Maytag MLE20PDAYW0 User manual

Maytag Commercial

Stacked Washer/Dryer

SERVICE MANUAL

MLE20PDAYW0

MLG20PDAWW0

MLE20PDAZW0

W10376697

TECHNICAL EDUCATION

MODELS:

MLE20PRAYW0

MLG20PRAWW0

MLE20PRAZW0

ii

WHIRLPOOL CORPORATION assumes no responsibility

for any repairs made on our products by anyone other than

authorized Commercial Laundry Service Professionals.

FORWARD

This Service Manual, (Part No. W10376697), provides the Commercial Laundry

Service Professional with information on the installation, operation, and service of the

Maytag Commercial Stacked Washer/Dryer. For specic information on the model

being serviced, refer to the “Installation Instructions,” or “Tech Sheet” provided with

the washer/dryer. The Wiring Diagrams used in this Service Manual are typical and

should be used for training purposes only. Always use the Wiring Diagram supplied

with the product when servicing the washer.

GOALS AND OBJECTIVES

The goal of this Service Manual is to provide information that will enable the

Commercial Laundry Service Professional to properly diagnose malfunctions

and repair the Maytag Commercial Stacked Washer/Dryer. The objectives of this

Service Manual are to:

Understand and follow proper safety messages.

Understand and diagnose improper installations.

Successfully troubleshoot and diagnose malfunctions.

Successfully perform necessary repairs.

Successfully return the washer/dryer to its proper operational status.

•

iii

TABLE OF CONTENTS

View entire service video .................................................................................................. viii

Links to documents ........................................................................................................... viii

GENERAL ................................................................................................................................. 1-1

Model number designations .............................................................................................. 1-2

Serial number designations .............................................................................................. 1-2

Model & serial number label and tech sheet location ....................................................... 1-3

Stacked washer/dryer specications ................................................................................ 1-4

Warranty ........................................................................................................................... 1-5

INSTALLATION REQUIREMENTS ...........................................................................................

2-1

Tools and parts ................................................................................................................. 2-1

Alternate parts .................................................................................................................. 2-2

Accessories ...................................................................................................................... 2-2

Dimensions ....................................................................................................................... 2-3

Clearances ........................................................................................................................ 2-3

Stacked washer/gas dryer location requirements ............................................................. 2-4

Stacked washer/gas dryer electrical requirements ........................................................... 2-6

Stacked washer/gas dryer gas supply .............................................................................. 2-8

Stacked washer/electric dryer location requirements ....................................................... 2-9

Stacked washer/electric dryer installation clearances ...................................................... 2-10

Stacked washer/electric dryer electrical requirements ..................................................... 2-11

Dryer venting requirements .............................................................................................. 2-14

Dryer gas supply requirements ......................................................................................... 2-18

Gas pipe chart (Natural gas) ............................................................................................. 2-20

Washer drain system ........................................................................................................ 2-21

Stacked washer/dryer maintenance instructions .............................................................. 2-22

Remove shipping bolts ..................................................................................................... 2-25

Reinstall shipping bolts ..................................................................................................... 2-25

BASIC OPERATION .................................................................................................................

3-1

Electronic control setup instructions ................................................................................. 3-1

General user information .................................................................................................. 3-2

Control set-up procedure .................................................................................................. 3-4

Using the buttons to program the controls ........................................................................ 3-4

Start operating set-up ....................................................................................................... 3-5

Set-up codes ..................................................................................................................... 3-5

Theory of operation ........................................................................................................... 3-9

Air intake and exhaust ...................................................................................................... 3-10

Typical cycle of operation ................................................................................................. 3-11

Understanding the gas valve and ignition system ............................................................ 3-13

Cleaning the dryer location ............................................................................................... 3-14

Cleaning the lint screen .................................................................................................... 3-14

Cleaning the dryer interior ................................................................................................ 3-15

Removing accumulated lint ............................................................................................... 3-15

Vacation and moving care ................................................................................................ 3-15

Page

iv

COMPONENT ACCESS ........................................................................................................... 4-1

Remove chemical dispenser drawer and parts ................................................................. 4-1

Remove control panel ....................................................................................................... 4-3

Remove control board ...................................................................................................... 4-4

Remove user interface display lens .................................................................................. 4-5

Install card reader ............................................................................................................. 4-5

Remove payment system facia ......................................................................................... 4-6

Remove coin drop ............................................................................................................. 4-6

Remove coin vault and coin vault switch .......................................................................... 4-7

Remove service switch assembly ..................................................................................... 4-8

Remove keypad assembly ................................................................................................ 4-9

Remove control panel bracket .......................................................................................... 4-10

Remove dryer from stack .................................................................................................. 4-11

Remove water inlet valves ................................................................................................ 4-12

Remove water inlet valves from back without removing dryer .......................................... 4-13

Remove chemical dispenser assembly ............................................................................ 4-14

Remove pressure switch .................................................................................................. 4-16

Remove RFI line lter ....................................................................................................... 4-17

Remove drain hose and tting .......................................................................................... 4-18

Remove washer power cord (MLE model only) ................................................................ 4-19

Remove door lock / switch assembly ................................................................................ 4-20

Remove door hook ........................................................................................................... 4-22

Remove door and hinge assembly ................................................................................... 4-22

Washer door parts and disassembly ................................................................................. 4-23

Remove stacked washer/dryer base ................................................................................ 4-25

Remove washer lower service panel ................................................................................ 4-26

Remove drain pump ......................................................................................................... 4-27

Remove drain pump motor ............................................................................................... 4-29

Remove tub to pump hose ................................................................................................ 4-30

Remove ground switch ..................................................................................................... 4-31

Remove washer central control unit (CCU) ...................................................................... 4-33

Washer CCU connections ................................................................................................. 4-34

Remove motor control unit (MCU) .................................................................................... 4-35

Remove washer rear panel ............................................................................................... 4-36

Remove washer drive belt ................................................................................................ 4-37

Remove basket pulley ...................................................................................................... 4-38

Remove vent tube ............................................................................................................. 4-39

Remove temperature sensor ............................................................................................ 4-40

Remove motor .................................................................................................................. 4-41

Remove air gap damper ................................................................................................... 4-42

Remove washer front panel .............................................................................................. 4-43

Remove UIC transformer .................................................................................................. 4-44

Remove the bellow ........................................................................................................... 4-44

Remove washer front support bracket .............................................................................. 4-46

TABLE OF CONTENTS - CONTINUED

Page

v

Remove tub and spin basket assembly ............................................................................ 4-47

Replace washer bafe ...................................................................................................... 4-50

Washer side panels and base ........................................................................................... 4-51

Remove dryer console cover ............................................................................................ 4-52

Remove dryer control board (CCU) .................................................................................. 4-53

Dryer CCU connections .................................................................................................... 4-54

Remove dryer door and hinge assembly .......................................................................... 4-55

Reverse a dryer door ........................................................................................................ 4-56

Remove dryer door handle ............................................................................................... 4-58

Remove dryer inner door lens .......................................................................................... 4-58

Remove dryer drum light lens ........................................................................................... 4-59

Remove dryer front panel ................................................................................................. 4-60

Remove dryer lint lter housing ........................................................................................ 4-61

Remove dryer front bulkhead ........................................................................................... 4-62

Remove dryer outlet grill ................................................................................................... 4-63

Remove dryer front support rollers and shafts .................................................................. 4-64

Remove dryer top panel ................................................................................................... 4-65

Remove dryer console bracket ......................................................................................... 4-66

Remove dryer belt ............................................................................................................ 4-67

Remove dryer drum .......................................................................................................... 4-68

Remove a dryer bafe ...................................................................................................... 4-69

Remove dryer thermistor .................................................................................................. 4-70

Remove dryer thermal fuse .............................................................................................. 4-70

Remove dryer blower wheel ............................................................................................. 4-71

Remove dryer blower housing .......................................................................................... 4-72

Remove dryer exhaust duct .............................................................................................. 4-73

Remove dryer motor and speed increaser ....................................................................... 4-74

Remove dryer motor bracket ............................................................................................ 4-76

Remove dryer belt switch ................................................................................................. 4-77

Remove dryer idler pulley ................................................................................................. 4-77

Remove drum rear support rollers .................................................................................... 4-78

Remove rear support roller shafts .................................................................................... 4-78

Remove rear panel ........................................................................................................... 4-79

Remove dryer side panel (left side shown) ....................................................................... 4-80

Remove rear bulkhead ..................................................................................................... 4-81

Remove heat plenum ........................................................................................................ 4-81

Remove ame sensor ....................................................................................................... 4-82

Remove high temp thermostat .......................................................................................... 4-82

Remove high temp cutout ................................................................................................. 4-83

Remove ignitor .................................................................................................................. 4-83

Remove gas valve coils .................................................................................................... 4-84

Remove gas burner assembly .......................................................................................... 4-84

Remove gas valve from bracket ....................................................................................... 4-85

Remove electric heating element ..................................................................................... 4-86

TABLE OF CONTENTS - CONTINUED

Page

vi

Remove heater coil ........................................................................................................... 4-87

COMPONENT TESTING ...........................................................................................................

5-1

Inlet valve solenoids ......................................................................................................... 5-1

Pressure switch ................................................................................................................ 5-2

RFI line lter ...................................................................................................................... 5-3

Door lock assembly .......................................................................................................... 5-4

Drain pump motor ............................................................................................................. 5-5

Temperature sensor ..........................................................................................................5-6

Drive motor ....................................................................................................................... 5-7

Ground switch ................................................................................................................... 5-7

User interface membrane switch ...................................................................................... 5-8

Coin drop acceptor ........................................................................................................... 5-9

Transformer ...................................................................................................................... 5-10

Gas valve coils .................................................................................................................. 5-11

Burner ignitor .................................................................................................................... 5-12

Manometers ...................................................................................................................... 5-12

Flame sensor .................................................................................................................... 5-14

High temp thermostat & High temp cutout (gas dryers only) ............................................ 5-14

Heating element (electric dryers only) .............................................................................. 5-15

High temp cutout (electric dryers only) ............................................................................. 5-16

Centrifugal switch ............................................................................................................. 5-17

Drive motor ....................................................................................................................... 5-18

Thermistor ......................................................................................................................... 5-20

Thermal fuse ..................................................................................................................... 5-21

Transformer ...................................................................................................................... 5-22

DIAGNOSIS & TROUBLESHOOTING .....................................................................................

6-1

Diagnostic mode ............................................................................................................... 6-1

Failure displays ................................................................................................................. 6-2

Dryer diagnostic codes ..................................................................................................... 6-2

Washer diagnostic codes .................................................................................................. 6-3

Washer quick overview test .............................................................................................. 6-8

Washer manual overview test ........................................................................................... 6-9

Diagnostic test quick guide ............................................................................................... 6-10

Washer help codes ........................................................................................................... 6-11

Dryer help codes ............................................................................................................... 6-11

Help mode submenu ......................................................................................................... 6-12

Help mode symbols and elements .................................................................................... 6-13

Help mode keypad function table ..................................................................................... 6-13

Washer pump motor continuity test .................................................................................. 6-14

Washer motor ohm test ..................................................................................................... 6-14

Transformer connector ...................................................................................................... 6-14

Water temperature sensor ................................................................................................ 6-14

Cycle temperature selections ........................................................................................... 6-14

TABLE OF CONTENTS - CONTINUED

Page

vii

Water valve locations ........................................................................................................ 6-15

Washer CCU wire harness connector table ...................................................................... 6-15

Manually unlocking the door latch .................................................................................... 6-15

Manually unlatching tripped door latch ............................................................................. 6-15

Washer care ...................................................................................................................... 6-16

Electronic assemblies removal or replacement ................................................................ 6-16

Washer clean-out cycle procedure ................................................................................... 6-17

Washer troubleshooting guide .......................................................................................... 6-18

Dryer troubleshooting guide .............................................................................................. 6-19

Troubleshooting tests ........................................................................................................ 6-20

Unusual sounds ................................................................................................................ 6-28

Dryer displaying code message ........................................................................................ 6-29

Troubleshooting dryer results ........................................................................................... 6-30

Clothes are not drying satisfactorily, drying times too long, or load is too hot ............. 6-30

Lint on load.................................................................................................................. 6-31

Stains on load or drum ................................................................................................ 6-31

Loads are wrinkled ...................................................................................................... 6-31

Odors .......................................................................................................................... 6-31

WIRING DIAGRAMS .................................................................................................................

7-1

U.S. electric ...................................................................................................................... 7-1

U.S. gas ............................................................................................................................ 7-2

Canada electric ................................................................................................................. 7-3

Canada gas ...................................................................................................................... 7-4

TABLE OF CONTENTS - CONTINUED

Page

viii

INTERACTIVE SERVICE MANUAL INSTRUCTIONS

Click the mouse on any topic in the table of contents to go directly to that section.

Click the mouse on any link that says (See page ?-?) to go directly to the page referenced.

Click the mouse on any button in the links section to open the attached document.

This symbol means a video clip is available. Click the mouse on the camera icon

to view the video. To close the movie, click the X box at the top corner of the video window.

System requirements to view the video clips in this manual are:

Windows 2000 or higher, Adobe

®

Acrobat

®

Reader

®

version 6 or higher,

Windows Media Player for PC and Quicktime Player for Macintosh computers.

LINKS TO DOCUMENTS

VIEW ENTIRE SERVICE VIDEO

1-1

GENERAL

IMPORTANT

Electrostatic Discharge (ESD)

Sensitive Electronics

ESD problems are present everywhere. ESD may damage or weaken

the electronic control assembly. The new control assembly may appear

to work well after repair is nished, but failure may occur at a later date

due to ESD stress.

• Use an anti-static wrist strap. Connect wrist strap to green ground

connection point or unpainted metal in the appliance

-OR-

Touch your nger repeatedly to a green ground connection point or

unpainted metal in the appliance.

• Before removing the part from its package, touch the anti-static bag

to a green ground connection point or unpainted metal in the

appliance.

• Avoid touching electronic parts or terminal contacts; handle

electronic control assembly by edges only.

• When repackaging failed electronic control assembly in anti-static

bag, observe above instructions.

STACKED WASHER / DRYER SAFETY

1-2

n

Horizontal

Axis Washer Non-Pedestal

Horizontal Axis Washer w/Pedestal

1-2

MODeL nuMBer M LG 20 PD a G W 0

B

ranD

M

Maytag

D

riVe TYPe

HN

PrODuCT

30 Commercial HE Front Load Washer Starts in 2011

COnTrOL TYPe

PD

Processor Coindrop

PR Processor Reader

PN Processor Non-coin

CS Mechanical Coinslide

MN Mechanical Non-coin

M

arKeTinG CODe

A

First series

B Second series

VOL

T

aGe CODe

W 120V

-60Hz (US)

X

120V

-60Hz (Canada)

G

220-240V

-50Hz (Export Models)

COLO

r

W White

enGineerinG CHanGe (nuMeriC)

MODeL nuMBer DeSiGnaTiOnS

SeriaL nuMBer DeSiGnaTiOnS

SeriaL nuMBer M

1 35 10901

D

iViSiOn reSPOnSiBiLiTY

M

Marion, Ohio

HL Monterrey

, MX

Y

ear OF PrODuCTiO

W

2008

Y

2009

0

2010

1

201

1

W

eeK OF PrODuCTiOn

35 35th W

eek in the calendar year

M

anuFaCTurinG SeQuenCe nuMBer

HP

AH

Automatic Horizontal

Axis Washer

22

Commercial HE Front Load W

asher Ends in 2011

2013

2014

3

4

2015

5

C Clyde, Ohio

LG

Commercial Stacked Washer/Dryer

6 2016

7 2017

8 2018

9 2019

12 2 20

MODEL NUMBER DESIGNATIONS

SERIAL NUMBER DESIGNATIONS

1-3

Location of Model & Serial Number Label

Location of Tech Sheet, Parts List, Wiring Diagram & Service Key

MODEL & SERIAL NUMBER LABEL AND

TECH SHEET LOCATION

1-4

STACKED WASHER/DRYER SPECIFICATIONS

MLE20PRA

369 lbs

W0

MLE/G20PDAY W0

180° Opening

Doors

US = 5,600 Watts / Canada = 5,250 Watts

Dryer Elec Element Rating

24,000 BTUs

Dryer Gas BTU Ratings

Variable Speed, Reversing /

Controlled Induction Motor / HP

230cfm / 215 cfm

Dryer Air Fow Gas/ Elec

AMPS

w/Electric Dryer 40

Canada Breaker Rating Amps

Stack w/Gas Dryer 15 Amps / w/Electric Dryer 15 &

Warm wash 1.6 gal (6.1liters)

Hot wash 3.4 gal (12.8 liters) /

oltage / Dryer Voltage

/ 6.7 ft

Capacity Washer/Dryer

asher with HE Dryer

Washer Power Cord Length

Washer 10

Amps / Gas Dryer 5 Amps / Elec Dryer 30 AMPS

MLE20PDA

STACKED W/D

75

Total Hot Water use/cycle*

Total water use/cycle*

(Owner

Adjustable)

Pedestal Equipped

& K nits, Q uick

Whites, Colors, Brights, Perm Press, Delicates

6 Cycles

Product Weight (uncrated)

Card Reader Not Included

Product Weight (crated)

2 mm)

(7

30.

(68.58 cm)

3.2 ft

Normal = 40 RPM

1-4

SPeCiFiCaTiOnS

Width

Front Load HE W

Model Number

Model Description

Color

White / Black Accents

Stainless Steel Trim

Washer Temperature Control

NTC - Thermister

Washer Sensors

Suds Sensor

NTC (Thermistor)

Water Level Sensor

W

ash Speed

Spin Speeds

Max = 1000 RPM

Medium = 850 RPM

Low = 750 RPM

Extra Low = 600 RPM

Rated Load Size

18 lbs

Washer V

Frequency

60 Hz

Max

Amp Draw

US Breaker Rating

Amps

6 ft

12.4 gallons/cycle*

1/4 HP

Height

Install Depth: Min - Max

28

.

75”

Money Acceptor

US = Single Coin Drop

Canada = Dual Coin Drop

27"

3

verage loads based on testing using* A

CSA Standard C360-03/DO E Appendix J1/

T396

MLE/G20PRAY

W0

ZW0

Z

3

Y

ES

30 AMPS

” (includes 1”

"leg height)

Stack w/Gas Dryer 20 Amps /

Washer 120 VAC / Gas Dryer 120 VAC / Elec Dryer

240 VAC

38 3 lbs

36 9 lbs

372 lbs

358 lbs

Elec

Gas Elec

Gas 369 lbs

358 lbs

Elec GasElec Gas

358 lbs

1-5

WARRANTY

MAYTAG

®

COMMERCIAL SINGLE-LOAD AND VENDED

MULTI-LOAD WASHER & DRYER

WARRANTY

LIMITED WARRANTY ON PARTS

For the rst ve years from the date of purchase, when this commercial appliance is installed, maintained and operated according to the

instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter “Maytag”) will pay for factory

specied parts or original equipment manufacturer parts to correct defects in materials or workmanship. Proof of original purchase date

is required to obtain service under this warranty.

ITEMS MAYTAG WILL NOT PAY FOR

1. All other costs including labor, transportation, or custom duties.

2. Service calls to correct the installation of your commercial appliance, to instruct you how to use your commercial appliance, to

replace or repair fuses, or to correct external wiring or plumbing.

3. Repairs when your commercial appliance is used for other than normal, commercial use.

4. Damage resulting from improper handling of product during delivery, theft, accident, alteration, misuse, abuse, re, ood, acts of

God, improper installation, installation not in accordance with local electrical or plumbing codes, or use of products not approved

by Maytag.

5. Pickup and Delivery. This commercial appliance is designed to be repaired on location.

6. Repairs to parts or systems resulting from unauthorized modications made to the commercial appliance.

7. The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in

accordance with published installation instructions.

8. Chemical damage is excluded from all warranty coverage.

9. Changes to the building, room, or location needed in order to make the commercial appliance operate correctly.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATIONS OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If you need service, please contact your authorized Maytag

®

Commercial Laundry distributor. To locate your authorized Maytag

®

Commercial Laundry distributor, or for web inquiries, visit www.MaytagCommercialLaundry.com.

3/10

For written correspondence:

Maytag

®

Commercial Laundry Service Department

2000 M-63 North

Benton Harbor, Michigan 49022 USA

10. Repairs made by a non-Whirlpool authorized service technician.

1-6

---- NOTES ----

2-1

INSTALLATION REQUIREMENTS

For complete installation instructions

See Links to documents page.

Tools and parts

Gather the required tools and parts before

starting installation. The parts supplied are in

the washer spin basket.

Tools needed for connecting water inlet hoses:

Pliers (that open to 1 9/16” [39.5 mm])

Flashlight (optional)

Tools needed for installation:

8” or 10” pipe wrench

8” or 10” adjustable wrench that opens to 1”

Flat blade screwdriver

Star blade screwdriver

T-20 security screwdriver

1” hex head socket or wrench

5/16” socket or wrench

Pliers that open to 1 9/16”

Level

Utility knife

1/4” nut driver

Locking pliers

Caulk gun and caulk (if installing new vent)

Vent clamps

Pipe-joint compound suitable for gas type

27” wood block

1/2” and 9/16” open-end wrenches

Ruler or measuring tape

Flashlight (optional)

•

A. U-shaped hose form

B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. Transit bolt hole plug (4)

E. Beaded tie strap

F. Drain hose

G. Hose clamp

Parts supplied:

D E G

A B

C

F

2-2

The installation may require additional parts.

If interested in purchasing any of the items

listed here, call toll-free

1-800 NO BELTS (1-800-662-3587).

Have Need to Buy

Laundry tub or

standpipe taller

than 96” (2.4 m)

Sump pump system (if not

already available)

Overhead sewer Standard 20 gal. (76 L),

39” (990 mm) tall drain tub

or utility sink and sump

pump (available from local

plumbing suppliers)

1” (25 mm)

standpipe

2” (51 mm) diameter to

1” (25 mm) diameter

Standpipe Adapter

Part Number 3363920,

Connector Kit

Part Number 285835

Drain hose too

short

Extension Drain Hose

Part Number 285863,

Connector Kit

Part Number 285835

Lint clogged

drain

Drain Protector

Part Number 367031

Connector Kit

Part Number 285835

Floor drain

system

Siphon break

Part Number 285834,

Connector Kit (x2)

Part Number 285835,

Extension Drain Hose

Part Number 285863

Water faucet

beyond reach of

ll hoses

2 longer water ll hoses:

6 ft (1.8 m) 90° bend hose

Part Number 76314,

10 ft (3.0 m) hose

Part Number 350008

ALTERNATE PARTS

Enhance the washer/dryer with these premium

accessories. For more high-quality items or to

order, call 1-800-901-2042,

or visit us at www.maytag.com/accessories.

In Canada call: 1-800-807-6777

or visit us at www.whirlpoolparts.ca.

Part # Accessory

8212526 Washer drip tray, ts under all

31682 All purpose appliance cleaner

1903WH Laundry supply storage cart

279818 3-way dryer venting kit

285834 Siphon break kit

Card Reader Conversion Kit For PD Models

Part # Card Reader Conversion Kit

W10439196

W10239515 Card Reader Harness

W10198323 Card Reader Bracket

W10198367 Card Reader Bezel

ACCESSORIES

2-3

DIMENSIONS

CLEARANCES

7

DIMENSIONS/CLEARANCES

Front View Side View Back View

1"

(25 mm)

74"

(1880 mm)

51"

(1295 mm)

29.5 "

(751 mm)

1

/2

27"

(686 mm)

1"

(25 mm)

74"

(1880 mm)

Dimensions

Clearances

Side Clearances Back/Top Clearances

0"

(0 mm)

0"

(0 mm)

2-4

STACKED WASHER/GAS DRYER

LOCATION REQUIREMENTS

Selecting the proper location for the washer/

dryer improves performance and minimizes

noise and possible washer “walk.”

The washer/dryer can be installed in a

basement, laundry room, or recessed area.

(See page 2-21) “Drain System.”

Companion appliance location requirements

should also be considered.

IMPORTANT: Do not install or store the

washer/dryer where it will be exposed to the

weather. Do not store or operate the washer/

dryer in temperatures at or below 32°F (0°C).

Some water can remain in the washer and can

cause damage in low temperatures. Proper

installation is your responsibility.

You will need:

A water heater set to deliver 120°F (49°C)

water to the washer.

A grounded electrical outlet located within

6 ft. (1.8 m) of where the power cord is

attached to the back of the washer. See

“Electrical Requirements.”

Hot and cold water faucets located within

4 ft. (1.2 m) of the hot and cold water fill

valves, and water pressure of 20–100 psi

(137.9–689.6 kPa).

A level floor with a maximum slope of 1” (25

mm) under entire washer/dryer. Installing

the washer/dryer on soft floor surfaces,

such as carpets or surfaces with foam

backing, is not recommended.

A sturdy and solid floor to support the

washer/dryer with a total weight (water and

load) of 450 lbs (204 kg).

A floor drain under the bulkhead.

Prefabricated bulkheads with electrical

outlets, water inlet lines, and drain facilities

should be used only where local codes

permit.

n

Explosion Hazard

Keep flammable materials and vapors, such as

petrol, away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion,

or fire.

WARNING

2-5

Recessed Area and Closet Installation

Instructions

This washer/dryer may be installed in a

recessed area or closet. For recessed area

and closet installations, minimum clearances

can be found on the warning label on the rear

of the dryer or in Dimensions and Clearances

(See page 2-3).

The installation spacing is in inches and is

the minimum allowable. Additional spacing

should be considered for ease of installation,

servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum

unobstructed air opening in the top and bottom

is required. Louvered doors with equivalent air

openings are acceptable.

The dryer must be exhausted outdoors.

Stacked Washer/Gas Dryer Installation

Clearances

The location must be large enough to allow

the washer and dryer doors to be fully

opened.

Additional spacing should be considered for

ease of installation and servicing. The doors

open more than 180°. The washer door is

not reversible.

Additional clearances might be required for

wall, door, and floor moldings.

Additional spacing of 1” (25 mm) on all

sides of the washer/dryer is recommended

to reduce noise transfer.

Companion appliance spacing should also

be considered.

When Installing A Gas Dryer:

IMPORTANT: Observe all governing codes

and ordinances.

Check code requirements: Some codes limit

or do not permit installation of clothes dryers

in garages, closets, or sleeping quarters.

Contact the local building inspector.

Make sure that lower edges of the cabinet,

plus the back and bottom sides of the

washer, are free of obstructions to permit

adequate clearance of air openings for

combustion air. See “Recessed Area and

Closet Installation Instructions” in the next

column for minimum spacing requirements.

n

24 in.

2

(155 cm

2

)

48 in.

2

(310 cm

2

)

3"

(76 mm)

3"

(76 mm)

Closet

door

Front

View

2-6

IMPORTANT: The washer/dryer must be

electrically grounded in accordance with local

codes and ordinances or, in the absence of

local codes, with the National Electrical Code,

ANSI/NFPA 70, latest edition, or Canadian

Electrical Code, CSA C22.1. If codes permit

and a separate ground wire is used, it is

recommended that a qualied electrical

installer determine that the ground path is

adequate.

A copy of the above code standards can be

obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

Do not ground to a gas pipe.

Do not have a fuse in the neutral or ground

circuit.

A 120 volt, 60 Hz, AC only, 15- or 20-

amp, fused electrical circuit is required. A

time-delay fuse or circuit breaker is also

recommended. It is recommended that a

separate circuit serving only this washer/

dryer be provided.

This washer/dryer is equipped with a power

supply cord having a 3 prong grounding

plug.

To minimize the possibility of shock, the

cord must be plugged into a mating, 3

prong, grounding-type outlet, grounded

in accordance with local codes and

ordinances. If a mating outlet is not

available, it is the personal responsibility

and obligation of the customer to have the

properly grounded outlet installed by a

qualified electrician.

If codes permit and a separate ground wire

is used, it is recommended that a qualified

electrician determine that the ground path is

adequate.

Check with a qualified electrician if not sure

that the washer/dryer is properly grounded.

n

STACKED WASHER/GAS DRYER

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can

result in death, fire, or electrical shock.

Page is loading ...

Maytag MLE20PDAYW0 User manual

This manual is also suitable for

Maytag MLE20PDAYW0 User manual

Related papers

Other documents