AAA Storage Sheds Glider Assembly Instructions

Brand: AAA Storage Sheds

Model: Glider

Type: Assembly Instructions

Tools needed:

•  Wrench

•  Wrench

• Rubber Mallet or Hammer

• #2 Square Drive Screwdriver

or Power Drill  Driver

Package Contents

NOTE: Do not tighten any bolts

until step 4 is completed.

1 - Seat (A)

2 - Base Crosspiece (G)

4 - Glider Bearing (O)

1 - Back (B) -

style may vary

1 - Le Arm (C) 1 - Right Arm (D)

1 - Right Base Leg (E) 1 - Le Base Leg (F)

Glider Assembly Instructions

Package contents continued on inside.

Step 7

Step 9

Step 8

Slide a washer (L) onto each bolt on the inside of

the leg.

Set the base into place. MAKE SURE YOU DON’T PUT

IT ON BACKWARDS. (See step 5, fig. A and fig. B.)

Now insert a

⁄16" bolt through the hole in the base,

this time with the threads pointing out (heads facing

in). Slide a washer (L) onto the bolt, and then attach

it to the glider bearing (O) with a lock nut (M). Repeat

on all four corners.

Now tighten ALL your bolts, and your glider is

complete. Enjoy!

Slide a glider bearing (O) onto each bolt. Make sure it

is turned the way it shows in the above picture. Now,

turn a lock nut (M) loosely on each bolt.

NOTE: Now make sure all the bolts have been tight-

ened before continuing to Step 9.

Step 1 Step 2

Lay seat (A) on a flat surface and slide back (B)

into seat as shown.

Tap bolts (H) into holes as shown with the heads

pointing toward the outside. Repeat on other end

and centers.

NOTE: Amount of centers may vary.

Step 3

Turn flange nuts (I) loosely onto the bolts.

NOTE: Do not tighten them until step 4 is completed.

Step 4

Step 6

Attach right arm (C) with two ¼" long bolts (J)

through legs, and one ¼" short bolt (H) through

arm and turn flange nuts (I) loosely onto the bolts.

Repeat on other end with le arm (D).

NOTE: You may have to push up or down, forward or

backward, on the back or arm assembly to line up

the bolt holes.

Turn the whole seat assembly upside down, and

insert a

⁄16" bolt (K) into each leg with the threads

pointing in toward center (heads facing out). Use a

rubber mallet and drive the square nibs of the bolt

firmly into the material to prevent the bolt from

spinning when you tighten the nut.

Step 5

To assemble the glider base, you have to attach

the base crosspieces (G) to the base legs (E) and (F)

using 1¾" screws (N)

NOTE the dierence in the front and the back of the

base as shown in figure (A) and figure (B) below.

See the dierence in the length of

fig. A and fig. B at the arrow.

Package Contents Continued from front page

Hardware Package

4 - ¼" Long Bolt (J)

10 - ¼" Short Bolt (H)

8 -

⁄16" Bolt (K)

12 - 1¾" Screw (N)

1 - Bit (P)

8 -

⁄16" Locknut (M)

8 -

⁄16"Washer (L)

14 - ¼" Flange Nut (I)

Short

Bolt (H)

Short

Bolt (H)

Long

Bolt (J)

Long

Bolt (J)

fig. A

Front Side

fig. B

Back Side

Step 1 Step 2

Lay seat (A) on a flat surface and slide back (B)

into seat as shown.

Tap bolts (H) into holes as shown with the heads

pointing toward the outside. Repeat on other end

and centers.

NOTE: Amount of centers may vary.

Step 3

Turn flange nuts (I) loosely onto the bolts.

NOTE: Do not tighten them until step 4 is completed.

Step 4

Step 6

Attach right arm (C) with two ¼" long bolts (J)

through legs, and one ¼" short bolt (H) through

arm and turn flange nuts (I) loosely onto the bolts.

Repeat on other end with le arm (D).

NOTE: You may have to push up or down, forward or

backward, on the back or arm assembly to line up

the bolt holes.

Turn the whole seat assembly upside down, and

insert a

⁄16" bolt (K) into each leg with the threads

pointing in toward center (heads facing out). Use a

rubber mallet and drive the square nibs of the bolt

firmly into the material to prevent the bolt from

spinning when you tighten the nut.

Step 5

To assemble the glider base, you have to attach

the base crosspieces (G) to the base legs (E) and (F)

using 1¾" screws (N)

NOTE the dierence in the front and the back of the

base as shown in figure (A) and figure (B) below.

See the dierence in the length of

fig. A and fig. B at the arrow.

Package Contents Continued from front page

Hardware Package

4 - ¼" Long Bolt (J)

10 - ¼" Short Bolt (H)

8 -

⁄16" Bolt (K)

12 - 1¾" Screw (N)

1 - Bit (P)

8 -

⁄16" Locknut (M)

8 -

⁄16"Washer (L)

14 - ¼" Flange Nut (I)

Short

Bolt (H)

Short

Bolt (H)

Long

Bolt (J)

Long

Bolt (J)

fig. A

Front Side

fig. B

Back Side

Tools needed:

•  Wrench

•  Wrench

• Rubber Mallet or Hammer

• #2 Square Drive Screwdriver

or Power Drill  Driver

Package Contents

NOTE: Do not tighten any bolts

until step 4 is completed.

1 - Seat (A)

2 - Base Crosspiece (G)

4 - Glider Bearing (O)

1 - Back (B) -

style may vary

1 - Le Arm (C) 1 - Right Arm (D)

1 - Right Base Leg (E) 1 - Le Base Leg (F)

Glider Assembly Instructions

Package contents continued on inside.

Step 7

Step 9

Step 8

Slide a washer (L) onto each bolt on the inside of

the leg.

Set the base into place. MAKE SURE YOU DON’T PUT

IT ON BACKWARDS. (See step 5, fig. A and fig. B.)

Now insert a

⁄16" bolt through the hole in the base,

this time with the threads pointing out (heads facing

in). Slide a washer (L) onto the bolt, and then attach

it to the glider bearing (O) with a lock nut (M). Repeat

on all four corners.

Now tighten ALL your bolts, and your glider is

complete. Enjoy!

Slide a glider bearing (O) onto each bolt. Make sure it

is turned the way it shows in the above picture. Now,

turn a lock nut (M) loosely on each bolt.

NOTE: Now make sure all the bolts have been tight-

ened before continuing to Step 9.

AAA Storage Sheds Glider Assembly Instructions

Brand: AAA Storage Sheds

Model: Glider

Type: Assembly Instructions

Download PDF

report

AAA Storage Sheds Glider Assembly Instructions

AAA Storage Sheds Glider Assembly Instructions

Other documents