Page is loading ...
Installation instructions of display board
I. Parts list
A. 2020-Q4MKT-BK-L .............................. 1PCS
B. 2020-Q4MKT-BK-R .............................. 1PCS
C. 2020-BPTA-DR-LU_HOOK ................. 1PCS
D. 2020-BPTA-DR-RU_HOOK ................ 1PCS
E. 2020-BPTA-DR-LD_HOOK ................. 1PCS
F. 2020-BPTA-DR-RD_HOOK ................. 1PCS
G. 2020-Q4MKT-AL-1100 ...................... 4PCS
H. 2020-Q4MKT-AL-700 ........................ 2PCS
I. 2020-Q4MKT-20x20 ........................... 22SET
J. SW-SCSM4x20-BK .............................. 22PCS
K. SW-SCSM4x30-BK ............................. 10PCS
L. SW-FSCM5x16x9x1 ............................ 12PCS
M. 2020-Q4MKT-19x15 ........................ 10PCS
N. Nuts-ASM4-BK ................................... 10PCS
O. M5-Nuts-SS ......................................... 12PCS
P. 2020-Q4MKT-BET-IBM5-8 ................. 8PCS
Q. 2020-Q4MKT-BETBET-M5x8 .......... 16PCS
R. BP2019Q4MKT-USAMC ...................... 1SET
S. Bitspower logo board .......................... 1PCS
T. Color sign board .................................... 1PCS
A. 2020-Q4MKT-BK-L C. 2020-BPTA-DR-LU_HOOK
D. 2020-BPTA-DR-RU_HOOK
E. 2020-BPTA-DR-LD_HOOK
F. 2020-BPTA-DR-RD_HOOK
G. 2020-Q4MKT-AL-1100
H. 2020-Q4MKT-AL-700
I. 2020-Q4MKT-20x20
J. SW-SCSM4x20-BK
L. SW-FSCM5x16x9x1
M. 2020-Q4MKT-19x15
N. Nuts-ASM4-BK
O. M5-Nuts-SS
K. SW-SCSM4x30-BK
P. 2020-Q4MKT-BET-IBM5-8
Q. 2020-Q4MKT-BETBET-M5x8
R. BP2019Q4MKT-USAMC
S. Bitspower logo board
T. Color sign board
B. 2020-Q4MKT-BK-R
Installation instructions of display board
II. Installation instructions
P. 2020-Q4MKT-BET-IBM5-8
STEP 1
TIPS: This part is directional in use. Please follow
the direction shown in the figure when installing.
G. 2020-Q4MKT-AL-1100
H. 2020-Q4MKT-AL-700
Q. BET M5 X 8
H. 2020-Q4MKT-AL-700
1. Slide 4 PCS P. into the 1 PCS H.
groove and roughly distribute them.
2. Connect all Supporting rod.
G. 2020-Q4MKT-AL-1100
3. Use 2 PCS Q. for each P. to lock,but
do not lock completely temporarily, so
that G. can slide.
TIPS: This part is directional in use. Please follow
the direction shown in the figure when installing.
（The red side is the thicker side.）
I. 2020-Q4MKT-20x20
4. Place the block in the G. or H. slot,
then rotate it 90 degrees.
5. Roughly distribute the set I. as shown in the figure, and rotate all the set I. to the same direction.
STEP 2
1. Align the upper and lower edges of the A. and B. , and then close them together.
Square nut
I.
A. 2020-Q4MKT-BK-L B. 2020-Q4MKT-BK-R
the set I.
2. Adjust the position of the support rod and the block to align the screw hole position.
Then, tighten the screws of Step 1-3 that are not fully locked.
3.Locking screw, combining backplane and support bracket.
4.Install the hook to the backplane according to the position.
J. SW-SCSM4x20-BK
L. SW-FSCM5x16x9x1
O. M5-Nuts-SS
C. 2020-BPTA-DR-LU_HOOK
D. 2020-BPTA-DR-RU_HOOK
E. 2020-BPTA-DR-LD_HOOK
F. 2020-BPTA-DR-RD_HOOK
STEP 3
R. BP2019Q4MKT-USAMC
TIPS: The wires in the set R. have been arranged to the back. Before installation, please put the wires through the
center hole of the backblane.
WIRES
1. Lock the set R. on the backplane.
M. 2020-Q4MKT-19x15
N. Nuts-ASM4-BK
K. SW-SCSM4x30-BK
2. Stick the S. and T. onto the backplane,and then complete the installation.
S. Bitspower logo board
T. Color sign board
/
