EuroLite PAR-36 Spot short Operating instructions

Brand: EuroLite

Model: PAR-36 Spot short

Type: Operating instructions

This manual is also suitable for

PAR-36 SPOT

Page is loading ...

nicht ausgelegt ist. Beachten Sie auch unbedingt die Hinweise des Lampenherstellers. Bei Zuwiderhandlungen erlischt die Garantie. Setzen Sie nun die

Lampe ein. Klemmen Sie die Lampe mit dem Lampenklemmring fest. Schließen Sie die Lampe über die Kabelschuhe an die Netzleitung an. Schließen Sie

den Schutzleiter an die Schutzleiterschraube am Gehäuse an. Schließen Sie nun das Gerät wieder.

Schalten Sie das Gerät niemals ein, ohne vorher den

Gehäusedeckel geschlossen zu haben.

INSTALLATION

Achten Sie bei der Installation des Gerätes bitte darauf, daß sich im Abstand

von mind. 2 m keine leicht entflammbaren Materialien (Deko, etc.) befinden.

Befestigen Sie den Spot mit dem Bügel an Ihrem Traversensystem. Verwenden Sie aus Sicherheitsgründen ein Sicherheitsfangseil.

BEDIENUNG

Wenn Sie das Gerät an die Spannungsversorgung angeschlossen haben, steuern Sie die Spots über Ihr Lichtsteuergerät.

REINIGUNG UND WARTUNG

Die Lampe muß ausgewechselt werden, sobald sie beschädigt oder verformt ist.

Vor dem Wechseln der Lampe diese unbedingt erst abkühlen lassen und das Gerät allpolig von der Netzspannung trennen.

Sollten Sie noch weitere Fragen haben, steht Ihnen Ihr Fachhändler jederzeit gerne zur Verfügung.

OPERATING INSTRUCTIONS

3$56327

For your own safety, please read this user manual carefully before you initial start-up.

Every person involved with the installation, operation and maintenance of this device have to:

- be qualilfied

- follow the instructions of this manual

INTRODUCTION

Thank you for having chosen a PAR-36 SPOT. Unpack your PAR-36 SPOT.

Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the

device.

SAFETY INSTRUCTIONS

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary

for the user to follow the safety instructions and warning notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or

problems.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water

might damage your device. Leave the device switched off until it has reached room temperature.

Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Make sure

that the available voltage is not higher than stated on the rear panel. Make sure that the power-cord is never crimped or damaged by sharp edges. Check the

device and the power-cord from time to time. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-

cord by the plug. Never pull out the plug by tugging the power-cord.

During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective.

Never touch the device during the operation! The housing heats up to approx. 140° C.

Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty.

Keep away children and amateurs!

OPERATING DETERMINATIONS

This device is a spot designed for professional use on stages, in discotheques, etc. This fixture is only allowed to be operated with an alternating current of

max. 28 V/50-60 Hz. This device was designed for indoor use only. Do not shake the device. Avoid brute force when installing or operating the device.

You can install the device at any desired place in dry rooms. Please make sure that the device is not exposed to extreme heat, moisture or dust. There

should not be any cables lying around. You endanger your own and the safety of others! The minimum distance between light-output and the illuminated

surface must be more than 2 meters (Long) or 1 meter (Short

). Make sure that the area below the installation place is blocked when rigging, derigging or

servicing the fixture.

Always fix the fixture with an appropriate safety-rope. The maximum ambient temperature t

= 45° C must never be exceeded. The lamps need to be

preheated in order to protect them. Please adjust the filament preheat of your dimming pack so that the coiled filament glows slightly. Operate the device only

after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of

unprofessional operation! Please use the original packaging if the device is to be transported. Please consider that unauthorized modifications on the device

are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void.

Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, lamp explosion, crash etc.

CONNECTION WITH THE MAINS

In order to connect the device with the mains, a silicone power supply cable has to be installed. The voltage depends on the lamp being used, e.g. if a

28 V/250 W PAR-36 lamp is used, the device has to be connected with the mains via a 28-V-transformer.

This device falls under protection-class I. Therefore it is essential that the yellow/green conductor gets connected to earth.The electric connection must be

carried out by a qualified employee.

INSTALLAING/REPLACING OF THE LAMP

The lamp must only be installed by a qualified employee. For the PAR-36 Spot Long you can use PAR-36 lamps with up to max. 28 V/250 W. For the PAR-36

Spot Short you must only use PAR-36 lamps with up to max. 28 V/100 W. To install the lamps open the housing cover by pulling the extension spring.

Remove the fixation ring by pressing it together. Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device

was not designed for. Please follow the lamp manufacturer's notes! Damages caused by non-observance are not subject to warranty. Insert the lamp in the

housing. Fix the lamp with the fixation ring. Connect the lamp with the mains via the connection terminals. Connect the earthing with the earthing screw on the

housing. Close the device.

Do not operate this device with opened housing cover!

INSTALLATION

When installing the device, make sure there is no highly-inflammable

material (decoration articles, etc.) within a distance of min. 2 m.

Mount the spot with the mounting bracket to your trussing system. For safety reasons use an additional safety rope.

This device falls under protection-class I. Therefore it is essential that the yellow/green conductor gets connected to earth.The electric connection must be

carried out by a qualified employee.

OPERATION

After you connected the spot to the mains, you can control the spots via your lighting controller.

CLEANING AND MAINTENANCE

The lamp needs to be replaced as soon as it is damaged or warped.

Before replacing the lamp, unplug mains lead and let the lamp cool down.

Should you have further questions, please contact your dealer.

MODE D'EMPLOI

3$56327

Pour votre propre sécurité, veuillez lire ce mode d'emploi avec attention avant la première mise en service.

Toute personne ayant à faire avec le montage. la mise en marche. le maniement et l’entretien de cet appareil doit

- être suffisamment qualifiée

- suivre strictement les instructions de service suivantes.

INTRODUCTION

Nous vous remercions d'avoir choisi un PAR-36 SPOT. Sortez le PAR-36 SPOT de son emballage.

Avant tout, assurez vous que l'appareil n'a pas subi de dommages lors de son transport. Si tel était le cas, contactez immédiatement votre revendeur.

INSTRUCTIONS DE SÉCURITÉ

Cet appareil a quitté les ateliers dans un état irréprochable. Pour assurer un bon fonctionnement, sans danger, l'utilisateur doit suivre les instructions

contenues dans ce mode d'emploi.

Attention:

Tout dommage occasionné par la non observation des instructions de montage ou d'utilisation n'est pas couvert par la garantie.

Lorsque l'appareil est transporté d'un endroit froid à un endroit chaud, il se forme de la condensation susceptible d'endommager les modules électroniques.

Ne pas brancher l'appareil avant qu'il ait atteint la température ambiante.

Ne laissez pas les câbles d'alimentation en contact avec d'autres câbles. Soyez prudent; lorsque vous manipulez les câbles et les connexions, vous êtes

soumis à des risques d'électrocutions! Ne manipulez jamais les parties sous tension avec les mains mouillées!

Assurez-vous que la tension électrique ne soit pas supérieure à celle indiquée au dos de l’appareil. Mettez le câble d'alimentation seulement dans des prises

adaptées. Prenez garde de ne pas coincer ou abimer le câble d'alimentation. Contrôler l'appareil et les câbles d'alimentation régulièrement. Débranchez

l'appareil lorsque vous ne l'utilisez pas et avant de le nettoyer. Pour ce faire, utilisez les surfaces de maintien sur la fiche; ne tirez jamais sur le câble.

Lors de la première mise en service, il peut y avoir une émission de fumée et d'odeurs. Ceci n'est pas dû à un défaut de l'appareil.

Tout dommage résultant d'une modification sur l'appareil n'est pas couvert par la garantie.

Tenir les enfants et les novices éloignées de l'appareil.

Page is loading ...