Denver BTE-100GREEN User manual

Brand: Denver

Model: BTE-100GREEN

Category: Mobile headsets

Type: User manual

This manual is also suitable for

BTE-100GREY

Instruction Manual

BTE-100

www.facebook.dk/denver-electronics

1.Button instructions:

2. How to use

2.1 General Functions:

Function

instruction

Turn on

Press the button for 3 seconds when the device is off. Blue LED

light slowly flash and a tone voice BEEP)

Enter the pairing mode

In power off mode,press the button and hold on for 6

seconds.(Blue LED and RED LED light quickly flash alternately with two

beep tone voice)..

Pairing

In pairing mode,use a bluetooth function mobile phone or other

bluetooth device to paired.(details refer to the part 2.2)

Play/pause

Press the to play when the device is pausing and press to

pause when the device is playing

Volume up

Long press is for volume up

Volume down

Long press is for volume down

Press is for previours music.

Press is for next music

Turn off

Press the button for 3 seconds when the device is ON.(a tone

voice Beep and all LED is off).

Low battery warning

(the red LED light flashes)

Charging

Plug the charger to port of the device.(red LED light is on).

Answer call

Press the button for 1 second while the call coming.

End call

Press the button for 2 seconds to reject call when the call is

ringing.

2.2 Pairing with Mobile phone or other device

To use your bluetooth earphones, you have to pair them with mobile phone or PC. If your bluetooth

earphones has been paired already, they will pair automatically when within range.

How to pair with phone

·Turn on your phone and ensure Bluetooth function is active.

·Turn on the Bluetooth earphones & go to the pairing mode

·Search after Bluetooth devices on your phone by following the phones’s instructions. Refer to your

phone’s user manual for more information.

·After a few seconds the phone will list the names of active Bluetooth units. Choose “BTE-100”.

·Your phone might ask for a password, if so, enter 0000(4 zero).

· Your phone will confirm the pairing, and you are then ready to use the earphones.

How to pair with computer

· If your PC does not have Bluetooth, you can use a Bluetooth USB adapter (not included)

·Turn on Bluetooth earphones & go to the pairing mode.

· Open the Bluetooth menu installed on your PC, and search after Bluetooth devices. (refer to user

manual of the PC for more information.)

·After a few seconds”BTE-100” will will show on the list of active Bluetooth units. Choose this and

choose “connect”.

·Your PC will now connect, and you are then ready to use the earphones.

2.3 charge your earphones.

The earphones are charged by MicroUSB, either connected to a USB port in a PC, or using an

external USB charger (not incl.) Full charge takes approximately 2.5 hour. When the earphones are

fully charged, the LED will turn off.

3. Technical specification:

Parameter

specification

Bluetooth version

V4.1

Bluetooth profiles

Support A2DP1.2,AVRCP1.0,HFP1.5,HSP1.0A2DP1.2,AVRCP1.0,HFP1.5,HSP1.0

RF range

10m

Frequency

response

80Hz-20KHz

Loudspeaker

output

10mW

Signal-To-Noise

≥80dB

Distortion

≤5.0%

Playback time

6 hours

Charging time

2.5 hours

4. FAQ

1. The earphones cannot turn on?

Answer: Please ensure the battery is properly charged. This can take up to 2.5 hours. The LED light

will turn on when charging, and turn off when fully charged.

2. There is no sound in the earphones?

Answer: Check the connection between your earphones and the phone or PC. If the connection has

been lost, please pair again.

Electric and electronic equipment and included batteries contains materials,

components and substances that can be hazardous to your health and environment,

if the waste material (discarded electric and electronic equipment and batteries) is

not handled correctly.

Electric and electronic equipment and batteries is marked with the crossed out trash can symbol,

seen below. This symbol signifies that electric and electronic equipment and batteries should

not be disposed with other household waste, but should be disposed of separately.

As the end user it is important that you submit your used batteries to the appropriate and

designated facility. In this manner you make sure that the batteries are recycled in accordance

with legislature and will not harm the environment.

All cities have established collection points, where electric and electronic equipment and

batteries can either be submitted free of charge at recycling stations and other collection sites,

or be collected from the households. Additional information is available at the technical

department of your city.

Hereby, Inter Sales A/S, declares that this product is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of

conformity may be

obtained at:

Inter Sales A/S, Stavneagervej 22, DK-8250 Egaa, Denmark.

Importer:

DENVER ELECTRONICS A/S

Stavneagervej 22

DK-8250 Egaa

Denmark

www.facebook.com/denverelectronics

Denver BTE-100GREEN User manual

Brand: Denver

Model: BTE-100GREEN

Category: Mobile headsets

Type: User manual

This manual is also suitable for

BTE-100GREY

Download PDF

report

Denver BTE-100GREEN User manual

This manual is also suitable for

Denver BTE-100GREEN User manual

Related papers

Other documents