ADLINK Technology NuPRO-E43 Owner's manual
- Type
- Owner's manual
Advance Technologies; Automate the World.
Manual Rev.: 2.1
Revision Date: November 2, 2023
Part No: 50M-41809-2010
NuPRO-E43
PICMG® 1.3 Full Size LGA1151 Intel® Core™
i7/i5/i3 Processor-Based SHB
User’s Manual
ii
Revision History
Revision Release Date Description of Change(s)
2.0 May 13, 2016 Initial release
2.1 November 2, 2023 Updated specs
Preface iii
NuPRO-E43
Preface
Copyright 2023 ADLINK Technology, Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.
iv Preface
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.
Table of Contents v
NuPRO-E43
Table of Contents
Preface .................................................................................... iii
List of Figures ....................................................................... vii
List of Tables.......................................................................... ix
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 1
1.3 Specifications....................................................................... 2
1.4 Block Diagram ..................................................................... 5
1.5 Functional Description ......................................................... 5
1.6 Schematics and Dimensions ............................................... 8
1.7 I/O Connectivity ................................................................... 8
1.8 Rear Panel I/O Ports............................................................ 9
1.9 Board Layout ..................................................................... 11
1.10 Onboard Connectors ......................................................... 13
1.11 Jumpers & Switches .......................................................... 20
2 Getting Started ................................................................. 21
2.1 Package Contents ............................................................. 21
2.2 Installing the CPU .............................................................. 21
2.3 Installing the CPU Fan and Heatsink................................. 25
2.4 Installing Memory Modules ................................................ 25
2.5 Driver Installation ............................................................... 28
A Appendix: BIOS Setup...................................................... 29
A.1 Entering the BIOS.............................................................. 29
A.2 Main Menu ......................................................................... 29
A.3 Advanced Menu................................................................. 30
A.3.1 CPU Configuration.................................................... 31
vi Table of Contents
A.3.2 Memory Configuration .............................................. 34
A.3.3 System Agent (SA) Configuration............................. 35
A.3.4 Graphics Configuration............................................. 36
A.3.5 PCI Express Configuration ....................................... 37
A.3.6 USB Configuration .................................................... 40
A.3.7 SATA Configuration.................................................. 44
A.3.8 Onboard Device Configuration ................................. 46
A.3.9 Advanced Power Management................................. 55
A.3.10 TPM 1.2 Configuration.............................................. 57
A.3.11 AMT Configuration.................................................... 58
A.3.12 Intel® Bios Guard Technology.................................. 59
A.3.13 Network Stack Configuration .................................... 60
A.3.14 CSM Configuration ................................................... 61
A.3.15 System Management................................................ 63
A.3.16 Miscellaneous Configuration..................................... 68
A.4 Security.............................................................................. 69
A.5 Boot ................................................................................... 70
A.6 Save & Exit ........................................................................ 72
B Appendix: Watchdog Timer ..............................................75
C Appendix: System Resources ..........................................77
C.1 System Memory Map ......................................................... 77
C.2 I/O Map .............................................................................. 77
C.3 Interrupt Request (IRQ) Lines............................................ 79
C.3.1 IRQ Lines PIC Mode................................................. 79
C.3.2 IRQ Lines APIC Mode .............................................. 79
C.3.3 PCI Configuration Space Map .................................. 82
C.3.4 PCI Interrupt Routing Map ........................................ 83
Important Safety Instructions............................................... 85
Getting Service ...................................................................... 87
List of Figures vii
NuPRO-E43
List of Figures
Figure 1-1: NuPRO-E43 Block Diagram ............................................ 5
Figure 1-2: Board Dimensions ........................................................... 8
Figure 1-3: Rear Panel I/O Ports........................................................ 9
Figure 1-4: Board Layout ................................................................. 11
viii List of Figures
This page intentionally left blank.
xList of Tables
This page intentionally left blank.
Introduction 1
NuPRO-E43
1 Introduction
1.1 Overview
The ADLINK NuPRO-E43 is a PICMG 1.3 System Host Board
(SHB) supporting the 6th Generation Intel® Core™ i7/i5/i3 and
Pentium® processors in LGA1151 package to deliver a scalable
high performance platform for a wide array of industrial
applications. The NuPRO-E43 supports 14nm process CPUs at up
to 3.7 GHz with integrated graphics and memory controllers,
Direct Media Interface (DMI) and Flexible Display Interface (FDI)
connectivity to the Intel® Q170 Express chipset. Dual-channel
DDR4 memory is supported up to a maximum of 32GB on two
DIMM slots.
These advanced features, coupled with PCI Express® x16 expan-
sion capability, dual PCI Express®-based Gigabit Ethernet, SATA
6 Gb/s and USB 3.0 support make the NuPRO-E43 ideal for vision
and automation control applications.
1.2 Features
Supports Intel® Core™ i7/i5/i3 and Pentium® processors in
LGA1151 package
Integrated Intel® HD Graphics
PCI Express® x16 expansion capability via backplane
Dual Gigabit Ethernet
8x USB 3.0 ports (2 on rear panel, 6 on SHB)
4x USB 2.0 ports on backplane
4x SATA 6 Gb/s ports on SHB
4x COM ports (including 2x RS232/422/485)
Watchdog timer, hardware monitor
Optional HD audio kit (DB-Audio2 daughter board)
Expanded TPM hardware security module
RoHS compliant
2Introduction
1.3 Specifications
Processor& System
NOTE:
NOTE:
To purchase the optional DB-Audio2 daughter board, please
contact your ADLINK sales representative.
CPU
Intel® Core™ i7-6700, 3.4GHz, 8M cache, 14nm, 65W TDP,
LGA1151 (4C/8T)
Intel® Core™ i7-6700TE, 2.4GHz 8M cache, 14nm, 35W TDP,
LGA1151 (4C/8T)
Intel® Core™ i5-6500, 3.6GHz, 6M cache, 14nm, 65W TDP,
LGA1151 (4C/4T)
Intel® Core™ i5-6500TE, 3.3GHz, 6M cache, 14nm, 35W TDP,
LGA1151 (4C/4T)
Intel® Core™ i3-6100, 3.7GHz, 3M cache, 14nm, 65W TDP,
LGA1151 (2C/4T)
Intel® Core™ i3-6100TE, 2.7GHz, 4M cache, 14nm, 35W TDP,
LGA1151 (2C/4T)
Intel® Pentium® G4400, 3.3GHz, 3M cache, 14nm, 65W TDP,
LGA1151 (2C/2T)
Intel® Pentium® G4400TE, 2.9GHz, 3M cache, 14nm, 35W
TDP, LGA1151 (2C/2T)
Intel® Celeron® G3900, 2.8GHz, 2M cache, 14nm, 65W TDP,
LGA1151 (2C/2T)
Intel® Celeron® G3900TE, 2.6GHz, 2M cache, 14nm, 35W
TDP, LGA1151 (2C/2T)
Chipset Intel® Q170 Express
Memory Dual channel DDR4-2133 up to 32 GB
BIOS AMI® UEFI BIOS
128 Mbit SPI flash memory
TPM 1x box header for TPM module
Infineon SLB 9665XT2.0
WDT 1-255 sec. or 1-255 min. software programmable, can
generate system reset
Hardware
Monitor
CPU temperature, system temperature, system voltage, CPU
fan speed
Introduction 3
NuPRO-E43
I/O
Audio
Display
OS
Microsoft® Windows® 7 32/64-bit
Microsoft® Windows® 10 64-bit
Ubuntu 15.10
Serial ATA 4x SATA 3.0 onboard with RAID support
Serial Ports
2x RS-232 via onboard 2.0 pitch box header
2x RS-232/422/485 with auto flow control via onboard
2.0 pitch box header
PCIe/PCI bus
(Via backplane)
1x PCIe x16 with Intel PCIe slot bifurcation support, can
be configured to 1x PCIex 16 or 2x PCIe x8 or 1x PCIe
x8 + 2x PCIe x4 to backplane (based on backplane), 1x
PCIe x4 to backplane, and 4x PCI to backplane
USB 8x USB 3.0 (2 on rear I/O& 6 onboard box header)
4x USB 2.0 to backplane
LPT Port 1x LPT port via onboard box header
Audio 1x box header for audio module DB-Audio2
KB/MS 1x pin header for PS/2 keyboard& mouse
Codec Realtek® ALC262 support by DB-Audio2
daughter board
Interface Intel® High Definition Audio via onboard box
header
Graphics Integrated Intel® HD series, based on CPU
for different GPU
VGA 1x VGA on rear I/O, resolution up to 1920 x
1200@60Hz
DVI-D 1x DVI-D via onboard pin header, resolution
up to 1920 x 1200@60Hz
4Introduction
Ethernet
Manageability
Mechanical and Environmental
Controller LAN1: Intel® I219LM PHY via RJ45
LAN2: Intel® I225-V via RJ45
Interface PCIe x1 bus
iAMT Support iAMT 11
Wake On LAN Support on LAN1
SEMA SEMA support with BMC
SEMA Cloud
Form Factor Full-sized PICMG® 1.3 system host board
Dimensions 338 mm x 126 mm (L x W)
Operating Temperature 0 to 60°C
Storage Temperature -40 to 80°C
Certification CE & FCC Class A
Relative Humidity 5% to 95%, non-condensing
Introduction 5
NuPRO-E43
1.4 Block Diagram
Figure 1-1: NuPRO-E43 Block Diagram
1.5 Functional Description
Processor Support
The NuPRO-E43 is PICMG 1.3 System Host Board supporting the
6th Generation Intel® Core™ processor family (Intel® Core™ i7/
i5/i3) in LGA1151 socket. An integrated memory controller sup-
ports dual channel DDR4 and Intel® HD Graphics is integrated
onboard the CPU. The CPU provides a PCI Express x16 for exter-
nal graphics or expansion. Direct Media Interface (DMI) and Flexi-
ble Display Interface (FDI) provide connectivity to the Intel® Q170
Express Chipset.
Intel® Q170 Express Chipset
The Intel® Q170 Platform Controller Hub (PCH), with the proces-
sor, provides a compact yet powerful 2-chip solution, with Direct
Media Interface (DMI) chip-to-chip connection between the pro-
6Introduction
cessor and PCH and Intel Flexible Display Interface transmitting
display traffic from processor-based integrated graphics to the leg-
acy display connectors in the PCH, including PCI Express, SATA
6 Gb/s, USB 3.0, LPC and SPI.
Dual-Channel DDR4 Memory
To meet the requirements of memory-intensive applications,
NuPRO-E43 dual-channel memory architecture supports DDR4
2133 MHz DIMMs, which delivers higher bandwidth and increased
performance with lower power consumption than DDR3.
Gigabit Ethernet
The NuPRO-E43 utilizes an Intel® I219LM Gigabit Ethernet PHY
and Intel® I211-AT Gigabit Controller connected to the PCI-E bus
of the Q170 PCH, with Intel® AMT 11 (I219LM on LAN1), Wake-
on-LAN, and PXE supported.
Serial ATA
The NuPRO-E43 provides four Serial ATA ports with data transfer
rates of up to 6.0 GB/s. Intel® Rapid Storage Technology supports
AHCI and RAID 0/1/5/10 functionality.
Universal Serial Bus (USB 2.0/3.0)
The NuPRO-E43 provides 4 USB 2.0 ports (backplane) supporting
transfer rates up to 480 Mb/s and 8 USB 3.0 ports (2x on rear
panel, 6x on SHB) supporting transfer rates up to 5 Gb/s. All ports
are USB 2.0/1.1 compatible.
Hardware Monitoring
A built-in, proactive hardware monitoring system in the Super I/O
monitors the CPU temperature, system fan speed, and voltage
levels to prevent overheating and/or component damage, effect
timely failure detection, and ensure stable supply of current for
critical components.
Introduction 7
NuPRO-E43
Watchdog Timer
The watchdog timer (WDT) monitors system operations based on
user-defined configurations. The WDT can be programmed for dif-
ferent time-out periods, such as from 1 to 255 seconds or from 1 to
255 minutes. The WDT generates a reset signal, then a reset
request, after failure to strobe it within the programmed time
period. A register bit may be enabled to indicate if the watchdog
timer caused the reset event. The WDT register is cleared during
the power-on sequence to enable the operating system to take
appropriate action when the watchdog generates a reboot.
Trusted Platform Module
The NuPRO-E43 optionally supports TPM ver. 1.2 (Trusted Plat-
form Module) for secure storage of keys, passwords and digital
certificates. Systems supporting TPM offer improved hardware-
based security in numerous applications, such as file and folder
encryption, local password management, S-MIME e-mail, VPN
and PKI authentication and wireless authentication for 802.1x and
LEAP.
Intel® Active Management Technology
Intel® Active Management Technology (Intel® AMT) is hardware-
based technology for remotely managing and securing PCs out-of-
band. Intel® AMT includes hardware-based remote management,
security, power-management, and remote-configuration features.
Intel® AMT allows remote access to a system when traditional
techniques and methods are not available.
8Introduction
1.6 Schematics and Dimensions
Figure 1-2: Board Dimensions
1.7 I/O Connectivity
NOTE:
NOTE:
All dimensions shown are in mm (millimeters).
I/O Bracket Onboard Edge
Connector Remarks
VGA Y — — DB-15
DVI-D — Y —
Cable w/ bracket
optional
LAN1/2 (RJ-45) Y — — Act/Link/
Speed LEDs
PS/2 KB/MS — Y — Cable w/ bracket
optional
USB rear panel 2 — — USB 3.0
USB 3.0 headers — 6 — Cable w/ bracket
optional
USB backplane — — 4 USB 2.0
COMA-D — Y — 2.00” pitch
126.4
123.1
20.6
338.1
333.6
151.8
111
126.4
39.6
Introduction 9
NuPRO-E43
Table 1-1: NuPRO-E43 I/O Connectivity
1.8 Rear Panel I/O Ports
Figure 1-3: Rear Panel I/O Ports
SATA — 4 — —
PCIe x4 — — Y —
PCIe x16 — — Y —
PCI 32bit/33MHz — — Y via ITE IT8892
Connector Description
A LAN1 (RJ-45) Gigabit Ethernet (supports Intel® AMT)
B LAN2 (RJ-45) Gigabit Ethernet
I/O Bracket Onboard Edge
Connector Remarks
A
B
C
D
10 Introduction
Table 1-2: Rear Panel I/O Legend
USB 3.0 Connectors
LAN (RJ-45) Ports
C VGA DB-15 connector for CRT or LCD monitor
D USB 3.0 x2 SuperSpeed USB 3.0 ports
Pin # Signal Name
1 USB3.0_P5VA
2 USB2_CMAN
3 USB2_CMAP
4GND
5 USB3A_CMRXN
6 USB3A_CMRXP
7GND
8 USB3A_CMTXN
9 USB3A_CMTXP
Pin # 10BASE-T/
100BASE-TX 1000BASE-T
1 TX+ BI_DA+
2 TX- BI_DA-
3 RX+ BI_DB+
4 -- BI_DC+
5 -- BI_DC-
6 RX- BI_DB-
7 -- BI_DD+
8 -- BI_DD-
LED1 LED2
Status Description Status Description
Off No Link Off 10 Mb connection
Connector Description
LED2
LED1
18
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
ADLINK Technology NuPRO-E43 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ADLINK Technology NuPRO-E72 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Nu Technology 6U Compact PCI Highly Integrated Single Slot Dual Bridge Low Power Pentium-III CPU Module User manual
-
Adlink CEI-4x10GBASE-T Network Adapter Card Owner's manual
-
Diebold Nixdorf BEETLE /M-III - Mx Operating instructions
-
-
Wincor Nixdorf Motherboard M1 and M2 POS Operating instructions
-
-
-
Nexcom PEAK 888VL2 User manual
-
AXIOMTEK eBOX671-517-FL User manual
-
DFI WM343-SD User manual
