Dell POWERCONNECT 5524 Owner's manual

POWERCONNECT 5524
Dell
Brand
Dell
Model
POWERCONNECT 5524
Type
Owner's manual

This manual is also suitable for

CLI Transition Guide for
Dell™ PowerConnect™ 5500
Series Switches
A Dell Technical White Paper
www.dell.com │ support.dell.com
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page ii
THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL
ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS OR
IMPLIED WARRANTIES OF ANY KIND.
© 2011 Dell Inc. All rights reserved. Reproduction of this material in any manner whatsoever without
the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.
Dell, the DELL logo, the DELL badge, and PowerConnect, are trademarks of Dell Inc. Other trademarks
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names
other than its own.
PC5524, PC5524P, PC5548, PC5548P
Rev. A00
March 2011
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 1
Contents
Introduction ................................................................................................................ 2
Changes to the Interface Naming Conventions ....................................................................... 2
VLAN Enhancements ...................................................................................................... 2
Shadow VLAN Configuration .......................................................................................... 2
Adding a port which is a VLAN member to a LAG ................................................................. 2
Configuring IP Address on a port which is a member of VLANs ................................................. 2
Enhanced functionality in Trunk mode ............................................................................. 3
Enhancement to IGMP Snooping ........................................................................................ 3
Additional ACL Options ................................................................................................... 3
Modification in Power-Over-Ethernet .................................................................................. 3
Enhancement to Stack Configuration .................................................................................. 3
Enhancement to QoS Ingress Rate Limit ............................................................................... 3
Updated Commands – Operational Modifications .................................................................... 4
Updated Commands – Command Mode Modifications ............................................................... 6
Updated Commands – Syntax Modifications ........................................................................... 8
Summary .................................................................................................................. 13
Tables
Table 1. Updated Commands with Operational Modifications ................................................ 4
Table 2. Updated Commands with Command Mode Modifications ........................................... 6
Table 3. Updated Commands with Syntax Modifications ....................................................... 8
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 2
Introduction
The Dell™ PowerConnect™ 5500 Series Systems CLI Transition Guide White Paper outlines the changes in
the CLI commands from the PowerConnect 54XX and 35XX software to the 4.x software release on the
5500 Series switches. Changes include syntax and functional updates as specified in the following
sections.
Changes to the Interface Naming Conventions
On the Dell PowerConnect 5500, the interface naming convention is the industry standard format of
interface type (gigabitethernet or tengigabitethernet), unit ID, Slot number and port number. The user
can also use the short form of the interface type (gi or te). For example, the name of first
gigabitethernet port of unit ID 2 is: gi2/0/1 or gigabitethernet2/0/1.
VLAN Enhancements
The configuration of VLANs in this software release is much more flexible than previous releases:
Shadow VLAN Configuration
In previous products, the user could configure interface level VLAN commands only if they matched
current port’s VLAN mode. For example, if port is in access mode, user could not configure commands
related to general mode.
On the Dell PowerConnect 5500, the user can configure any VLAN command, even if not related to the
current port VLAN mode. Configuration of inactive VLAN modes are kept as “shadow configuration”
until the relevant mode is applied. The user can view shadow and active configurations via the “show
interface switchport” command.
Adding a port which is a VLAN member to a LAG
In previous products, the user could not add a port to a LAG if the port was a member in any VLAN
besides the default VLAN.
On the Dell PowerConnect 5500, the user can add a port to a LAG even if it is a member of one or more
VLANs. The VLAN configuration on the port becomes inactive until the port is removed from LAG, since
the Port acquires the VLAN configuration of the LAG. The user can view this information via the “show
interface switchport” command.
Configuring IP Address on a port which is a member of VLANs
In previous products, the user could configure an IP Address on a port only if the port was not a
member of any VLAN besides the default VLAN. IP configuration would become active immediately
after command execution.
On the Dell PowerConnect 5500, the user can define an IP Address on a port even if it is a member of
one or more VLANs. To activate IP Interface on a port, the user must apply the CLI command “no
switchport”, which enables L3 capabilities on a port. The user can view this information via “show
interface switchport” command.
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 3
Enhanced functionality in Trunk mode
On the Dell PowerConnect 5500, ports set to Trunk mode now carries all VLANs (by default) that are
created and active on the device, and an inactive member of VLANs that were not created. The port
PVID (native VLAN) can be configured to a VLAN that does not exist on the device. Untagged frames
will be classified to the VLAN whose VID is configured as the port’s PVID. Frames to all other VLANs
active on the port will be sent tagged.
Enhancement to IGMP Snooping
IGMP Snooping configuration was modified to an industry standard configuration, which includes:
robustness, query-interval, query-max-response-time, last-member-query-count and last-member-
query-interval. In the Dell PowerConnect 5500, the IGMP Snooping timers are automatically exported
from the received queries and the user does not need to configure them manually.
Additional ACL Options
The enhancement to ACLs includes support for time-based ACLs, and support for logging information on
packets dropped due to deny rules. On the Dell PowerConnect 5500, the user can configure IPv6 rules,
in addition to the IPv4 rules and MAC rules.
Modification in Power-Over-Ethernet
In previous products, the power limit was based on the Class Mode of the powered device.
On the Dell PowerConnect 5500, the user has control of the allocated power per port.
Enhancement to Stack Configuration
On the Dell PowerConnect 5500, configuring the stack unit numbers is more intuitive and the automatic
numbering feature for each unit is enabled by default.
Enhancement to QoS Ingress Rate Limit
On the Dell PowerConnect 5500, the ingress rate limit is based on the Policer mechanism, which makes
it much more accurate than in the previous products, and also makes it possible to use ingress rate
limit and storm control on a the same port.
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 4
Updated Commands – Operational Modifications
Table 1 shows the list of commands with updated syntax for normal switch operation.
Table 1. Updated Commands with Operational Modifications
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Comments
ACL {deny | permit } {any|
protocol} {any | source
source-wildcard}
{any|{destination
destination-wildcard}}
[dscp number | ip-
precedence number]
{deny | permit } {ip |
protocol } {any | source
source-wildcard} {any |
destination destination-
wildcard} [dscp number |
precedence number]
[time-range time-range-
name]
1. The command syntax was
modified
2. See also description in
previous chapter.
Address
Table
clear bridge
clear mac-addresses
{ethernet interface |
port-channel port-
channel-number}
clear mac address-table
dynamic [ interface
interface-id]
The command syntax was
modified. The revised
command aggregates two
commands in the former
implementation
IGMP
Snooping
ip igmp snooping host-
time-out
ip igmp snooping mrouter-
time-out
ip igmp snooping leave-
time-out
ip igmp robustness
ip igmp query-interval
ip igmp query-max-
response-time
ip igmp last-member-
query-count
ip igmp last-member-
query-interval
1. See description in previous
chapter.
2. The transformation to the
new implementation is as
follows under the “interface
VLAN” configuration:
RouterTimeOut = Robustness *
QueryInterval
HostTimeOut = RouterTimeOut
+ QueryMaxResponseTime
LeaveTimeOut =
LastMemberQueryCount *
LastMemberQueryInterval
Interface
Configuration
interface ethernet
interface
interface range ethernet {
port-range | all }
interface port-channel
port-channel-number
interface interface-id
interface {port-range-list
| all}
1. The command syntax was
modified
2. See also description in
previous chapter.
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 5
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Comments
ARP arp timeout seconds arp timeout seconds In the revised
implementation, the command
is supported in both Global
Configuration Mode and
Interface Configuration Mode,
while previous implementation
supported only Global
Configuration Mode.
VLAN vlan vlan-id
name
vlan vlan-id [media
ethernet] [name vlan-
name] [state active] [stp
type ieee]
1. In the revised
implementation, the command
is also used for assigning a
name to a VLAN.
2. Optional parameters were
added (entering them has no
effect)
VLAN switchport trunk allowed
vlan {add vlan-list |
remove vlan-list}
switchport trunk allowed
vlan { all | none | add
vlan-list | remove vlan-
list | except vlan-list }
1. The command syntax was
modified
2. See also description in
previous chapter.
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 6
Updated Commands – Command Mode Modifications
Table 2 shows the list of commands with updated syntax for command mode switch operation.
Table 2. Updated Commands with Command Mode Modifications
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Comments
IGMP
Snooping
ip igmp snooping ip igmp snooping vlan
vlan-id
In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
IGMP
Snooping
ip igmp snooping mrouter
learn-pim-dvmrp
ip igmp snooping vlan
vlan-id mrouter learn pim-
dvmrp
1. In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
2. The command syntax was
modified
IGMP
Snooping
ip igmp snooping mrouter
ports {add | delete}
{ethernet interface-list |
port-channel port-
channel-number-list}
ip igmp snooping vlan
vlan-id mrouter interface
interface-range-list
no ip igmp snooping vlan
vlan-id mrouter interface
interface-range-list
1. In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
2. The command syntax was
modified
IGMP
Snooping
ip igmp snooping vlan
vlan-id immediate-leave
ip igmp snooping vlan
vlan-id immediate-leave
In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 7
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Comments
IGMP
Snooping
ip igmp snooping
forbidden mrouter ports
{add | delete} {ethernet
interface-list | port-
channel port-channel-
number-list}
ip igmp snooping vlan
vlan-id forbidden mrouter
ports interface-range-list
no ip igmp snooping vlan
vlan-id forbidden mrouter
ports [interface-range-
list]
1. In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
2. The command syntax was
modified
IGMP
Snooping
ip igmp snooping
multicast-tv vlan vlan-id
{add | remove} ip-
multicast-address [count
number]
ip igmp snooping vlan
vlan-id multicast-tv ip-
multicast-address [count
number]
no ip igmp snooping vlan
vlan-id multicast-tv [ip-
multicast-address [count
number]]
1. In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
2. The command syntax was
modified
IGMP
Snooping
ip igmp snooping querier
enable
ip igmp snooping vlan
vlan-id querier
no ip igmp snooping vlan
vlan-id querier
1. In Dell PowerConnect 5500,
the command was modified
from VLAN Interface
Configuration Mode command
to Global Configuration Mode
command that includes the
VLAN ID as a parameter
2. The command syntax was
modified
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 8
Updated Commands – Syntax Modifications
Table 3 shows the list of commands with updated syntax modifications.
Table 3. Updated Commands with Syntax Modifications
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
802.1x dot1x timeout re-authperiod
seconds
dot1x timeout reauth-period
seconds
802.1x dot1x re-authentication dot1x reauthentication
802.1x dot1x multiple-hosts dot1x host-mode {single-host
| multi-host}
802.1x dot1x single-host-violation
{discard | forward | discard-
shutdown}
dot1x violation-mode {protect
| forward | shutdown}
AAA enable password [ level level
] password [encrypted]
enable password [level level]
[[password | {{0 | 7}
encrypted-password}]
AAA username name [password
password] [level level]
[encrypted]
username name [privilege
level] [[password | {{0 | 7}
encrypted-password}]
AAA aaa accounting login {radius} aaa accounting login start-
stop group radius
AAA aaa accounting dot1x
{radius}
aaa accounting dot1x default
start-stop group radius
ACL ip access-list access-list-
name
ip access-list extended name
ACL mac access-list access-list-
name
mac access-list extended
name
Address Table bridge aging-time seconds mac address-table aging-time
seconds
Clock commands clock timezone hours
minutes zone
clock timezone zone hours-
offset [minutes-offset]
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 9
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Clock commands
clock summer-time [usa|eu]
recurring | date zone
clock summer-time zone
recurring {usa | eu | {week
day month hh:mm week day
month hh:mm}} [offset]
clock summer-time zone date
date month year hh:mm date
month year hh:mm [offset]
clock summer-time zone date
month date year hh:mm
month date year hh:mm
[offset]
Ethernet
configuration
clear counters [ethernet
interface | port-channel
port-channel-number]
clear counters interface-id
Ethernet
configuration
port storm-control broadcast
rate rate
storm-control broadcast level
bps rate
IP Addressing renew dhcp {ethernet
interface-number | vlan
vlan-id | port-channel
number}
renew dhcp interface-id
IP Addressing arp ip_addr hw_addr
{ethernet interface-number
| vlan vlan-id | port-channel
number}
arp ip-address hardware-
address {interface-id}
IP Addressing ip domain-name name ip domain name name
IP Addressing ipv6 address ipv6-address
link-local
ipv6 address ipv6-
address/prefix-length link-
local
IP Addressing ipv6 neighbor ipv6-addr hw-
addr {ethernet interface-
number | vlan vlan-id | port-
channel number}
ipv6 neighbor ipv6-addr
interface-type interface-
number hw-addr
IP Addressing tunnel source {auto | ip-
address ipv4-address }
tunnel source {auto |ipv4-
address }
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 10
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Web server ip http exec-timeout minutes
[seconds]
ip http timeout-policy idle
seconds
Web server ip http authentication
method1 [method2...]
ip http authentication aaa
login-authentication method1
[method2...]
Web server ip https port ip http secure-port
Web server ip https server ip http secure-server
Port channel port-channel load-balance
{layer-2-3 | layer-2 | layer-3
| layer-2-3-4}
port-channel load-balance
{src-dst-mac | src-dst-ip | src-
dst-mac-ip | src-dst-mac-ip-
port}
LLDP lldp enable lldp run
LLDP lldp enable [rx | tx | both] lldp transmit
lldp receive
LLDP lldp hold-multiplier number lldp holdtime seconds
LLDP lldp reinit-delay seconds lldp reinit seconds
LLDP clear lldp rx [ethernet
interface]
clear lldp table [interface-id]
RMON rmon collection history index
[owner name | buckets
bucket-number | interval
interval]
rmon collection stats index
[owner name | buckets
bucket-number | interval
interval]
SNMP no snmp-server enable no snmp-server
SNMP snmp-server host { ipv4-
address | ipv6-address|
hostname} community-string
[traps | informs] [1 | 2]
[udp-port port] [filter
filtername] [timeout
seconds] [retries retries]
snmp-server host host-addr
[informs | traps] [version {1 |
2c | 3 {auth | noauth | priv}]
{community-string
[notification-type]} [udp-port
port] [filter filtername]
[timeout seconds] [retries
retries]
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 11
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
SNMP snmp-server community
community [ro | rw | su]
[ipv4-address| ipv6-address]
[view view-name]
snmp-server community-
group community group-
name [ipv4-address| ipv6-
address]
snmp-server community
community [view view-name]
[ro | rw | su] [ipv4 address |
ipv6 address] [access-list-
number]
SNMP snmp-server user username
groupname [remote
engineid-string ] [ auth-md5
password | auth-sha
password | auth-md5-key
md5-des-keys | auth-sha-key
sha-des-keys ]
no snmp-server user
username [remote engineid-
string ]
snmp-server user username
groupname [remote engineid-
string ]
{v1 | v2c | v3 [encrypted]
[auth {md5 | sha} auth-
password]}
no snmp-server user username
[remote engineid-string ]
SSH user-key username {rsa |
dsa}
no user-key username
named-key key-name {
encryption | signature }
Spanning Tree spanning-tree mode { stp |
rstp | mstp}
spanning-tree mode { stp |
rstp | mst}
Spanning Tree spanning-tree bpduguard spanning-tree bpduguard
{enable | disable}
no spanning-tree bpduguard
Spanning Tree clear spanning-tree
detected-protocols [ethernet
interface | port-channel
port-channel-number]
clear spanning-tree detected-
protocols [interface interface-
id]
Spanning Tree instance instance-id {add |
remove} vlan vlan-range
instance instance-id vlan vlan-
range
no instance instance-id [vlan
vlan-range]
Syslog logging buffered size number logging buffered [buffer-size]
[severity-level]
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 12
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
Syslog logging {ipv4-address | ipv6-
address | hostname} [port
port] [severity level] [facility
facility] [description text]
logging host {ipv4-address |
ipv6-address | hostname}
[port port] [severity level]
[facility facility] [description
text]
System
Management
ping ip-address | hostname
[size packet_size] [count
packet_count] [timeout
time_out]
ping ip {ipv4-address |
hostname} [size packet_size]
[count packet_count]
[timeout time_out]
System
Management
traceroute {ip-
address|hostname} [size
packet_size] [ttl max-ttl]
[count packet_count]
[timeout
time_out] [source ip-
address] [tos tos]
traceroute ip {ipv4-addr |
hostname} [size packet_size]
[ttl max-ttl] [count
packet_count] [timeout
time_out] [source ip-address]
[tos tos]
System
Management
stack reload [unit]
reload [slot stack-member-
number]
System
Management
stack change unit-id unit-
number to new-unit-number
switch current-stack-member-
number renumber new-stack-
member-number
802.1x show dot1x [ethernet
interface]
show dot1x statistics
ethernet interface
show dot1x [interface
interface-id]
show dot1x statistics interface
interface-id
Address Table show mac address-table
[vlan vlan] [interface
interface-id] [address mac-
address]
show mac address-table
dynamic [vlan vlan] [interface
interface-id] [address mac-
address]
Address Table show mac address-table
[vlan vlan] [interface
interface-id] [address mac-
address]
show mac address-table static
[vlan vlan] [interface
interface-id] [address mac-
address]
Ethernet
configuration
show ports storm-control
[interface ]
show storm-control
[interface-id ]
CLI Transition guide for Dell PowerConnect 5500 Series Switches
Page 13
Feature Previous Implementation
Dell PowerConnect 5500
Implementation
System
Management
show power inline [ethernet
interface-id ]
show power inline power-
consumption [ethernet
interface-id ]
show power inline [[interface-
id | consumption ] | module
switch-number]
System
Management
show copper-ports tdr [
interface ]
show cable-diagnostics tdr
interface interface-id
System
Management
show stack [ unit unit ]
show switch [stack-member-
number]
IGMP Snooping
ip igmp snooping forbidden
mrouter ports {add | delete}
{ethernet interface-list |
port-channel port-channel-
number-list}
ip igmp snooping vlan vlan-id
forbidden mrouter ports
interface-range-list
no ip igmp snooping vlan vlan-
id forbidden mrouter ports
[interface-range-list]
Summary
For more information, consult the Dell PowerConnect 5500 CLI Guide available at
http://support.Dell.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Dell POWERCONNECT 5524 Owner's manual

POWERCONNECT 5524
Dell
Brand
Dell
Model
POWERCONNECT 5524
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers