

adult should always supervise any children to

observe the above-mentioned precautions.

• The perception of 3D video varies depending on

the individual.

Foreword

Before Use

Features

11

Chapter 1 Overview

The camcorder is a shoulder-mount HD memory

camcorder featuring independent Left/Right,

1

/

2

-

type (diagonal 8 mm (

11

/

32

inches)), full-HD

(1920 × 1080) “Exmor” 3CMOS image sensors.

Dual, fixed lens system

Employs a dual, fixed-type lens that requires no

Left/Right-lens optical axis, angle of view, or

image quality adjustments, so you can start

shooting straight away.

Convergence control

The all-important convergence point can be

adjusted between approximately 1.2 m (lens

surface reference) and infinity for 3D image

representation. When shooting, you can align the

convergence point with the focus position using

one-button control.

Also, the inter-axial distance is a fixed 45 mm,

allowing wide-scope 3D images to be captured.

Unique triple dial operation

The camcorder employs a unique triple dial for

adjusting zoom, iris, and convergence, and which

synchronizes the operation of both the left and

right lens.

The function assigned to each dial can also be

customized.

3D shooting guide function

This displays a guide in the viewfinder of the

appropriate distance to the subject in order to

avoid viewer discomfort due to the parallax

between the left and right lens becoming too

large. It can also display a warning if the parallax

at the subject becomes too large. These allow the

shooting of more natural 3D images that can be

viewed comfortably.

Also, you can view 3D images in the viewfinder

using the naked eye, and the camcorder supports

various display formats for checking anaglyph

and other parallax.

3D image output to external devices

It is equipped with dual HD-SDI outputs, and can

output individual Left/Right image signals.

Furthermore, one output also supports 3G-SDI

for output of both left and right image signals

paired together.

3D images can also be output in side-by-side

format from HDMI and HD-SDI connectors.

SxS memory cards as recording media

The camcorder employs the high-performance

SxS memory cards used in XDCAM EX-series

equipment as the storage media. The left and right

images are synchronized and recorded onto two

SxS memory cards. There are four memory card

slots, two each on both the left and right, allowing

recording across two memory cards.

Approximately 6 hours of 3D images can be

recorded when loaded with four 64 GB SxS

memory cards.

Light weight, low power consumption

Design features such as CMOS image sensors,

custom video signal processing ICs, and SxS

memory card recording enable operation at power

consumption of 32 W or less. The camcorder’s

light weight (5.5 kg (12 lb 2 oz)) and low center

of gravity make it easy to carry on the shoulder

while ensuring superior stability.

HD recording using the “MPEG-2 Long

GOP” codec

The camcorder records 1920 × 1080, 1440 ×

1080, and 1280 × 720 HD images using “MPEG-

2 Long GOP” codec compression. It offers a

choice of bit rates: either 35 Mbps (HQ mode) or

25 Mbps (SP mode).

By utilizing an efficient compression format, the

camcorder records high-quality HD images for

long recording time of approx. 200 minutes at

Chapter1 Overview

Features

12

Chapter 1 Overview

35 Mbps (HQ mode) or approx. 280 minutes at

25 Mbps (SP mode) on a single 64-GB SxS

memory card.

Multi-format support

The camcorder supports interlace format

recording (1080/59.94i or 1080/50i), progressive

format recording (1080/29.97P, 1080/23.98P,

720/59.94P, 720/29.97P, 720/23.98P, or 1080/

25P, 720/50P, 720/25P), thus offering the

flexibility needed for worldwide HD recording.

(For 23.98P, native frequency recording is

possible.)

It also can output HD signals down-converted to

SD.

A variety of functions for improved

performance under various shooting

conditions

• Optical ND filters and electrical CC filters

• Hyper gamma

• Slow shutter function

• Frame Recording function

• Time lapse function (interval recording)

• Slow & quick motion function

• Freeze mix function

• Focus magnification function

• Assignable switches

• 3.5-inch high-resolution color LCD viewfinder

• Remote control

• 2D shooting mode

Wireless LAN support

You can connect this camcorder to a computer

over a wireless LAN (Wi-Fi connection) by

connecting the optional CBK-WA01 Wi-Fi

Adapter to the external device connector.

A Wi-Fi connection allows you to transfer

planning metadata from a computer to this

camcorder, and to transfer clips and other files

from this camcorder to a computer. You can also

use the Live Logging function to transfer proxy

AV data to a computer as you shoot, for logging

of the video currently being shot.

Inherits unique features of XDCAM EX

series

The camcorder inherits the workflow features of

the XDCAM EX series, including thumbnail

display and metadata management, and improves

them by introducing an improved man-machine

interface.

XDCAM EX web sites

For information on XDCAM EX, visit the

following web sites:

United States

http://www.sony.com/xdcamex

Canada

http://www.sony.ca/xdcamex

Europe, Middle East, Africa, and Russia

http://www.sonybiz.net/xdcamex

Latin America

http://www.sonypro-latin.com/xdcamex

Australia

http://www.sony.com.au/xdcamex

Asia (except Korea, China, and Japan)

http://pro.sony-asia.com

Korea

http://bp.sony.co.kr/xdcamex

China

http://pro.sony.com.cn/minisite/XDCAMEX

Japan

http://www.sony.co.jp/XDCAMEX

3D Images

13

Chapter 1 Overview

When people look at objects, the left eye and right eye view the object at a slightly different angle, and

hence the images projected in the left and right eye are different. The difference in images seen by the left

and right eye is called parallax.

By composing a picture in the head from the left and right eye images, people gain an awareness of depth

and stereoscopic effect.

3D images utilize this technique to display subjects in three dimensions. When shooting 3D images, lenses

substitute for the left eye and right eye to shoot subjects at a slightly different angle.

During playback, the right lens image is viewed by the right eye only and likewise for the left lens image,

and hence a three-dimensional subject is recognized in the minds of the viewers.

3D Images

Left eye image Right eye image

Subject recognition

3D Images

14

Chapter 1 Overview

Convergence Point

When shooting using individual left and right lenses, the point where the optical axes of the left lens and

right lens intersect is called the convergence point. The difference (parallax) between left and right images

for subjects at the convergence point is zero. During playback, subjects at the convergence point appear

to viewers to be positioned right on the screen. Subjects in front of the convergence point appear to pop

out of the screen, while subjects behind the convergence point appear to recede into the distance.

Accordingly, it is essential to set the convergence point appropriately when shooting in order to effectively

create the popping out and receding sensation during playback.

The camcorder convergence point can be adjusted in the range 1.2 m (4 ft) to ∞ (infinity). You can set the

convergence point to the focus position using a single button push, store multiple convergence points, and

recall convergence points when shooting. (see page 61)

Comfortable 3D Images

For subjects displaced from the convergence point, the parallax becomes larger as the distance from the

convergence point becomes larger. In other words, the closer the subject the more it will appear to pop

out, and the further away the more it will appear to recede into the distance. If the parallax becomes too

large, it becomes difficult for the viewer to combine the left and right images, and not only will the 3D

image appear unnatural but it may also cause eye fatigue and discomfort while viewing. Therefore, in

order to shoot comfortable 3D images for the viewer, it is essential to keep the size of parallax within an

appropriate range.

3D Images

15

Chapter 1 Overview

Parallax Guidelines

To shoot comfortable 3D images, we recommend the following points as parallax guidelines.

Parallax angle should be less than 1°

The parallax angle (

θ

) is obtained by subtracting the angle (

α

or

β

) between the left/right lenses at the

subject position from the angle (

γ

) between the left/right lenses at the convergence point, where the

optical axes of the left/right lenses intersect. The parallax angle is negative for subjects that appear to pop

out of the screen, and positive for subjects that appear to recede into the distance. The parallax angle for

comfortable 3D images is less than ±1°.

Since measuring the parallax angle is difficult when shooting, it is common to display an overlay of the

left and right images on a screen and check the size of the image mismatch (amount of parallax). When

images are viewed from a distance approximately 3 times the height of the screen, the amount of parallax

on the screen due to a parallax angle of 1° is roughly 3% of the screen width. When shooting, this guideline

translates into keeping the amount of parallax within 3% of the viewfinder screen width in order to

produce natural stereoscopic images.

Amount of parallax on the screen should not exceed space between eyes

When the amount of parallax on the screen exceeds the distance between the eyes of the viewer, it

becomes impossible to form the left and right images into a single image, making the viewer feel

discomfort. Since the space between the eyes is an individual trait, a rule of thumb is to keep amount of

parallax on the screen to less than 5 cm (2 inches). If the screen is small (77-inch type or smaller),

maintaining a parallax angle of less than 1° ensures that the amount of parallax cannot exceed 5 cm

(2 inches). However, if the screen is large (77-inch type or larger), the amount of parallax on the screen

becomes larger as the screen becomes larger, and it becomes easy to exceed the 5 cm (2 inches) guideline.

Consequently, it is important to consider the screen size when shooting.

α

Parallax angle

θ

=

γ

–

α

(or

β

)

Amount of parallax

Convergence point

3D Images

16

Chapter 1 Overview

The camcorder displays the subject distance from the camera in the viewfinder as an aid to keeping the

parallax within an appropriate range. The viewfinder can also display a colored outline of the subject as a

warning when the parallax is large and natural stereoscopic vision of the subject is difficult. You can set

the amount of parallax as a percentage of the screen width (near field, far field) or you can specify the

maximum screen size as the reference for displaying the guide functions. (see page 87)

Using the Software / Reading the CD-ROM Manuals

17

Chapter 1 Overview

The supplied CD-ROM (labeled “Utility

Software for XDCAM”) contains application and

device driver software required to access to SxS

memory cards from a computer and to manage

material shot with the camcorder.

Information about how to install the software is

provided in PDF format.

Note

You must install the SxS device driver on your computer

if your computer is equipped with an ExpressCard slot

and you want to use it to access SxS memory cards.

Preparations

The following program must be installed on your

computer in order to read the documents

contained on the CD-ROM.

Adobe Reader Version 6.0 or higher

Memo

If Adobe Reader is not installed, you can download it

from the following URL:

http://www.adobe.com/

Adobe and Adobe Reader are trademarks of Adobe

Systems Incorporated in the United States and/or other

countries.

To read the documents

Do the following:

1 Insert the CD-ROM in your CD-ROM

drive.

A cover page appears automatically in your

browser.

If it does not appear automatically in the

browser, double-click on the index.htm file

on the CD-ROM.

2 Select and click on the manual that you

wish to read.

This opens the PDF file.

Memo

The files may not be displayed properly, depending on

the version of Adobe Reader. In such a case, install the

latest version you can download from the URL

mentioned in “Preparations” above.

Note

If you have lost or damaged the CD-ROM, you can

purchase a new one to replace it. Contact a Sony service

representative.

Using the Software Reading the CD-ROM

Manuals

Locations and Functions of Parts and Controls

18

Chapter 1 Overview

a LIGHT switch

Determines how a video light connected to the

LIGHT connector (see page 19) is turned on and

off.

AUTO: When the POWER switch of the video

light is in the on position, the video light is

turned on automatically while the camcorder

is recording.

MANUAL: You can turn the video light on or off

manually, using its own switch.

Note

When the camcorder is set for recording in Picture Cache

mode, it is not possible to turn on the light before

operation to start recording is carried out (or while data

is being stored in memory).

b POWER switch

Turns the main power supply on and off.

c DC IN (DC power input) connector

(XLR type, 4-pin, male)

To operate the camcorder from an AC power

supply, connect an optional DC power cord to this

terminal and then connect the cord to the DC

output terminal of the BC-L70, BC-L160, or

another battery charger.

d DC OUT 12 V (DC power output)

connector (4-pin, female)

Supplies power for an optional WRR-860C/861/

862 UHF Synthesized Diversity Tuner

(maximum 0.5 A).

Note

Do not connect any equipment other than the UHF

synthesized diversity tuner.

e Battery attachment shoe

Attach a BP-GL95A/L80S/L60S Battery Pack.

Alternatively, you can attach an AC-DN2B/

DN10 AC Adaptor to operate the camcorder on

AC power supply.

For details, see “Preparing a Power Supply”

(page 37).

For details, see “Attaching a UHF Portable Tuner

(for a UHF Wireless Microphone System)”

(page 47).

Note

For your safety, and to ensure proper operation of the

camcorder, Sony recommends the use of the following

battery packs: BP-GL95A, BP-L60S, and BP-L80S.

Locations and Functions

of Parts and Controls

Power Supply

Locations and Functions of Parts and Controls

19

Chapter 1 Overview

a Shoulder strap fitting

Attach the supplied shoulder strap (see page 49).

b Accessory fitting shoe

Attach an optional accessory such as a video light

(see page 49).

c Viewfinder front-to-back positioning

lever

To adjust the viewfinder position in the front-to-

back direction, loosen this lever and the LOCK

knob. After adjustment, retighten this lever and

the LOCK knob.

d Viewfinder left-to-right positioning ring

Loosen this ring to adjust the left-to-right position

of the viewfinder (see page 39).

e Viewfinder fitting shoe

Attach the viewfinder.

f VF (viewfinder) connector (26-pin,

rectangular)

Connect the cable of the supplied viewfinder or

optional CBK-VF01 viewfinder.

g VF (viewfinder) connector (20-pin,

round)

Connect the cable of the optional DXF-series

viewfinder.

For connecting the DXF-series devices, optional

parts are required. Consult a Sony service

representative for information about connecting the

DXF-51 or DXF-C50W.

h Viewfinder front-to-back positioning

knob (LOCK knob)

Loosen this knob to adjust the front-to-back

position of the viewfinder (see page 39).

i Fitting for optional microphone holder

Fit an optional CAC-12 Microphone Holder (see

page 46).

j Shoulder pad

Raise the shoulder pad fixing lever to adjust the

position in the front-to-rear direction. Adjust the

position for maximum convenience when

operating the camcorder on your shoulder (see

page 50).

k LIGHT (video light) connector (2-pin,

female)

A video light with a maximum power

consumption of 50 W, such as the Anton Bauer

Ultralight 2 or equivalent can be connected (see

page 49).

l MIC IN (microphone input) (+48 V)

connector (XLR type, 5-pin, female)

Connect a stereo microphone to this connector.

The power (+48 V) is supplied via this connector.

m Tripod mount

When using the camcorder on a tripod, attach the

tripod adaptor (optional).

Accessory Attachments

Locations and Functions of Parts and Controls

20

Chapter 1 Overview

Lens Block (left side)

a VTR button

Use this to start and stop recording. Press once to

start recording, then press once more to stop.

b RET (return video) button

You can use this as an assignable switch (see

page 145).

Use this to check the video when Lens RET is

assigned to this button (factory default setting). If

you press this during recording pause, the last few

seconds recorded appear on the viewfinder screen

(recording review) (see page 75).

Pressing this button (single click) during

recording or playback records a Shot Mark 1

mark, and double-clicking records a Shot Mark 2

mark (see page 77).

c EXPAND FOCUS button

When the viewfinder display setting is L, R, or

3D, the displayed image expands, making

focusing easier (Expand Focus function).

Press the button again to return to the previous

display.

d Zoom lever

Press the W end for wide-angle and the T end for

telephoto.

Press the lever harder for a faster zoom action.

e IRIS switch

AUTO: The iris is adjusted automatically.

MANU (maual): Adjust the iris with the IRIS

dial.

f PUSH AUTO button

When the IRIS switch is in the MANU position,

press this button for an instantaneous auto

adjustment. The iris is automatically adjusted

while the button is held down.

g REMOTE FOCUS connector

Connects to an optional focus demand for focus

remote control operation.

h REMOTE ZOOM connector

Connects to an optional zoom demand for zoom

remote control operation.

i REMOTE CONVERGENCE

connector

Connects to an optional convergence demand for

convergence remote control operation.

Operating and Connectors Section

Page is loading ...

Sony PMW-TD300 Operating instructions

Related papers

Other documents