BLACK+DECKER GT259 User manual

®

GT249 GT259

GT250 GT260

GT251 GT261

Page is loading ...

2

Hedgetrimmer

GT249/250/251/259/260/261

Introduction

This manual provides operating and maintenance

instructions for all of the hedgetrimmers in the

Black & Decker GT250/260 range including the

GT249/259.

Description (Fig. A)

A

1. Front handle switch

2. Front handle

3. Rear switch

4. Handle guard (GT251C & GT261C)

5. Front guard (GT249C, GT250C,

GT259C & GT260C)

6. Blade

7. Blade sheath

Know your machine

!

Warning! When using electric tools, basic

safety precautions should always be taken to

reduce the risk of fire, electric shock and

personal injury.

Read this manual carefully, observing

all of the recommended safety instructions

before, during and after using your

machine. Maintain your machine in good

working order.

Familiarise yourself with the controls on your

machine before attempting to operate it,

but above all, be sure you know how to stop

the machine in an emergency.

Retain this manual and all other literature

supplied for future reference.

Safety instructions

Preparation

• Dress properly. Do not wear loose

clothing or jewellery which could get

caught in moving parts. Always wear

stout, non-skid footwear and gloves

when operating your machine and

make sure that long hair is kept away

from the blades.

• Protect your eyes/ears. Use safety

glasses or goggles while operating your

Instruction Manual

machine. If the sound level seems

uncomfortable, use ear protection.

• Use outdoor extension cords. Never

use an indoor extension cable for use

with this machine.

• Do not abuse the cord. Never carry the

hedgetrimmer by its cord or yank the

cord to disconnect it from the socket.

Keep the cord away from heat, oil and

sharp edges.

• Remove the plug from the mains

immediately if the cable is damaged

or cut.

• Inspect hedge. Ensure that the hedge

has nothing lying on top of it or beside it,

e.g. barbed wire or railings which may

damage your machine.

• Consider the work environment.

Do not use the machine in the rain or

allow it to get wet or damp. Keep the

work area well lit. Do not use in the

presence of flammable liquids or gases.

Operation

• Avoid unintentional starting. Do not

carry a plugged-in tool with a finger on

the switch.

• Before using the machine. Disconnect

it from the electrical supply and visually

check that the blade fixings are secure.

A damaged blade or loose blade nuts are

a major hazard and must be replaced.

Always be sure that your machine is in a

safe operating condition.

• Guard against electric shock.

Avoid touching grounded surfaces

(e.g. railings, lamp posts etc.) while using

your machine.

360˚

6m/20ft

• Keep people away while the machine

is in use. Do not allow children, other

people or animals near your machine

while you are using it - always keep them

at least 6m (20ft) away from the cutting

area and never let anyone touch the

machine or the extension cord.

• Do not force the tool. It will do the job

better and more safely at the rate for

which it was intended.

3

ENGLISH

• Use the right tool. Never force small

tools or attachments to do the job of a

heavy duty tool. Do not use tools for

purposes not intended: e.g, do not use

the hedgetrimmer as a chain saw.

• Do not overreach. Keep proper footing

and balance at all times, especially while

working on a slope.

• Stay alert. Watch what you are doing.

Use common sense. Do not operate

when you are tired.

!

• Use the correct electrical supply.

Your machine is designed for use on

AC (mains) electrical supplies only - do

not attempt to use on any other supply.

Be sure to plug the machine into a power

point, never a lighting socket.

• Always turn off and unplug the

machine. Whenever you leave the

machine unattended. Before checking,

cleaning, adjusting, unjamming

the blades or carrying out work on

the machine. If the machine starts to

vibrate abnormally, check immediately.

After striking a foreign object- inspect for

damage and make repairs as necessary.

• Always keep the power supply cable

away from the blades. Be aware of its

position at all times.

• Do not put your hands or feet near the

blades and never attempt to stop the

blades - they will stop on their own.

• Never operate your machine with a

broken or missing guard.

• Remember that the operator/user is

responsible for accidents or hazards

occurring to other people or their

property. A first time user should get

some practical instruction on how to

use a hedgetrimmer as well as reading

this manual.

Maintenance and storage

• Always disconnect the machine

before carrying out any adjustment,

servicing or maintenance.

• Always lubricate the blades with

light machine oil after use to prevent

corrosion damage.

• Maintain tools with care. Always keep

tools sharp and clean for better and safer

performance. Follow instructions for

lubricating and changing accessories.

Inspect tool cords periodically and if

damaged have repaired by an authorised

service facility. Inspect extension cords

periodically and replace if damaged.

Keep handles dry, clean and free from oil

and grease.

• Check damaged parts. Before further use

of the tool, a guard or other part that is

damaged should be carefully checked to

determine whether it will operate properly

and perform its intended function. Check

for alignment of moving parts, binding of

moving parts, breakage of parts, mounting

and any other conditions that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced by an authorised service centre

unless otherwise indicated in this

instruction manual. Have defective

switches replaced by an authorised service

centre. Do not use the tool if the switch

does not turn it on and off.

!

Warning! The use of any accessory or

attachment, other than recommended in this

instruction manual, may present a risk of

personal injury.

Double insulation

Your machine is double insulated. This

means that all external metal parts are

electrically isolated from the power supply.

This is achieved by placing an extra

insulation barrier between the electrical and

mechanical parts. Double insulation means

greater electrical safety and obviates the

necessity of having the machine earthed.

Electrical safety

Your machine should always be switched off

at the mains before disconnecting any plug

and socket connector or extension cables.

Fuse replacement

If your machine is supplied with cable fitted

with a non-re-wireable plug.

• The plug is fitted with a 3 amp fuse

which is the recommended fuse for

your machine.

• Only use replacement fuses which are

approved to BS1362.

• When changing the fuse in your plug,

always ensure the fuse cover is refitted.

If the fuse cover is missing or damaged

do not use the plug.

Note: Fuses do not give personal protection

against electric shock.

4

Plug replacement

• Disconnect the plug from the supply.

• Cut off the plug and dispose of

immediately. Insertion of a detatched

plug into a 13 amp socket outlet may

result in electric shock.

• Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit a 3 amp

fuse approved

to BS1362

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug

(see above). Brown is for “Live” (L) and

blue is for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

!

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable

directly into your machine yourself.

Instead, take your machine to your

nearest Black & Decker service centre.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA 30mS) circuit breaker in the house

wiring. If you do not wish to have one

installed, then we strongly recommend that

the electrical power to the machine be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

!

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

the machine from the safety instructions and

safe working practices given in this manual.

We recommend that if your mains cable

is cut or requires replacement that you

return your machine to a Black & Decker

service centre. When repaired, your

machine will be tested for electrical safety.

Cable connection system

Black & Decker continually make every effort to

achieve the highest standards in performance, quality

and reliability and recommend the use of a new

outdoor cable connection system.

The new system gives additional protection against

the possibility of water or moisture entering into the

cable connector during normal use.

Note: The new connection system does not release

the operator of the machine from the safety

precautions and safe working practices given in the

instruction leaflet. Particular attention is drawn to the

coupler system as being ‘weather resistant’ and not

suitable for immersion, submersion or being

subjected to water jets. Care should be taken to

prevent the cable from lying or trailing through pools

of water or from splashing with hose pipes.

A6615 20m cable, socket, 13 amp plug

A6616 20m cable, socket, 13 amp plug and

cable tidy frame

A6617 30m cable, socket, 13 amp plug and

cable tidy frame

A6613 40m cable, socket, 13 amp plug and

cable tidy reel

Existing cable systems

Your hedge trimmer comes with either, 12 metre

cable attached (Cat. number ends with a C), or a

male connector built into the product. If you already

own an outdoor cable system, we recommend that

you replace the existing ‘female’ cable connector with

the new ‘female’ connector which is available

as an accessory from most major DIY retail outlets

and from Black & Decker service centres

(cat. no. A6624S).

old ‘female’ connector new ‘female’ connector

When fitting the connector, follow the instructions

which are supplied with it. If in doubt, consult a

qualified electrician.

Existing powered garden tools

To connect existing Black & Decker garden power

tools to the new system you will require an adaptor

(see below). This is available as an accessory from

most major DIY retail outlets (cat. no. A6623S).

5

ENGLISH

!

Warning! This adaptor is only suitable for

products rated up to 500W. It is not

recommended for use with the following:

Hover mowers, rotary mowers with grass

collection, chainsaws, shredders and blower

vacs. Please contact your local service

centre should you require further advice.

Fitting your own extension cable

• When making your own extension cable, fit a

13 amp plug (see “fitting the mains plug”) to one

end of the cable and a ‘female’ connector to the

other end (see below). For wiring instructions see

those supplied with the female connector.

• A ‘male’ connector is already attached to the

electrical supply cable on your machine and is

designed to be non-rewireable (see below).

This should not be removed. Should the plug

become damaged or need replacing, please

return the machine to your Black & Decker

service centre.

‘female’ connector ‘male’ connector

!

Warning! Never wire an extension cable with

anything other than the ‘female’ connector

supplied and a 13 amp BS1363A approved

plug with the recommended fuse. Never

wire a ‘male’ connector to your extension

cable and never wire an extension cable

with a plug of any kind at each end of the

cable. This is extremely dangerous and

results in the pins being live which may

cause a fatal electric shock.

Technical data

Specifications

Insulation Class II

Strokes per minute 1900

Blade length 41cm, 51cm

Weight 2.4 to 2.5kg

Noise 88dB (A)

Vibration <2.5m/s

2

Assembly (Figs. B & C)

B

• You will need a number 2 Posidrive

screwdriver.

• During assembly it is recommended that

the blade sheath is fitted over the blades

to reduce the risk of injury.

Fitting the guard

C

• Slide the guard into position as shown.

• Fix in place using two of the screws

provided. Do not over tighten them.

Operation (Fig. D)

To start the hedgetrimmer

• Press the front handle switch (Fig. A.1).

• Squeeze the rear switch (Fig. A.3).

• The hedgetrimmer will now run.

To stop the hedgetrimmer

• Release the front handle switch or the

rear switch.

D

This product is built with a cable retention

system. To operate this, feed your cable

through the hole provided and hook it over

the pegs as shown in Fig. D.

Useful hints for trimming hedges

(Fig. E)

Read the safety rules first!

Cutting

E

• Tip the blades a little towards

the hedge (Fig. E1).

• First cut both sides, working from the

bottom up, then trim the top (Fig. E2).

• Take care to avoid any hard objects in or

around the hedge that could damage

the blades.

• Where the branches are very long,

cut the hedge back in several stages

(short cuttings are easier to tidy up).

When to trim

• As a general guide, hedges and shrubs

with seasonal leaves (new ones each year)

can be trimmed in June and October.

• Evergreens can be trimmed in April

and August.

6

• Conifers and other fast growing shrubs

can be trimmed about every six weeks

from May onwards.

Failure to work

If your hedgetrimmer does not work, unplug it

and check:

• The power point (try another tool or appliance).

• The plug and its fuse.

• The plug and socket connections.

If in doubt, get help from a qualified electrician, or visit

your Black & Decker service centre.

Care and maintenance

• Switch off and disconnect from power supply

before cleaning or adjusting your machine.

• For best performance, keep the blades and air

slots in the motor housing clean. Use a cloth or

brush to remove cuttings, sap or other debris.

• Prevent the blades from rusting by applying a film

of light machine oil after cleaning.

• Plastic parts may be cleaned by using a non

abrasive cleaner and a cloth dampened with

warm water.

• Do not immerse any part of the hedgetrimmer

in water.

• Avoid all other types of detergents, cleaners or

solvents. These may contain chemicals that

could seriously damage the plastic. Do not spray

the hedgetrimmer with water, and do not allow

water to enter the hedgetrimmer.

• After cleaning, the tool can be stored in its

packaging for protection.

• Self lubricating bearings are used in the tool and

lubrication is not required. (Other than to the

blades as stated above).

What to do if your hedgetrimmer

needs repair

Information on how and where to send your

hedgetrimmer for repair or service is given at the

back of this leaflet. We recommend you keep this

in a safe place.

Unwanted products and

the environment

Should you find one day that your product

needs replacement, or is of no further

use to you, think of the protection of the

environment. Black & Decker service centres

will accept your old products and will dispose

of them in an environmentally safe way.

Black & Decker lawn and

garden guarantee

This guarantee provides 36 months parts cover

and 12 months labour. In all cases proof of

purchase will be required.

If your Black & Decker product becomes defective,

within the guarantee period, due to faulty materials

and workmanship, we guarantee to either replace all

defective parts, or at our discretion, replace the unit

free of charge, provided that:

• The product is returned to us or our authorised

repairers with evidence of purchase.

• The product has been used within the

parameters of its consumer classification.

• The product has not been used for hire

purposes.

• Repairs have not been attempted by anyone

other than our own service staff or authorised

repairers.

• The failure represents normal wear and tear.

This guarantee is offered as an extra benefit and is

additional to your statutory rights.

The guarantee policy

Failures due to the following are not covered:

• Replacing worn or damaged blades, nylon line

and chains, or cords damaged during storage or

use. These are regarded as replacement items

which wear during normal usage.

• Failures as a result of sudden impact or

obvious abuse.

• Failures due to usage not in accordance with

instructions and recommendations contained in

the instruction manual.

The use of other than genuine Black & Decker

accessories and parts may damage or reduce the

performance of you Black & Decker product and

may render the guarantee void.

Black & Decker after sales service

Black & Decker offers a nationwide after sales service

through company operated service centres. It is our

aim to offer excellent service, fast repairs, extensive

parts availability and full accessory support.

If you need any help or advice please contact your

local Black & Decker service centre manager.

Full details of our unique after sales service can be

obtained from any of our service centres (a full

directory is printed on the reverse of the parts

drawing included with your product).

7

ENGLISH

Other Black & Decker products

Black & Decker has a full range of outdoor power

tools that make life easy in the garden. If you would

like further information on other products, please

contact the Black & Decker service information

centre at the address on the back cover, or contact

your Black & Decker stockist.

Other products include (UK only):

Lawn mowers Hedge trimmers

Grass trimmers Chainsaws

Lawnrakers Compost shredders

Blower vacs

EC Declaration of Conformity

We declare that units:

GT249, GT250, GT251, GT259, GT260, GT261

conform to: 89/392/EEC, 89/336/EEC,

EN50144, EN55014, EN55104, 73/23/EEC

A weighted sound pressure 91dB (A)

A weighted sound power 104dB (A)

Hand/arm weighted vibration <2.5m/s

2

Brian Cooke

Director of Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

8

Tagliasiepi

GT249/250/251/259/260/261

• Non trasportate mai l’utensile tenendolo

per il cavo. Non estraete la spina tirando

il cavo. Tenete il cavo lontano da fonti di

calore, olii e superfici taglienti. Controllate

sempre le condizioni del cavo prima

dell’utilizzo e non usatelo se danneggiato.

• Utilizzate soltanto cavi di prolunga

previsti per l’uso esterno.

Abbigliamento

• Portate sempre scarpe pesanti o stivali.

• Portate sempre occhiali protettivi, guanti

e protezioni per l’udito durante l’uso.

• Raccogliete i capelli lunghi per evitare

contatti con parti mobili della macchina.

• Portate abiti aderenti ma che non

impediscano il libero movimento.

• Non portate bracciali e catenine lunghe.

Utilizzo della vostra macchina

• Per prima cosa familiarizzate con il

tagliasiepi e leggete attentamente

questo manuale.

• Controllate sempre che la protezione sia

montata.

• Evitate accensioni accidentali, non

portate l’utensile alla siepe con la spina

già collegata.

• Durante il trasporto dell’utensile utilizzate

i foderi previsti per la protezione delle lame.

• Rimuovete dalla siepe ogni cavo o

oggetto solido prima di iniziare il lavoro.

• Non usate il tagliasiepi in spazi ristretti.

• Lavorate solo durante le ore di buona

luminosità.

• Tenete l’area di lavoro libera dai pezzi

tagliati.

• Durante il taglio tenete il tagliasiepi

davanti a voi. Usate entrambe le mani e

tenete il cavo dietro di voi.

• Non forzate l’utensile. Mantenendo una

velocità di taglio costante otterrete i

risultati migliori.

• Non sporgetevi. Mantenete sempre un

appoggio saldo ed un buon equilibrio.

• Lavorate con attenzione. Non utilizzate

l’utensile se vi sentite stanchi.

Introduzione

Questo manuale fornisce le istruzioni per il

funzionamento e la manutenzione dei tagliasiepi

GT249/250/251/259/260/261.

Descrizione (Fig. A)

A

1. Interruttore impugnatura anteriore

2. Impugnatura anteriore

3. Interruttore posteriore

4. Pulsante blocca-interruttore (GT251C e

GT261C)

5. Protezione trasparente (GT249C,

GT250C, GT259C e GT260C)

6. Lama

7. Fodero lama

Norme di sicurezza

Leggete attentamente tutte le istruzioni

contenute in questo manuale per sapere

cosa fare prima, durante e dopo l’utilizzo

della macchina. Rispettate le norme di

sicurezza e seguite le avvertenze per una sua

corretta manutenzione.

Collegamento elettrico

• L’utensile è stato progettato per essere

usato unicamente con corrente alternata

- non si può utilizzare con altri tipi di

elettricità. Controllate che il voltaggio

della presa corrisponda a quello indicato

sulla targhetta dell’utensile.

• Non lasciate la macchina collegata in

vostra assenza. Spegnetela e togliete la

spina dalla presa.

!

• Spegnete sempre la macchina e

rimuovete la spina prima di procedere ad

ispezionare, pulire o regolare qualsiasi

componente del tagliasiepi. Fate

attenzione che il cavo non sia danneggiato

o incastrato prima di riporre l’utensile.

Cavo elettrico

• Il cavo deve essere controllato regolarmente

e utilizzato solo se in buone condizioni.

• Tenete sempre il cavo lontano dalle

lamesiate certi in ogni momento della

sua posizione.

Istruzioni per l’Uso

Page is loading ...

17

Heggeschaar

GT249/250/251/259/260/261

Inleiding

Deze handleiding bevat gebruiks- en

onderhoudsinstructies voor alle heggescharen uit de

Black & Decker GT250 en GT260 serie, inclusief de

GT249 en GT259.

Beschrijving (Fig. A)

A

1. Voorste handgreepschakelaar

2. Voorste handgreep

3. Achterste schakelaar

4. Vergrendelingsknop (GT251C & GT261C)

5. Beveiliging (GT249C, GT250C, GT259C

& GT260C)

6. Blad

7. Mesbeschermer

Veiligheidsvoorschriften

Als u elektrische gereedschappen gebruikt,

moet u altijd de basisveiligheidsvoorschriften

in acht nemen om het risico van brand,

elektrische schokken en lichamelijke letsels

te vermijden. Lees de onderstaande

veiligheidsvoorschriften zorgvuldig door voor

u het gereedschap gebruikt.

Elektrische aansluiting

• Uw heggeschaar is alleen ontworpen om

op wisselstroom (netspanning) te worden

aangesloten - probeer de machine nooit

op een andere spanning aan te sluiten en

zorg er steeds voor dat ze aan uw

stroomvoorziening is aangepast.

De spanning voor deze machine is

aangegeven op het kenplaatje.

• Steek de stekker van de machine altijd in

een stopcontact en nooit in een

contactdoos voor verlichtingstoestellen.

• Laat de machine nooit onbewaakt

achter als de stekker nog in het

stopcontact steekt.

!

• Trek altijd de stekker uit het stopcontact

voor u de vastgelopen snijmessen van

de heggeschaar vrijmaakt, de machine

schoonmaakt of controleert, een

onderdeel van de heggeschaar bijstelt,

als het elektriciteitssnoer beschadigd is

of in de war zit, of als de heggeschaar

niet werkt.

Elektriciteitssnoer

• Het elektriciteitssnoer moet regelmatig

op beschadigingen of slijtage worden

gecontroleerd en mag alleen in goede

staat worden gebruikt.

• Houd steeds in het oog waar het

elektriciteitssnoer zich precies bevindt.

• Draag de machine nooit bij het snoer en

trek niet aan het snoer om de

stekkerverbindingen uiteen te halen.

Houd het snoer uit de buurt van

warmtebronnen, olie of scherpe randen.

Controleer de staat van het snoer voor u

de machine in werking stelt en gebruik

het niet als het beschadigd is.

• Gebruik alleen elektriciteitssnoeren die

geschikt zijn om buitenshuis te werken.

Kleding

• Draag steeds stevige schoenen of

laarzen.

• Draag steeds een beschermende bril,

handschoenen en oorbeschermers als u

met de machine werkt.

• Zorg ervoor dat lang haar niet in contact

kan komen met de heggeschaar.

• Draag goed aansluitende kleding, die u

echter niet hindert bij uw bewegingen.

• Draag geen loshangende juwelen.

Gebruik van de machine

• Iemand die de machine voor het eerst

gebruikt, moet degelijke praktische

informatie krijgen over hoe een

heggeschaar moet worden gebruikt en

deze handleiding zorgvuldig lezen.

• Zorg er steeds voor dat de beveiliging is

aangebracht.

• Vermijd ongewenst starten. Draag uw

heggeschaar niet tot bij de haag terwijl

de stekker in het stopcontact steekt.

• Breng de meegeleverde mesbeschermer

over de snijmessen aan als u de

heggeschaar draagt.

• Verwijder alle draden of andere harde

voorwerpen van de haag voor u deze

begint te snoeien.

Gebruiksaanwijzing

Page is loading ...

26

Kλαδευτήρι Θάµνων

GT249/250/251/259/260/261

Oδηγίες Xρήσεως

Oδηγιες øρησης

Για Black & Decker GT250, GT260 και GT249,

GT259.

Περιγραæή (EικÞνα A)

A

1. ∆ιακÞπτης εµπρÞσθιας λαâής

2. EµπρÞσθια λαâή

3. Oπίσθιïς διακÞπτης

4. Kïυµπί απασæάλισης (GT251C &

GT261C)

5. Πρïæυλακτήρας (GT249C, GT250C,

GT259C & GT260C)

6. Λεπίδα

7. Θήκη λεπίδας

Oδηγίες ασæάλειας

Oταν øρησιµïπïιείτε ηλεκτρικά εργαλεία,

να λαµâάνετε πάντïτε τα αναγκαία

µέτρα ασæαλείας για να µειώνετε τïν

κίνδυνï πυρκαγιάς, ηλεκτρικïύ σïκ και

πρïσωπικïύ τραυµατισµïύ. ∆ιαâάστε

Þλες τις ïδηγίες πρïτïύ

øρησιµïπïιήσετε τï εργαλείï.

Hλεκτρικές συνδέσεις

• H µηøανή σας είναι σøεδιασµένη

για øρήση σε ρευµατïδÞτες

εναλλασσÞµενïυ ρεύµατïς µÞνï - µη

δïκιµάσετε να øρησιµïπïιήσετε άλλï

σύστηµα ρεύµατïς και âεâαιωθείτε

Þτι η µηøανή σας είναι συνδεδεµένη

µε τïν ïρθÞ ρευµατïδÞτη. Tï âïλτάú

γι· αυτή τη µηøανή δίνεται στην

πλάκα αναλïγιών.

• Tïπïθετήστε τη µηøανή σας στï

σηµείï ηλεκτρικής παρïøής - πïτέ

µέσα σε αναµµένη πρίúα.

• Mην αæήνετε τη µηøανή σας

απαρακïλïύθητη ενώ την συνδέετε

στην ηλεκτρική παρïøή.

!

• Πάντïτε να σâήνετε και να

αæαιρείτε την πρίúα απÞ τïν αγωγÞ

ρεύµατïς Þταν êεâïυλώνετε τις

λεπίδες, πριν απÞ τï καθάρισµα, την

επίâλεψη ή τη ρύθµιση

ïπïιïυδήπïτε µέρïυς της µηøανής

κïψίµατïς, ή αν τï καλώδιï αγωγïύ

έøει πάθει âλάâη ή έøει εµπλακεί, ή

εάν τï µηøάνηµα ψαλιδίσµατïς τïυ

æράκτη δεν λειτïυργεί.

Kαλώδιï αγωγïύ ρεύµατïς

• Tï καλώδιï παρïøής ρεύµατïς

πρέπει να εêετάúεται ταøτικά για

τυøÞν σηµάδια âλάâης ή παλιώµατïς,

και να øρησιµïπïιείται µÞνïν Þταν

είναι σε καλή κατάσταση.

• Nα πρïσέøετε πάντïτε πïύ είναι η

θέση τïυ καλωδίïυ ρεύµατïς.

• Πïτέ µη µεταæέρετε τη µηøανή σας

απÞ τï καλώδιï ή να σηκώνετε τï

καλώδιï για να øωρίúετε τïυς

συνδετήρες. ∆ιατηρείτε τï καλώδιï

µακρυά απÞ πηγές æωτιάς, απÞ

λάδια ή κïæτερά αντικείµενα.

Eêετάστε την κατάσταση τïυ

καλωδίïυ σας πριν απÞ τη øρήση

και µην την øρησιµïπïιείτε άν

έπαθε âλάâη.

• Nα øρησιµïπïιείτε µÞνïν τα

καλώδια ρεύµατïς πïυ είναι για

υπαίθρια øρήση.

PïυøισµÞς

• Πάντïτε να æïρείτε σκληρά

παπïύτσια ή µπÞτες.

• Πάντïτε να æïράτε πρïστατευτικά

γυαλιά, γάντια και πρïστατευτικά

µέσα αυτιών Þταν øρησιµïπïιείτε

τï µηøάνηµα.

• Nα πρïστατεύετε τα µακρυά µαλλιά

να µην έρøïνται σ’ απαæή µε τï

µηøάνηµα ψαλιδίσµατïς.

• Tα ρïύøα σας να µην είναι æαρδιά,

αλλά Þøι τÞσï στενά πïυ να

παρεµπïδίúïυν την κίνησή σας.

• Nα µην æïράτε øαλαρά κïσµήµατα.

Xρησιµïπïιώντας τη µηøανή σας

• O øρήστης πρώτης æïράς θα πρέπει

να λαµâάνει πληρïæïριακές

πρακτικές ïδηγίες στï πώς να

øρησιµïπïιεί τï µηøάνηµα

ψαλιδίσµατïς æράκτη, και να

διαâάσει επίσης αυτÞ τï εγøειρίδιï.

Page is loading ...

42

®

Australia Black & Decker (A’asia) Pty Ltd Tel: 03 213 8200

286-288 Maroondah Highway Fax: 03 726 7150

North Croydon, Victoria 3136

Belgique/België Black & Decker Belgium NV Tel: 02 719 07 11

Weihoek 1, Nossegem Fax: 02 721 40 45

1930-Zaventem-Zuid

Danmark Black & Decker AB Tlf: 70-20 15 10

Hejrevang 26 B, 3450 Allerød Fax: 48-14 13 99

Deutschland Black & Decker GmbH Tel: 06126 210

Black & Decker Straße 40 Fax: 06126 212435

65510 Idstein

Eλλάς Black & Decker (Eλλάς) AE Tηλ: 01 9242870-75

Λεωæ. Συγγρïύ 154 Service: 01 9242876-7

Aθήνα 176 71 Fax: 01 9242869

España Black & Decker de España SA Tel: 977 297110

Ctra. de Acceso a Roda de Bará, km 0,7 Tlx: 56631 BLADE E

43883-Roda de Bará, Tarragona Fax: 977 802342

France Black & Decker (France) Sarl Tel: 72 20 39 20

Le Paisy Tlx: 300 250

69570 Dardilly, Lyon Fax: 72 20 39 00

Helvetia Black & Decker AG Elektrowerkzeuge Tel: 01 730 69 33

Rütistraße 14, CH-8952 Schlieren Tlx: 54462 BDZH CH

Schweiz/Suisse Fax: 01 730 70 67

Italia Black & Decker Italia SpA Tel: 039 23 87 1

Viale Elvezia 2, 20052 Monza (Mi) Fax: 039 23 87 59 3

Nederland Black & Decker (Nederland) BV Tel: 07650 82000

Florijnstraat 10 Fax: 07650 38184

4879 AH Etten-Leur

New Zealand Black & Decker Tel: 09 579 7600

483 Great South Road, Penrose, Auckland Fax: 09 579 8200

Norge Black & Decker (Norge) A/S Tel: 22-32 46 40

Strømsveien 344, 1081 Oslo Fax: 22-32 46 50

Österreich Black & Decker Tel: 0222 66 116-0

Werkzeugevertriebs GmbH Tlx: 13228 BLACK A

Erlaaerstraße 165, Postfach 69, 1231 Wien Fax: 0222 66 116-14

Portugal Black & Decker Tel: 468 76 13/468 75 13

Rua Egas Moniz 173, Apartado 19 Tlx: 16 607 BLADEC P

S. João do Estoril, 2768 Estoril, Codex Fax: 467 15 80

South Africa Powerdek Tool Distributors Tel: 011 493 4000

22 Inglestone Road, Village Deep Fax: 011 493 6391

Johannesburg, South Africa

Suomi Black & Decker Oy Puh: 358-9 825 4540

Rälssitie 7 C, 01510 Vantaa Fax: 358-9 825 45444

Frälsevägen 7 C Tel: 358-0 825 4540

01510 Vanda Fax: 358-0 825 45444

Sverige Black & Decker AB Tel: 031-68 60 00

Box 603, 421 26 Västra Frölunda Fax: 031-68 60 08

Besöksadr. Ekonomivägen 11

United Kingdom Black & Decker Tel: 01753 511234

210 Bath Road, Slough Tlx: 848317 BAND MH

Berkshire SL1 3YD Fax: 01753 551155

Part no. 369162-01 10/96

43

Forhandler adresse

Händleradresse

∆ιεύθυνση αντι ρïσώ ïυ

Address of dealer

Dirección del detallista

Cachet du revendeur

Indirizzo del rivenditore

Adres van de dealer

Forhandlerens adresse

Morada do revendedor

Jälleenmyyjän osoite

Återförsäljarens adress

Indkøbsdato

Kaufdatum

Hµερïµηνία αγïράς

Date of purchase

Fecha de compra

Date d’achat

Data d’acquisto

Aankoopdatum

Innkjøpsdato

Data de compra

Ostopäivä

Inköpsdatum

machine cadeau?/Er maskinen en gave?/

Recebeu esta ferramenta como presente?/

Ostitko koneen lahjaksi?/Är maskinen en gåva?

Ja/Ja/

Nαι/

Yes/Sí/Oui/Si/Ja/Ja/Sim/

Kyllä/Ja

Nej/Nein/

Oøι/

No/No/Non/No/Nee/Nei/

Não

/

Ei/Nej

Hvor meget kostede maskinen?/Was war der

Preis dieses Werkzeuges?/

Πïιά είναι η τιµή

τïυ εργαλείïυ αυτïύ?/

What was the price of

this tool?/¿Cual fue el precio de esta

herramienta?/Prix payé?/Quanto ha pagato

questo prodotto?/Wat was de prijs van dit

produkt?/Hvor meget kostet maskinen?/Que

preço pagou por esta ferramenta?/Paljonko

kone maksoi?/Hur myket kostade maskinen?

Er dette din førsto B&D maskine?/Ist dieses

Werkzeug-/

Eίναι τï εργαλείï αυτÞ-/

Is this tool-

/¿Es esta herramienta que comprado-/Est-ce-/

Questo prodotto è-/Is deze machine-/Er dette

din første B&D maskin?/Esta ferramenta é-/

Onko tämä ensimmäinen B&D-koneesi?/

Är detta Din första B&D-velu?

Ja/ein Erstkauf?/

η ρώτη σας αγïρά?

/

your first purchase?/la primera de

este tipo?/un ler achat?/il suo primo

acquisto?/uw eerste aankoop?/Ja/a

sua primeira compra?/Kyllä/Ja

Nej/Ersatzkauf?/

για αντικατάσταση?/

a

replacement?/un reempalzo?/un

achat de remplacement?/una

sostituzione?/een vervanging?/Nei/

uma substitução?/Ei/Nej

Forhandler adresse/Händleradresse/

∆ιεύθυνση

αντι ρïσώ ïυ

/Address of dealer/Dirección del

detallista/Cachet du revendeur/Indirizzo del

rivenditore/Dealeradres/Forhandlerens

adresse/Morada do revendedor/Jälleenmyyjän

osoite/Återförsäljarens adress

:

Cat. no. GT_ _ _

Navn/Name/

Oνïµα

/Name/Nombre/Nom/

Nome/Naam/Navn/Nome/Nimi/Namn

:

Adresse/Adresse/

∆ιεύθυνση

Address/

Dirección/Adresse/Indirizzo/Adres/Adresse/

Morada/Osoite/Adress

:

By/Wohnort/

ΠÞλη/

Town/Ciudad/Ville/Cittá/

Plaats/By/Localidade/Paikkakunta/By:

Postnr./Postleitzahl/

KωδικÞς

/Postcode/

Code postal/Código/Codice postale/Postcode/

Postnr./Código postal/Postinumero/Postnr.

:

Er maskinen en gave?/Ist diese Maschine ein

Geschenk?/

H µηøανή είναι δώρï?/

Is this

product a gift?/¿Ha recibido usted esta

herramienta como regalo?/S’agit-il d’un

cadeau?/Si tratto di un regalo?/Kreeg u deze

• Venligst sæt kryds i ruden såfremt De

ikke måtte ønske at modtage information

fra anden virksomhed end Black & Decker.

• Bitte ankreuzen, wenn Sie auch von anderen

Firmen interessantes Informationsmaterial

erhalten möchten. •

Παρακαλείσθε να σηµειώσετε

εάν δέν θέλετε να άρετε ληρïæïρίες άλλης

εταιρείας εκτÞς της Black & Decker.

• Data

protection act: Tick the box if you prefer not to

receive information from us or others. • Señale

en la casilla sino quiere recibir información de

otras empresas. • Si vous ne souhaitez pas

recevoir d’informations de la part d’autres

sociétés que Black & Decker, cochez cette

case. • Barrate la casella se non desiderate

ricevere informazioni da altre aziende.

• A.u.b.dit vakje aankruisen indien u geen

informatie wenst te ontvangen van andere

bedrijven dan Black & Decker. • Vennligst kryss

av dersom De ikke ønsker informasjon fra andre

bedrifter enn Black & Decker. • Por favor,

assinale com uma cruz se desejar receber

informação de outras empresas, além da

Black & Decker. • Merkitkää rasti ruutuun, mikäli

ette halua vastaanottaa informaatiota muulta

taholta kuin Black & Deckeriltä. • Vänligen

kryssa för i rutan om Ni inte vill ha information

från andra företag än Black & Decker.

44

• GARANTI KORT • GARANTIEKARTE •

KAPTA E°° YHΣHΣ

• GUARANTEE CARD • TARJETA DE GARANTÍA • CARTE DE GARANTIE

• TAGLIANDO DI GARANZIA • GARANTIE-KAART • GARANTI KORT • CARTÃO DE GARANTIA • TAKUUKORTTI • GARANTIBEVIS

Australia Call 1900 937766 (max. call charge $2.00 ex. tax) Nederland Florijnstraat 10, 4879 AH Etten-Leur

Belgique/België Weihoek 1, 1930 Zaventem New Zealand Call 0900 97766 (max. call charge $2.00 ex. tax)

Danmark Hejrevang 26B, 3450 Allerød Norge Strømsveien 344, 1081 Oslo

Deutschland Black & Decker Str. 40, D-65510 Idstein Österreich Erlaaer Straße 165, 1231 Wien

Eλλάς Black & Decker Eλλάς, Συγγρïύ 154, 17671 Kαλλιθέα

Portugal Rua Egas, Moniz 173, S. João do Estoril, 2768 Estoril Codex

España 43883 Roda de Barà (Tarragona) South Africa After sales service, PO Box 5303, Johannesburg 2000

France BP21, 69571 Dardilly Cedex Suomi Black & Decker Oy, Rälssitie 7C, 01510 Vantaa

Helvetia Rütistraße 14, 8952 Schlieren, Schweiz/Suisse Sverige Box 603, 421 26 Västra Frölunda

Italia Viale Elvezia 2, 20052 Monza (MI) UK & Ireland PO Box 821, Slough, Berkshire, SL1 3AR

Danmark Venligst klip denne del ud og send frankeret til Black & Decker

i dit land.

Deutsch Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in einen

frankierten Umschlag und schicken ihn direkt an die

Black & Decker Adresse Ihres Landes.

Eλληνικα

Παραρακαλώ κÞψτε αυτÞ τï κïµµάτι και ταøύδρïµήστε τï

αµέσως µετά την αγïρά τïυ ρïιÞντïς σας στην διεύθυνση

της Black & Decker στην ελλάδα (âλέ ε άνω).

English Please cut out this section, put into a stamped addressed

envelope and post immediately after the purchase of your

product to the Black & Decker address in your country (above).

If you live in Australia or New Zealand, please register by phone.

Español Después de haber comprado su herramienta envie usted, por

favor, esta tarjeta a la central de Black & Decker en su país.

Français Découpez cette partie et envoyez-la sous enveloppe timbrée à

l’adresse de Black & Decker dans votre pays (voir ci-dessus),

ceci immédiatement après votre achat.

Italiano Per favore ritagliate questa parte, inseritela in una busta con

francobollo e speditela subito dopo l’acquisto del prodotto

all’indirizzo della Black & Decker nella vostra nazione (vedi sopra).

Nederlands Knip dit gedeelte uit, zend het in een gefrankeerde,

geadresseerde envelop direct na uw aankoop naar het

Black & Decker-adres in uw land (zie boven).

Norge Vennligst klipp ut denne delen umiddelbart etter du har pakket

ut ditt produkt og legg det i en adressert konvolutt til

Black & Decker (Norge) A/S (se adresse over).

Português Por favor, recorte esta parte, coloque-a num envelope selado

e enderessado e envie-0 logo após a compra do seu produto

para o enderesso da Black & Decker do seu país.

Suomi Leikkaa irti tämä osa, laita se oheiseen kuoreen ja postita

kuori yllä olevaan paikalliseen Black & Decker osoitteeseen.

Sverige Var vänlig klipp ur denna del. Skriv Ditt namn och adress på

ett frankerat kuvert, och sind det genast till Black & Deckers

adress i DItt land (se ovan).

Part no. 369162-01 10/96

45

R

English

Italiano

Deutsch

Français

Nederlands

Español

Português

Eλληνικά

Danmark

Suomi

Norge

Sverige

BLACK+DECKER GT259 User manual

This manual is also suitable for

BLACK+DECKER GT259 User manual

in other languages

Related papers

Other documents