AGI HCX2 Transfer Assembly Manual

Read this manual before using product. Failure to

follow instructions and safety precautions can

result in serious injury, death, or property

damage. Keep manual for future reference.

Part Number: P1512157 R0

Revised: November 2018

Transfer

Portable Grain Belt Conveyor

Assembly Manual

This manual applies to the following brands and models:

Batco BCX2, Westfield WCX2, Hutchinson HCX2:

1500 Series: 1515

Original Instructions

2 P1512157 R0

TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 3

CONTENTS

1. Safety....................................................................................................................................................... 4

1.1. Safety Alert Symbol and Signal Words..................................................................................... 4

1.2. General Product Safety ............................................................................................................ 4

1.3. Moving Conveyor Belt Safety................................................................................................... 5

1.4. Rotating Parts Safety................................................................................................................ 5

1.5. Drives and Lockout Safety........................................................................................................ 5

1.5.1 Gas Engine Safety....................................................................................................... 6

1.5.2 Electric Motor Safety.................................................................................................. 6

1.5.3 Hydraulic Power Safety .............................................................................................. 7

1.6. Tire Safety................................................................................................................................. 8

1.7. Personal Protective Equipment................................................................................................ 8

1.8. Safety Equipment ..................................................................................................................... 9

1.9. Safety Decals ............................................................................................................................ 9

1.9.1 Decal Installation/Replacement................................................................................. 9

1.9.2 Safety Decal Locations and Details ............................................................................ 9

2. Features................................................................................................................................................. 17

3. Assembly ............................................................................................................................................... 18

3.1. Assembly Safety ..................................................................................................................... 18

3.2. Check Shipment...................................................................................................................... 18

3.3. Required Tools........................................................................................................................ 18

3.4. Before You Begin .................................................................................................................... 19

3.5. Hydraulic Fittings and Bolt Tightening ................................................................................... 19

3.6. Component Locations ............................................................................................................ 19

3.7. Connect the Conveyor Tube to the Hopper .......................................................................... 20

3.8. Serial Number Decal Placement ............................................................................................ 22

3.9. Install the Spout Roller and Hex Roller .................................................................................. 23

3.10. Install the Hopper Latch Hardware...................................................................................... 25

3.11. Install the Belt ...................................................................................................................... 26

3.12. Attach the Hopper Underside Covers .................................................................................. 31

3.13. Install the Collapsible Hopper Cloth .................................................................................... 33

3.14. Attach the Hitch ................................................................................................................... 39

3.15. Install the Spout Hood.......................................................................................................... 40

3.16. Install the Collapsible Hopper Cloth Controls...................................................................... 41

3.17. Assemble the Frame............................................................................................................. 44

3.18. Drive Assemblies .................................................................................................................. 45

3.18.1 Install the Electric Drive ......................................................................................... 45

3.18.2 Install the Hydraulic Drive...................................................................................... 53

3.18.3 Install the Gas Drive ............................................................................................... 57

3.19. Install the Shaft Guard ......................................................................................................... 64

3.20. Install the Manual Container ............................................................................................... 65

4. Specifications ........................................................................................................................................ 66

5. Appendix ............................................................................................................................................... 67

5.1. Bolt Torque............................................................................................................................. 67

5.2. Fittings Torque Values............................................................................................................ 68

4 P1512157 R0

1. Safety

1.1. Safety Alert Symbol and Signal Words

This safety alert symbol indicates important safety messages in this manual. When you see

this symbol, be alert to the possibility of injury or death, carefully read the message that

follows, and inform others.

Signal Words: Note the use of the signal words DANGER,WARNING,CAUTION, and NOTICE with the safety

messages. The appropriate signal word for each message has been selected using the definitions below as a

guideline.

Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or

death.

Indicates a hazardous situation that, if not avoided, could result in serious injury or death.

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, may result in property damage.

1.2. General Product Safety

YOU are responsible for the SAFE use and maintenance of your conveyor. YOU must ensure that you and

anyone else who is going to work around the conveyor understands all procedures and related SAFETY

information contained in this manual.

Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around

you. Make these practices a working part of your safety program. All accidents can be avoided.

• It is the conveyor owner, operator, and maintenance personnel's responsibility to

read and understand ALL safety instructions, safety decals, and manuals and follow

them when operating, or maintaining the equipment.

• Owners must give instructions and review the information initially and annually with all personnel before

allowing them to operate the conveyor. Untrained users/operators expose themselves and bystanders to

possible serious injury or death.

• The conveyor is not intended to be used by children.

• Use the conveyor for its intended purposes only.

• Do not modify the conveyor in any way without written permission from the manufacturer. Unauthorized

modification may impair the function and/or safety, and could affect the life of the conveyor. Any

unauthorized modification will void the warranty.

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 5

1.3. Moving Conveyor Belt Safety

• DO NOT step on or touch moving conveyor belt.

• Shut off and lock out power to adjust, service, or clean.

1.4. Rotating Parts Safety

• Keep body, hair, and clothing away from rotating pulleys,

belts, chains, and sprockets.

• Do not operate with any guard removed or modified. Keep

guards in good working order.

• Shut off and remove key or lock out power source before

inspecting or servicing machine.

1.5. Drives and Lockout Safety

Inspect the power source(s) before using and know how to shut down in an emergency.

Whenever you service or adjust your equipment, make sure you shut down the power

source and unplug or remove the key (as applicable) to prevent inadvertent start-up and

hazardous energy release. Know the procedure(s) that applies to your equipment from the

following power source(s). Ensure that all personnel are clear before turning on power to

equipment.

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

6 P1512157 R0

1.5.1 Gas Engine Safety

Power Source

• Keep guards in place and secure.

• Properly ventilate surrounding area.

• Never fill the fuel tank with the engine running, while

smoking, or near an open flame. Always shut down and allow

engine to cool before filling with fuel.

• Never overfill the tank or spill fuel. If fuel is spilled, clean it

up immediately.

• Be sure to use the correct type and grade of fuel. Ground the

fuel funnel or nozzle against the filler neck to prevent sparks

that could ignite fuel vapors.

• Be sure to replace the fuel fill cap when you are done.

Lockout

• For engines with an electric start, remove the ignition key,

the spark plug wire, or the spark plug.

• For engines with a rope or crank start, remove the spark plug

wire or the spark plug.

1.5.2 Electric Motor Safety

Power Source

• Electric motors and controls shall be installed and serviced by

a qualified electrician and must meet all local codes and

standards.

• A magnetic starter should be used to protect your motor.

• You must have a manual reset button.

• Reset and motor starting controls must be located so that the

operator has full view of the entire operation.

• Locate main power disconnect switch within reach from

ground level to permit ready access in case of an emergency.

• Motor must be properly grounded.

• Guards must be in place and secure.

• Ensure electrical wiring and cords remain in good condition;

replace if necessary.

• Use a totally enclosed electric motor if operating in

extremely dusty conditions.

SERVICE DISCONNECT

ON

OFF

Lockout

• The main power disconnect switch should be in the locked position during shutdown or

whenever maintenance is performed.

• If reset is required, disconnect all power before resetting motor.

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 7

1.5.3 Hydraulic Power Safety

Power Source

• Refer to the rules and regulations applicable to the power

source operating your hydraulic drive.

• Do not connect or disconnect hydraulic lines while system is

under pressure.

• Keep all hydraulic lines away from moving parts and pinch

points.

• Escaping hydraulic fluid under pressure will cause serious

injury if it penetrates the skin surface (serious infection or

toxic reaction can develop). See a doctor immediately if

injured.

• Use metal or wood as a backstop when searching for

hydraulic leaks and wear proper hand and eye protection.

• Check all hydraulic components are tight and in good

condition. Replace any worn, cut, abraded, flattened, or

crimped hoses.

• Clean the connections before connecting to equipment.

• Do not attempt any makeshift repairs to the hydraulic fittings

or hoses with tape, clamps, or adhesive. The hydraulic

system operates under extremely high pressure; such repairs

will fail suddenly and create a hazardous and unsafe

condition.

Lockout

• Always place all hydraulic controls in neutral and relieve

system pressure before disconnecting or working on

hydraulic system.

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

8 P1512157 R0

1.6. Tire Safety

Failure to follow proper procedures when mounting a tire on a

wheel or rim can produce an explosion that may result in

serious injury or death.

• DO NOT attempt to mount a tire unless you have the proper

equipment and experience to do the job.

• Have a qualified tire dealer or repair service perform

required tire maintenance.

• When replacing worn tires, make sure they meet the original

tire specifications. Never undersize the replacement tire.

• DO NOT weld to the tire rim with the tire mounted on the

rim. This action may cause an explosion which could result in

serious injury or death.

• Inflate tires to the manufacturer’s recommended pressure.

• Tires should not be operated at speeds higher than their

rated speed.

• Keep wheel lug nuts tightened to manufacturer’s

recommendations.

• Never reinflate a tire that has been run flat or seriously

under-inflated without removing the tire from the wheel.

Have the tire and wheel closely inspected for damage before

remounting.

1.7. Personal Protective Equipment

The following Personal Protective Equipment (PPE) should be worn when assembling the equipment.

Safety Glasses

• Wear safety glasses at all times to protect eyes from debris.

Work Gloves

• Wear work gloves to protect your hands from sharp and rough edges.

Steel-Toe Boots

• Wear steel-toe boots to protect feet from falling debris.

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 9

Coveralls

• Wear coveralls to protect skin.

Hard Hat

• Wear a hard hat to help protect your head.

1.8. Safety Equipment

The following safety equipment should be kept on site:

Fire Extinguisher

• Provide a fire extinguisher for use in case of an accident. Store in a highly visible and

accessible place.

First-Aid Kit

• Have a properly-stocked first-aid kit available for use should the need arise, and

know how to use it.

1.9. Safety Decals

• Keep safety decals clean and legible at all times.

• Replace safety decals that are missing or have become illegible. See decal location figures that follow.

• Replaced parts must display the same decal(s) as the original part.

• Replacement safety decals are available free of charge from your distributor, dealer, or factory as applicable.

1.9.1 Decal Installation/Replacement

1. Decal area must be clean and dry, with a temperature above 50°F (10°C).

2. Decide on the exact position before you remove the backing paper.

3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing

in place.

4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place.

5. Small air pockets can be pierced with a pin and smoothed out using the sign backing paper.

1.9.2 Safety Decal Locations and Details

Replicas of the safety decals that are attached to the conveyor and their messages are shown in the figure(s)

that follow. Safe operation and use of the conveyor requires that you familiarize yourself with the various safety

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

10 P1512157 R0

decals and the areas or particular functions that the decals apply to, as well as the safety precautions that must

be taken to avoid serious injury, death, or damage.

Figure 1. Safety Decal Locations

P1513045

P15130001

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 11

Figure 2. Electric Top Drive Safety Decal Locations

* behind guard

Figure 3. Hydraulic Top Drive Safety Decal Locations

P1513008*

P1513002

P1513009

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

12 P1512157 R0

Figure 4. Gas Top Drive Safety Decal Locations

* behind guard

P1513008*

P1513002

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 13

Table 1. Safety Decals

Part Number Description

P1513052

To prevent damage, wheels must be

free to move when raising or lowering

equipment.

When equipment is positioned, chock

all wheels.

NOTICE

P1513037

To prevent serious injury or death:

• Securely attach equipment to vehicle with

correct pin and safety chains.

• Use a tow vehicle to move equipment.

TRANSPORT HAZARD

WARNING

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

14 P1512157 R0

Table 1 Safety Decals (continued)

Part Number Description

P1513001

To prevent serious injury or death:

• Read and understand the manual before

assembling, operating, or maintaining the

equipment.

• Only trained personnel may assemble, operate,

or maintain the equipment.

• Children and untrained personnel must be kept

outside of the work area.

• Do not modify the equipment. Keep in good

working order.

• If the manual, guards, or decals are missing or

damaged, contact factory or dealer for

replacements.

• Lock out power before performing maintenance.

• To prevent equipment collapse, support equipment

tube while disassembling certain components.

• Electric motors must be grounded. Disconnect

power before resetting overloads.

WARNING

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 15

Table 1 Safety Decals (continued)

Part Number Description

P1513045

To prevent death or serious injury:

• DO NOT step on or touch moving conveyor belt.

• Shut off and lock out power to adjust, service, or

clean.

OPEN BELT CONVEYOR

WARNING

P1513002

To prevent serious injury or death:

• Keep body, hair, and clothing away from rotating

pulleys, belts, chains, and sprockets.

• Do not operate with any guard removed or

modified. Keep guards in good working order.

• Shut off and remove key or lock out power

source before inspecting or servicing machine.

ENTANGLEMENT HAZARD

WARNING

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 1. SAFETY

16 P1512157 R0

Table 1 Safety Decals (continued)

Part Number Description

P1513008

To prevent serious injury or

death, shut off power and

reattach guard before operating

machine.

MISSING GUARD HAZARD

WARNING

P1513009

To prevent serious injury or death:

• Only qualified personnel should service

electrical components.

• Disconnect and lockout power before

inspecting or servicing unit.

• Keep electrical components in good repair.

ELECTROCUTION HAZARD

WARNING

P1513035

Hydraulic fluid can cause serious injury if it

penetrates the skin. If it does, see a doctor

immediately.

• Relieve system pressure before repairing, adjusting or

disconnecting.

• Wear proper hand and eye protection when searching

for leaks. Use wood or cardboard instead of hands.

Hydraulic fluid can cause serious injury if it

penetrates the skin. If it does, see a doctor

immediately.

• Relieve system pressure before repairing, adjusting or

disconnecting.

• Wear proper hand and eye protection when searching

for leaks. Use wood or cardboard instead of hands.

HIGH PRESSURE FLUID HAZARD

WARNING

1. SAFETY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 17

2. Features

This section covers the main features of the conveyor.

Figure 5. Typical Transfer Components

Table 2. Typical Transfer Components

Item Description

1Tube

2 Hopper

3Spout Assembly

4Hood

5Hitch

4

1

3

2

5

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 2. FEATURES

18 P1512157 R0

3. Assembly

Before continuing, ensure you have completely read and understood this manual’s

Safety section, in addition to the safety information in the section(s) below.

3.1. Assembly Safety

• Do not take chances with safety. The components can be large, heavy, and hard to handle.

Always use the proper tools, rated lifting equipment, and lifting points for the job.

• Carry out assembly in a large open area with a level surface.

• Always have two or more people assembling the conveyor.

• Make sure you have sufficient lighting for the work area.

• Tighten all fasteners according to their specifications. Do not replace or substitute bolts,

nuts, or other hardware that is of lesser quality than the hardware supplied by the

manufacturer.

3.2. Check Shipment

Unload the conveyor parts at the assembly site and compare the packing slip to the shipment. Ensure that all

items have arrived and that none are damaged.

Report missing or damaged parts immediately to ensure that proper credit is received from Batco or your

distributor/dealer, and to ensure that any missing parts can be shipped quickly to avoid holding up the assembly

process.

Important

Do not assemble or install damaged components.

3.3. Required Tools

• 2 sawhorse(s) • 1 tape measure(s)

• 1 jack or forklift or overhead crane

(850 lb [386 kg] lifting capacity)

• 1 level

(2' [61 cm])

• 1 standard socket set(s) • 1 level magnetic

(2' [61 cm])

• 1 wrench set(s) • 1 ratchet strap

• 1 torque wrench(es) • 2 C-clamp(s) or vise grip(s)

• 1 power drill(s) • 1 tire pressure gauge

• 1 self-tapping screw bit

(3/8")

• 1 fish tape

(120' [36.6 m])

• 1 tire chuck

3. ASSEMBLY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

P1512157 R0 19

3.4. Before You Begin

Before you assemble the conveyor:

• Familiarize yourself with all the sub-assemblies, components, and hardware that make up the equipment.

• Have all parts and components on hand, and arrange them for easy access.

• Separate the hardware (bolts, nuts, etc.) and lay them out into groups for easier identification during

assembly.

• Ensure there is adequate space to remove the assembled conveyor from the assembly area.

3.5. Hydraulic Fittings and Bolt Tightening

Remember the following basic considerations when tightening hydraulic fittings and bolts:

• Tighten all fasteners to the torque specified in Section 5.1. – Bolt Torque on page 67. Do not replace or

substitute bolts, nuts, or other hardware that is of lesser quality than the hardware supplied by the

manufacturer.

All hydraulic fittings should be torqued to the recommended specifications. See Section 5.2. – Fittings

Torque Values on page 68.

Do not over-tighten fittings! Over-tightening hose fittings can crack the fittings or motor body

and will void the warranty.

3.6. Component Locations

Layout Drawing

Be sure to select the proper layout drawing. The dimensions change for each machine depending on the drive

option selected. Incorrect placement of the components affects machine balance and can cause a heavy or light

intake. The layout drawing is attached to the packing list.

Mark the Tube

Always ensure that the hopper remains level during the attachment of all components that bolt to the conveyor

tubing. Use a tape measure to mark out component locations that bolt to the tube. Mark locations on the top

side of the tube. Refer to the tube drawing attached to the packing list for layout measurements and

component locations.

Tightening Brackets

For all bolt-on brackets and u-clamps, tighten nuts part-way on one side of bracket, then tighten part-way on

opposite side. Do this until bracket is fully tightened and ensure it remains level during this procedure.

TRANSFER – PORTABLE GRAIN BELT CONVEYOR 3. ASSEMBLY

20 P1512157 R0

3.7. Connect the Conveyor Tube to the Hopper

1. Align the conveyor tube and hopper.

2. Fasten the tube flanges together with 7/16" x 1" bolts (2) and 7/16" locknuts (1) (see Figure 6). Ensure the

bolts are straight.

Note

A punch can be used to assist alignment. If you are not careful, it is possible to bolt the flanges

together non-concentrically with the bolts crooked through the holes.

Table 3. Tube Connection Components

Item Description

17/16" Locknut

27/16" x 1" Bolt GR8

Figure 6. Typical Tube Connection

3. Place the assembled conveyor tube and hopper on two support stands (see Figure 7).

1

2

3. ASSEMBLY TRANSFER – PORTABLE GRAIN BELT CONVEYOR

Page is loading ...

AGI HCX2 Transfer Assembly Manual

This manual is also suitable for

AGI HCX2 Transfer Assembly Manual

Related papers

Other documents