HiB Polar Fitting Instructions

Brand
HiB
Model
Polar
Type
Fitting Instructions

This manual is also suitable for

LED Ceiling Lights
Polar Art No. 0720
Horizon Art no. 0730
Lumen Art no. 0740
Thank you for purchasing this HiB
product.
Please read through these instructions
carefully and refer back to them during
installation to ensure that your product
is fitted safely and that it retains its high
quality finish.
FI#04 015 R211007 Ver No. 1.0 Oct 2021
All installations must comply with guidelines which are based on a zonal concept. The diagram above illustrates this concept and must
be followed to ensure the safe installation of electrical appliances in the bathroom. These regulations apply to domestic installations
only. Installations must be made in accordance with the current IEE wiring regulations and relevant building regulations. HiB
recommends that all electrical bathroom products should only be fitted by a suitably qualified, Part P registered electrician.
(Fig. 1)
Fitting Instruction
Ensure the domestic electrical mains supply to which the ceiling light is being connected is turned off.
1. Position the ceiling light in a suitable location (according to the zonal diagram above (Fig. 1), ensuring
that the domestic electrical mains supply is within reach of the electrical entry point of the product.
2. Carefully mark the position of the ceiling light mounting points using a so pencil. Please ensure
that all marked mounting points accurately match up with the fixing points on the ceiling light.
3. Before drilling, ensure there are no hidden cables or pipes behind the mounting points. Using
a suitable drill bit, drill holes in the marked positions to a suitable depth.
4. Insert wall plugs level with the surface of the ceiling. NB. For plasterboard ceilings, specialist fixings
should be purchased, available from any DIY or hardware store.
5. Line up product with marked fixing points, feed mains supply through the lights base and screw into
place.
6. Ensure the domestic electrical mains supply to which the ceiling light is being connected is
turned off. Connect the domestic mains supply to the terminal block according to the wiring diagram
(Fig. 6).
7. Lumen light ONLY, connect the two electrical connectors together ensuring they do not come apart.
(Fig. 3).
8. Attach ceiling light shade and screw the shade chrome cover cap into place. (See fig.3,4 & 5)
9. Switch the domestic electrical mains supply back on.
This product is IP44 - suitable for installation in zones: 2 & Outside Zones
Please retain this leaflet for future reference.
T: +44 (0)20 8441 0352 F: +44 (0)20 8441 0219 E: [email protected].uk hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as
possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
Lumen Assembly (Fig. 3)
Horizon Assembly (Fig. 5)
Polar Assembly (Fig. 4)
Wiring Diagram (Fig. 6)
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Earth is Green and Yellow
Neutral is Blue
Care Instructions
Do not use abrasives or solvents when cleaning this
product.
Wipe off all water spillages as soon as possible using a so,
damp cloth.
Operation Instructions
This product is non-dimmable.
a
Aercare Service
In the unlikely event that this product should fail, please
contact HiB Customer Services, details shown below.
WEEE compliance
Must not be mixed with general household waste
Electrical Information
This product contains a light source of energy efficiency class E
  • Page 1 1
  • Page 2 2

HiB Polar Fitting Instructions

Brand
HiB
Model
Polar
Type
Fitting Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents