Atdec telehook TH-2050-VFM User manual
- Category
- Flat panel desk mounts
- Type
- User manual
This manual is also suitable for
Installation Instructions
TH-2050-VFM
Components Checklist
Flat Screen Wall Mount | Full Motion
TOOLS REQUIRED:
Hardware
Mounting Screws
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.
Step 1. Check Components
Step 2. Locate Drilling Position
Top
Step 3. Attaching the Articulated Arm to the Wall
Timber Stud Wall
Masonry Wall
Wall
OR
Only use the Extension Plates if the Display you wish to mount has a VESA hole configuration:
400x200mm, 400x300mm, 400x400mm. If not, skip to Step 5. A
AB
B
TIGHTEN
FIRMLY
Dome Nut
Extension Plate
VESA Plate
Star Washer
Top of
Display
Spacer Bush (x4) optional
used for recessed mounting
holes or curved panels.
Choose appropriate Mouting Screws and Washers
from the Hardware supplied to suit your Display.
Mounting Screw (x4) Washer (x4)
VESA plate
Mounting
Hole
IMPORTANT:
Using the 4mm Allen Key
loosen (do not remove)
the Security Screw until flush
with the Quick-release Hook.
Slide the VESA plate onto
the Quick-release Hook.
VESA plate
LOOSEN
TIGHTEN
Rotate the Display into a
Horizontal position as
required.
Back of Display
+/- 5°
Security
Screw
(FLUSH)
Quick-release
Hook
Step 4. Fasten Extension Plates to the VESA Plate (optional)
400x400mm
Step 6. Attaching your Display to the Articulated Arm
Tighten the Security
Screw fully to lock.
Step 5. Attaching the VESA Plate to your Display
Step 7. Cable Management
Remove Cable Covers using a Phillips Head Screwdriver, and route the cables
along the length of the arms. Reattach the Cable Covers to hold the Cables in place.
Cable Covers
Clamp
Lever
Tighten the Clamp Lever to lock
the Display in desired position.
TILT DOWN
TILT UP
TIP: Leave enough slack in the cables
to allow full movement at the joints.
Cable Covers
Step 8. Tilt Adjustment
Installation Complete
BA
A
B
400x200mm
BA
AB
400x300mm
OR OR
Connect cables to your Display and route through Cable Clips.
As TFT Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 08.06.10 ©
LOOSEN
TIGHTEN
Release the Clamp Lever and tilt the Display up or down as desired.
PULL
TO RESET
TIP: If the Clamp
Lever is obstructed
pull it outwards to
disengage the
rachet mechanism.
Cable Clips
-
1
-
2
Atdec telehook TH-2050-VFM User manual
- Category
- Flat panel desk mounts
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Atdec AC-AP-4040 Installation guide
-
-
Atdec TH-2050-VFM Specification
-
Atdec TH-2050-UFL Installation guide
-
Atdec TH-3270-UFM User guide
-
Atdec TH-1040-VFM User manual
-
-
-
-
Other documents
-
PERLESMITH PSMFK1 Installation guide
-
MOUNTUP MU0037 User manual
-
MOUNTUP MU0014-B Installation guide
-
PERLESMITH PSMFK6 Installation guide
-
Peerless FPE55FH-UK-S Datasheet
-
Vivo MOUNT-AD400B User manual
-
-
Mount Plus 4330178939 User guide
-
Cheetah APTMM2B User manual
-
