OWNER’S MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
SK5R (SK5R, SPK5B-W), SPJ4-S(SPJ4-S, S65S3-S)
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
www.lg.com
1 Getting Started
Getting Started2
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufcient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: No naked ame sources, such as lighted
candles, should be placed on the apparatus.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
Getting Started 3
Getting Started
1
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In
case of an emergency, the Power Plug must
remain readily accessible. Check the specication
page of this owner’s manual to be certain of the
current requirements. Do not overload wall outlets.
Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
device, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
NOTICE: For safety marking information including
product identication and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
This device is equipped with a portable battery or
accumulator.
How to Safely remove the batteries or the
battery pack from the equipment: To Remove the
old batteries or battery pack, follow the assembly
steps in reverse order. To prevent contamination of
the environment and bring on possible threat to
human and/or animal health, the old batteries or the
battery pack must be put in an appropriate container
at designated collection points. Do not dispose
of batteries or battery pack together with other
waste. It is recommended that you use local, free
reimbursement systems batteries or battery packs,
(may not be available in your area). The batteries or
the battery pack should not be exposed to excessive
heat such as sunshine, re or the like.
CAUTION: Only use the AC adapter supplied with
this device. Do not use a power supply from another
device or another manufacturer. Using any other
power cable or power supply may cause damage to
the device and void your warranty.
Getting Started4
Getting Started
1
Symbols
~
Refers to alternating current (AC).
0
Refers to direct current (DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to
you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of
media, shipping and handling) upon email request to
opensourc[email protected].
This offer is valid for a period of three years after our
last shipment of this product. This offer is valid to
anyone in receipt of this information.
Table of Contents 5
1
2
3
4
5
Table of Contents
1 Getting Started
2 Safety Information
6 Unique features
6 Introduction
6 – Symbols used in this manual
7 Remote control
8 Front panel
8 Rear panel
9 About LED condition
11 Installing the sound bar
11 Mounting the main unit on a wall
13 Positioning the speakers
2 Connecting
14 Organizing cables (Optional)
14 Connecting the AC Adapter
15 Wireless subwoofer and rear speaker
connection
16 – Rear speakers connection
17 – Surround sound
19 – How to Affix the Ferrite Core
20 Connecting to your TV
20 – Using an OPTICAL cable
20 – LG Sound Sync
21 – Using an HDMI cable
22 – Additional information for HDMI
23 Optional equipment connection
23 – HDMI connection
24 – OPTICAL IN connection
25 – PORTABLE IN connection
25 – USB connection
25 – Compatible USB devices
26 – USB device requirement
26 – Playable file
3 Operating
28 Basic operations
28 – USB operation
28 Other operations
28 – Turn off the sound temporarily
28 – Using your TV remote control
29 – Auto power down
29 – AUTO POWER On/Off
30 – Auto function change
30 – Quick Start
31 Using BLUETOOTH® technology
31 – Listening to music stored on the
BLUETOOTH devices
33 Using BLUETOOTH App
33 – Install “Music Flow Bluetooth” App onto
Your BLUETOOTH Device
33 – Activate BLUETOOTH with “Music Flow
Bluetooth” App
35 Sound adjustment
35 – Setting sound effect
35 – Adjust the woofer level settings
35 – Adjust the rear speakers level settings
4 Troubleshooting
36 Troubleshooting
36 – General
37 – NOTES to use wireless
38 – NOTES to release Demo mode
5 Appendix
39 Trademarks and licenses
40 Specifications
42 Maintenance
42 – Handling the unit
Getting Started6
Getting Started
1
Unique features
Auto power down
This unit will turn off by itself for energy saving
consumption.
LG Sound Sync
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
BLUETOOTH®
Listens to music stored on your Bluetooth device.
Surround sound
You can enjoy surround sound by using Wireless Rear
Speaker kit. (SPJ4-S)
Introduction
Symbols used in this manual
,
Note
Indicates special notes and operating features.
>
Caution
Indicates cautions for preventing possible damages
from abuse.
Getting Started 7
Getting Started
1
Remote control
Replacement of Battery
Remove the battery cover on the rear of the remote
control, and insert the battery with and
matched correctly.
• • • • • • • • • • • • • •
a
• • • • • • • • • • • • •
1
(Standby) : Switches the unit ON or OFF.
VOL (Volume)
o
/
p
: Adjusts speaker volume.
F (Function) : Selects the function and the input
source.
[
(Mute) : Mutes the sound.
C/V
(Skip/Search) :
- Skips Fast backward or Forward.
- Searches for a section within a le.
N
(Play/Pause) : Starts playback. / Pauses playback.
• • • • • • • • • • • • • •
b
• • • • • • • • • • • • •
ASC : Analyzes the property of input sound and
provides the sound optimized for the content in real
time.
DTS V:X :
- Selects cinematic surround sound.
- Turns off using your tv remote control function
(Page 26)
BASS BLAST :
- Selects reinforced bass sound.
- Turns on using your tv remote control function
(Page 26)
REAR
o
/
p
:
- Adjusts sound level of rear speakers.
- Turns on or off Surround function. (Page 16)
WOOFER
o
/
p
: Adjusts sound level of subwoofer.
AUTO POWER ON/OFF :
- Turns on or off AUTO POWER function.
(Page 29)
- Turns on or off the Bluetooth connection lock.
(Page 32)
Getting Started8
Getting Started
1
A
Remote sensor
B
Standby LED (Red)
C
Function LED (White)
D o/p
(Volume) : Adjusts volume level
F (Function) : Selects the function and input
source.
1
(Standby) : Switches the unit ON or OFF.
Front panel
A
DC IN : Connect to the AC adapter
B
OPTICAL IN : Connect to an Optical device
C
PORTABLE IN : Connect to a Portable device
D
USB
: Connect to a USB device
E
HDMI OUT (TV ARC) : Connect to a TV
F
HDMI IN : Connect to HDMI out on a device
Rear panel
Getting Started 9
Getting Started
1
About LED condition
: LED is staying on. : LED is blinking. : LED is off.
LED Condition Description
OPTICAL LED turns on. OPTICAL function is selected.
OPTICAL LED blinks twice and
turns on.
LG Sound Sync (Optical) function is
selected.
USB LED turns on. USB function is selected.
USB LED blinks. Paused USB playback.
BT (Bluetooth) LED turns on. Paired with Bluetooth device.
BT (Bluetooth) LED blinks. Waiting for Bluetooth connection.
LG TV LED turns on.
LG Sound Sync (Wireless) function is
selected.
HDMI IN
LED turns on. HDMI IN function is selected.
LG TV and HDMI IN LEDs turn
on.
PORTABLE function is selected.
USB and BT (Bluetooth) LEDs
turn on.
ARC function is selected
y
When you press any button, standby LED (Red) on the main unit blinks.
y
When you press
[
(Mute) button, standby LED (Red) blinks slowly.
y
When this unit reaches minimum volume, standby LED (Red) turns on for 2 seconds and blinks slowly.
y
When this unit reaches maximum volume, standby LED (Red) turns on for 2 seconds.
y
When you press volume (
o
/
p
) button continually, standby LED (Red) blinks quickly.
,
Note
Getting Started10
Getting Started
1
Useful functions for using the unit.
Function Description To do Do this
TV Remote On/
Off
(Page 28)
It allows you to control the
volume of this unit by your TV
remote control even by other
company’s product.
Initial setting of this function
was set to on.
ON Press and hold BASS BLAST on the remote
control for about 2 seconds.
The standby LED blinks once.
OFF Press and hold DTS V:X on the remote
control for about 2 seconds.
The standby LED blinks once.
BT Lock On/Off
(Page 32)
It allows you to connect a
Bluetooth deivce only on
Bluetooth and LG TV functions.
Initial setting of this function
was set to off.
ON Press and hold AUTO POWER ON on the
remote control for about 2 seconds in
Bluetooth function.
The standby LED blinks once.
OFF Press and hold AUTO POWER OFF on
the remote control for about 2 seconds in
Bluetooth function.
The standby LED blinks once.
Auto Power
On/Off
(Page 29)
It allows the unit to turn on
and off automatically by input
signals :
Optical, LG TV or Bluetooth
Initial setting of this function
was set to on.
ON Press AUTO POWER ON on the remote
control.
The standby LED blinks once.
OFF Press AUTO POWER OFF on the remote
control.
The standby LED blinks once.
Surround On/
Off
(Page 17)
It allows you to enjoy surround
sound with rear speakers.
Initial setting of this function
was set to off.
ON Pess REAR
o
on the remote control for
about 2 seconds.
The standby LED blinks once.
OFF Pess REAR
p
on the remote control for
about 2 seconds.
The standby LED blinks once.
Getting Started 11
Getting Started
1
Installing the sound bar
You can hear the sound by connecting the unit to the
other device : TV, Blu-ray disc player, DVD player, etc.
Place the unit in front of the TV and connect it to the
device you want. (Page 14 - 26)
y
For best performance of wireless connection
such as Bluetooth or wireless subwoofer,
do not install the unit on Metallic furniture
because wireless connection communicates
through a module positioned on the bottom
of the unit.
y
Be careful not to make scratches on the
surface of the Unit / Subwoofer when
installing or moving them.
>
Caution
Mounting the main unit
on a wall
You can mount the main unit on a wall.
Because it is difcult to make a connection after
installing this unit, you should connect the cables
before installation.
>
Caution
Preparation materials
Unit
Wall bracket install guide
Screws
Screws (A)
Wall plug
Wall bracket
(Not supplied)
Getting Started12
Getting Started
1
1. Match the TV’s BOTTOM EDGE of Wall bracket
install guide with the bottom of TV and attach to
the position.
2. When you mount it on a wall (concrete), use the
wall plugs. You should drill some holes. A guide
sheet (Wall bracket install guide) is supplied to
drill. Use the sheet to check the point to drill.
3. Remove the Wall bracket install guide.
4. Fix the brackets with screws (A) as shown in the
illustration below.
Screws (A) and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting.
,
Note
5. Put the unit on the brackets to match screw
holes on the bottom of the unit.
6. Fix the unit with the screws firmly.
To detach the unit, perform it in reverse order.
,
Note
Getting Started 13
Getting Started
1
y
Do not install this unit upside down. It can
damage the parts of this unit or be the cause
of personal injury.
y
Do not hang onto the installed unit and avoid
any impact to the unit.
y
Secure the unit rmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
y
When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
>
Caution
Positioning the speakers
For the best surround sound, place the speaers as
shown below.
2 Connecting
Connecting14
Connecting
2
Organizing cables
(Optional)
You can organize the cable with cable ties.
1. Hold the cables together with cable ties as shown
below.
2. Tighten cable ties.
y
After all connections are completed, you can
arrange cables as needed.
y
Cable ties is not supported.
,
Note
Connecting the AC
Adapter
Connect the speaker to the power supply with the
supplied AC adapter.
1. Connect the supplied AC power cord to the AC
adapter.
2. Connect the AC adapter cable to DC IN adapter
input.
3. Plug the AC power cord into an AC outlet.
Only use the AC adapter supplied with this
device. Do not use a power supply from another
device or manufacturer. Using any other power
cable or power supply may cause damage to the
device and void your warranty.
>
Caution
Connecting 15
Connecting
2
Wireless subwoofer and
rear speaker connection
LED indicator of wireless subwoofer
LED Color Status
Green
(Blink)
Attempting to make connection.
Green The connection is completed.
Red The wireless subwoofer is in
standby mode or the connection
is failed.
Off
(No display)
The power cord of wireless
subwoofer is disconnected.
Setting up the wireless subwoofer for
the first time
1. Connect the power cord to the subwoofer and
plug the power cord into a power outlet.
2. Turn on the main unit : The sound bar and wireless
subwoofer will be automatically connected.
- Green LED on the rear of wireless subwoofer
turns on.
Manually pairing wireless subwoofer
When your connection is not completed, you can
check red LED on the wireless subwoofer and the
wireless subwoofer does not make sound. To solve
the problem, follow the steps below.
1. Press Pairing button on the rear of the wireless
subwoofer.
- The green LED on the rear of the wireless
subwoofer blinks quickly. (If the green LED
does not blink, press and hold the Pairing
button.)
2. Turn on the main unit.
3. Pairing is completed.
- The green LED on the rear of the wireless
subwoofer turns on.
Connecting16
Connecting
2
y
It takes a few seconds (and may take longer)
for the main unit and the subwoofer to
communicate with each other and make
sounds.
y
The closer the main unit and the subwoofer,
the better sound quality. It is recommended
to install the main unit and the subwoofer as
close as possible and avoid the cases below.
- There is an obstacle between the main
unit and the subwoofer.
- There is a device using same frequency
with this wireless connection such as
a medical equipment, a microwave or a
wireless LAN device.
- Keep the sound bar and the subwoofer
away from the device (ex. wireless router,
microwave oven, etc.) over 1m to prevent
wireless interference.
!
1 m
,
Note
Rear speakers connection
Connecting the rear speakers
1. Connect the black stripe wire to the terminal
marked - (minus) and the other end to the
terminal marked + (plus).
2. Connect the wireless receiver and the rear
speakers (right, left) with the speaker cables.
Color Position
Grey Rear right
Blue Rear left
Rear Speaker
(Left)
Rear Speaker
(Right)
Connecting 17
Connecting
2
y
Use the speaker supplied with this unit
only. Using any other speaker may cause
malfunction.
y
Be sure to match the speaker cable to the
appropriate terminal on the components: +
to + and – to –. If the cables are reversed, the
sound will be distorted and will lack bass.
>
Caution
LED indicator of wireless receiver
LED Color Status
Yellow - green The wireless receiver is receiving
the signal from the sound bar.
Red The wreless receiver is in standby
mode.
Off
(No display)
The power cord of wireless
receiver is disconnected.
Setting up the wireless receiver for the
first time
1. Connect the power cord to the wireless receiver
to the outlet.
2. Turn on the main unit : The sound bar and wireless
receiver will be automatically connected.
- Yellow - green LED on the wireless receiver
turns on.
Manually pairing wireless receiver
When your connection is not completed, you can
see the red LED on the wireless receiver and rear
speakers are not made sound. To solve the problem,
follow the below steps.
1. Press PAIRING button on the rear of the wireless
receiver.
- The yellow - green LED on the wireless receiver
blinks quickly.
2. Turn on the main unit
3. Paring is completed.
- The yellow - green LED on the wireless receiver
turns on.
Surround sound
You can enjoy magnificent surround sound for all the
input sound source with rear speakers.
If you turn on the surround function, the whole
speaker outputs sound.
When you turn off the surround function, the
speakers output sound as an original input sound
channel.
To turn on surround function, press and hold
REAR
o
button for about 2 seconds.
To turn off surround function, press and hold
REAR
p
button for about 2 seconds
BASS BLAST or STANDARD sound effects may
be applied differently depending on regional
option.
,
Note
Connecting18
Connecting
2
Surround function ON
Sound Effect Input
Output
No rear speakers Rear speakers connected
ASC
2.0 Ch
5.1 Ch
STANDARD
2.0 Ch
5.1 Ch
BASS BLAST
or
BASS BLAST +
2.0 Ch
5.1 Ch
DTS V:X
2.0 Ch
5.1 Ch
Surround function OFF
Sound Effect Input
Output
No rear speakers Rear speakers connected
ASC
2.0 Ch
5.1 Ch
STANDARD
2.0 Ch
5.1 Ch
BASS BLAST
or
BASS BLAST +
2.0 Ch
5.1 Ch
DTS V:X
2.0 Ch
5.1 Ch
Connecting 19
Connecting
2
How to Affix the Ferrite Core
Ferrite core may not be provided depending on each
nation’s regulations.
Affix the Ferrite Core for speaker
cables
You must afx a ferrite core in order to reduce or
eliminate electrical interference.
1. Pull the stopper [a] of the ferrite core to open.
2. Wind the speaker cables around the ferrite core
twice.
3. Close the ferrite core until it clicks.
y
If there is a strong electromagnetic wave
product nearby, interference may occur. Put
the main unit and wireless receiver away from
there.
y
The wireless receiver will automatically switch
to standby mode in a few minutes after the
sound bar is turned off.
When the wireless reciever is in standby
mode, the LED will turn on in red.
y
When you turn on the sound bar, the wireless
receiver will turn on and the LED will change
to yellow - green and then the rear speakers
makes sound within a few seconds.
y
It takes a few seconds (and may take longer)
for the main unit and Wireless Receiver to
communicate with each other.
y
Use the rear speaker at least 30 cm away
from either TV screen or PC monitor.
y
When the wireless receiver is being
connected or disconneced with the main unit,
output sound is maybe interrupted.
y
Set the distance between the sound bar and
the wireless receiver as close as possible and
keep them away from the device (ex. wireless
router, microwave oven, etc.) over
1 m to prevent wireless interference.
!P
,
Note
Connecting20
Connecting
2
Connecting to your TV
Please connect this unit and the TV using the optical
digital cable or HDMI cable considering the capability
of the TV.
Using an OPTICAL cable
1. Connect the OPTICAL IN jack on the back of the
unit to OPTICAL OUT jack on the TV using an
OPTICAL cable.
Optical
cable
2. Select the input source to OPTICAL by pressing F
button on the remote control or unit repeatedly.
y
Before connecting the optical cable, be sure
to remove the protection plug cover if your
cable has the cover.
y
You can enjoy the TV audio through the
speakers of this unit. In the case of some TV
models, you must select the external speaker
option from the TV menu. (For details,
reference your TV user manual.)
y
Set up the sound output of TV to listen to
the sound through this unit :
TV setting menu
[
[Sound]
[
[TV Sound
output]
[
[External speaker (Optical)]
y
Details of TV setting menu vary depending
on the manufacturers or models of your TV.
y
If this unit is connected by OPTICAL and ARC
at the same time, the ARC signal is a high
priority.
,
Note
LG Sound Sync
You can control some functions of this unit by
your TV's remote control with LG Sound Sync. It is
compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo on
your TV.
Controllable function by LG TV's remote control :
Volume up/down, mute
Refer to the TV's instruction manual for the details
of LG Sound Sync.
Make one of the following connections, depending on
the capabilities of your equipment.
y
You can also use the remote control of this
unit while using LG Sound Sync. If you use TV's
remote control again, the unit synchronizes
with the TV.
y
When the connection fails, make sure of the
condition of the TV and power.
y
Make sure of the condition of this unit and
the connection in the cases below when using
LG Sound Sync.
- The unit is turned off.
- Changing the function to the others.
- Disconnecting the optical cable.
- Disconnecting the wireless connection
caused by interference or a distance.
y
The amount of time to turn off this unit is
different depending on your TV when you set
AUTO POWER function to ON.
y
Details of TV setting menu vary depending on
the models of your TV.
,
Note
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
