BORLA Stainless Steel Axle Back Exhaust Kit Installation guide

Brand
BORLA
Model
Stainless Steel Axle Back Exhaust Kit
Type
Installation guide
TITLE: Jeep Wrangler Installation Instruc-
tions
PART NO. A-35367 Rev. A Page 1 of 5
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City, TN 37604-7523
805-986-8600
Installation for Jeep Wrangler
PN’s- 11755, 11834,11860,11860BC
Thank you for purchasing a Borla Performance Exhaust System.
Borla Performance Rear Section Systems PN-(11755) is designed for the Jeep Wrangler equipped with a 3.8L V6 engine, 2
and 4WD automatic or manual transmission.
Borla Performance Rear Section Systems PN’s-(11834,11860,11860BC) is designed for the Jeep Wrangler equipped with a
3.6L V6 engine, 4WD automatic or manual transmissions.
Borla Performance Industries recommends that an exhaust shop or professional after market parts installer perform the installation
of this system. However, if you decide to perform the installation on your own it is recommended that two people are used. This
installation should not be performed by one person due to the risk of injury. Ensure the installers use all under car safety precau-
tions including eye protection.
Please take time to read and understand the following…
By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms
stated below.
It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your
Borla Performance Exhaust System.
Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improp-
er operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s
products and/or systems.
Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on
your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your
new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.
These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please
read this document completely before beginning the installation of your system.
Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for
this installation.
To ensure this part number fits your specific model year, please visit our website for the latest model year listings at
www.BORLA.com.
TITLE: Jeep Wrangler Installation Instruc-
tions
PART NO. A-35367 Rev. A Page 2 of 5
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City, TN 37604-7523
805-986-8600
Minimum Required Tool List:
TOOLS:
1. 3/8” Drive Ratchet
2. 3/8” Drive Extension 3”
3. 14mm Socket
4. 15mm Deep Well Socket
5. Pry Bar
SHOP SUPPLIES:
1 Spray Lubricant
Borla Performance - Bill of Materials
11834
11755
TITLE: Jeep Wrangler Installation Instruc-
tions
PART NO. A-35367 Rev. A Page 3 of 5
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City, TN 37604-7523
805-986-8600
Minimum Required Tool List:
TOOLS:
1. 3/8” Drive Ratchet
2. 3/8” Drive Extension 3”
3. 14mm Socket
4. 15mm Deep Well Socket
5. Pry Bar
SHOP SUPPLIES:
1 Spray Lubricant
Borla Performance - Bill of Materials
11860
11860BC
TITLE: Jeep Wrangler Installation Instruc-
tions
PART NO. A-35367 Rev. A Page 4 of 5
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City, TN 37604-7523
805-986-8600
Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is
hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle.
Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Rear Section Exhaust
System.
Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old
exhaust system from your vehicle.
Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided
on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Rear Section Exhaust System.
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to
be applied liberally to all exhaust fasteners and allowing a significant
period of time for the chemical to lubricate the threads before at-
tempting to disassemble.
1. Loosen the clamp located just before the muffler assembly.
(See Fig.1&2)
2. Lubricate all the hangers and rubber isolators.
3. Using a muffler stand or an additional person to hold the
muffler assembly
4. Remove the hangers from the rubber isolators and remove
the muffler assembly from the vehicle. (See Fig. 3)
Warning: Use extreme caution during installation. Torque
all fasteners according to manufacturer’s torque values and
tightening sequence. DO NOT use air impact tools to tighten
fasteners on Borla Performance Exhaust Systems. Use of
such tools may result in bent flanges or gasket contact areas
leading to exhaust leaks.
Figure 1
Figure 2
Figure 3
TITLE: Jeep Wrangler Installation Instruc-
tions
PART NO. A-35367 Rev. A Page 5 of 5
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City, TN 37604-7523
805-986-8600
Borla Performance
Exhaust System Installation
1. Place a clamp over the expanded end of the muffler assembly
and set it into position. (See Fig.3) Do Not tighten the
clamp.
2. Place a clamp over the expanded end of the tip assembly and
set it into position as also shown. Do Not tighten the clamp.
(See Fig.4)
3. Check your exhaust system for proper clearance under the
vehicle and also for tip alignment. (See Fig.5)
4. Once position has been determined to be correct, tighten the
Accuseal™ clamps to 32-35 ft. lbs. making sure the clamp
opening is not over any of the notches in the pipe. Before
starting your vehicle, make sure to check all wires, hoses,
brake lines, body parts and tires for safe clearance from the
exhaust system.
5. Start vehicle and check for any leaks. If any leaks are found,
determine cause (such as loose hardware or incorrectly posi-
tioned clamp) and repair as necessary.
Note: When you first start your vehicle after the in-
stallation of your new Borla Performance Exhaust
System, there may be some smoke and fumes coming
from the system. This is a protective oil based coating
used in the manufacturing of mandrel bent perfor-
mance exhaust tubing. This is not a problem and will
disappear within a very short period of time after the
exhaust has reached normal operating temperatures.
Figure 3
Figure 4
Figure 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

BORLA Stainless Steel Axle Back Exhaust Kit Installation guide

Brand
BORLA
Model
Stainless Steel Axle Back Exhaust Kit
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents