Page is loading ...
Medical Floor Stand
with VESA Tablet Security Holder
PAD-MFSV
INSTRUCTION - MANUAL
CONTENTS:
INSTALLATION:
888-733-4448
2. Attaching Enclosure to VESA
2A. Place hex nut (E) on the front side of the holder VESA in the hex hole. Then,
align holder holes (L) to VESA plate holes (A). Rotate in screws(G) from behind
until securely tightened.
A
B
C
D
E
F
G
H
I
J
M5 x 14
M5 x 8
M5 Allen Key
x4
x4
x4
Stack of 4 Piece
Foam Adapters
1A. Align base (A) to body as shown. From below, rotate in (A) screw using
provided tool (I) until securely tightened.
1. Setting up Base to Body
**Lift or push down
lever to lock or
unlock wheels
A
DM5 x 14
H
M5 Allen Key
I
M4 Allen key
M4 Nut
M4 x 10
K
L
M
x4
M4 x 10
G
A
L
3. Setting up Tray
3A. Using the small mount component (J), insert from the base (as shown
above). Using your fingers, slide until preferred height.
x2
3B. Align tray (C) to mount component (J),then
rotate in screw (F) in from front as shown using
provided allen key (I) until securely tightened.
JJA
M5 x 8
F
C
M5 Allen Key
I
I
J
E
M4 Nut
x1
N
888-733-4448
6. Setting up Cable Management / Cable Routing
6C. Fish the cable
through the entire body
& out the bottom. Route
through the opening in
the base &plug to
power surge as shown.
7. Setting up Holder & Device
**Power surge for
illustration and
NOT INCLUDED.
Adjusting Height
Rotate knob counterclock-
wise to loosen, and slide
up or down body neck to
desired height. Rotate
knob opposite direction to
securely tighten.
Adjusting Angles and Orientation
Tilt up/down for preferred angles as needed. Rotate left and
right for preferred orientation.
**Tablet shown for
illustration and
NOT INCLUDED.
6A. Insert rubber component (N) into the
side of the holder facing your device’s
charging port. Place cable as shown.
6B. Fish the wire in the back towards the cable clips to help hold the cable in place
and carefully route it from clip to clip until out the side or bottom as preferred.
(Shown above in both images)
7B. Insert key to unlock holder,
then make sure the lever is in
the ‘unlocked’ mode position.
Only then can you adjust holder
arms.
7C. Extend arms outward. Insert device in the center. Retract arms around
the perimeter of device until securely tightened. Place the lever in lock
mode, and click down on the press lock button to lock holder in place.
7A. Stick on the appropriate
foam back so that your tablet
can fit into the holder securely.
You can also stack different
foam pieces for a better fit as
needed.
View from Side of Stacking Foams
Foam
Backing
4. Setting up Basket
4A. Identify the metal plate around the center of the body. Align holes to
the basket holes (B) as shown and rotate in screws (F) using provided
tool (I) until securely tightened.
5. Setting up Power Surge (Not Included)
in the Allocated Brackets
5A. Using provided tool (I), loosen brackets a bit but not too loose that they fall. Slide in
power surge as shown. Push the bracket in towards the body, until tightly fitted against
power surge. Next, tighten screws from side with tool (I) until securely tightened.
**Power surge for
illustration and
NOT INCLUDED.
x2
M5 x 8
F
M5 Allen Key
IB
M5 Allen Key
I
M
L
N
/