Remington HC5600 Owner's manual

Page is loading ...

2

ENGLISH

Thank you for choosing Remington®. Our products are designed to meet the

highest standard of quality, functionality and design.

We hope you enjoy using your new Remington® product. Please read the

instructions for use carefully and keep in a safe place for future reference.

F IMPORTANT SAFETY INSTRUCTIONS

1 WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR

INJURY TO PERSONS:

2 This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been supervised/instructed and

understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be done by children unless they are

older than 8 and supervised.

3 Do not use this product if it is not working correctly, if it has been dropped or

damaged, or dropped in water.

4 Do not use accessories or attachments other than those we supply.

5 An appliance should never be left unattended when plugged in to a power

outlet, except when charging.

6 Keep the power plug and cord away from heated surfaces.

7 Make sure the power plug and cord do not get wet.

8 Do not plug or unplug the appliance with wet hands.

9 Do not use the product with a damaged cord. A replacement can be obtained

via our International Service Centres.

10 Do not twist or kink the cable, and don’t wrap it around the appliance.

11 Store the product at a temperature between 15°C and 35°C.

12 Do not immerse the appliance in liquid; do not use it near water in a

bath-tub, basin or other vessel; and don’t use it outdoors.

13 Suitable for cleaning under an open water tap.

3

ENGLISH

C KEY FEATURES

1 On / O Switch 6 Quick wash release button

2 Blade set 7 Charging indicator light

3 2 attachment guide combs (HC5400/HC5600)

3 -21mm and 24-42mm, 3mm adjustment 8 LED display (HC5800)

4 Adjustable stubble comb (HC5800) 9 Micro USB port

1-13mm, 2mm adjustment 10 Micro USB cable

5 1.5mm Stubble comb (HC5600) 11 Charging stand (HC5800)

12 Adaptor

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSLAE

HR

1

7

9

8

2

6

3

5

11

4

10

12

4

ENGLISH

C GETTING STARTED

, CHARGING YOUR APPLIANCE

• Beforeusingyourhairclipperforthersttime,chargefor16-20hours.

• Ensuretheproductisswitchedo.

• Connectthechargingadaptortotheproductandthentothemains.

• Iftheproductisnotgoingtobeusedforanextendedperiodtime(2–3

months), unplug it from the mains and store.

• Fullyrechargeyourproductwhenyouwouldliketouseitagain.

•

Allow 16 hours for a full charge on the HC5400 and 4.5 hours on the HC5600 and

HC5800.

• Topreservethelifeofyourbatteries,letthemrunoutevery6monthsthen

recharge for 16-20 hours.

O This appliance should be charged by approved safety isolating adaptors

PA-3215E (for HC5400 EU version) or PA-3215U (for HC5400 UK version) with the

output capacity of 3.2V dc; 1500mA; and should be charged by approved safety

isolating adaptors

PA-4515E (for HC5600, HC5800 EU version) or PA-4515U (for HC5600,HC5800 UK

version) with the output capacity of 4.5V dc; 1500mA .

, QUICK CHARGE (HC5600 & HC5800)

Quick charge

time

10 minutes 30 minutes 1 hour 2 hours

Run time 5 minutes 15 minutes 30 minutes 40 minutes

, CHARGING VIA CHARGING STAND (HC5800)

• Ensuretheproductisswitchedo.

• Connectthechargingadaptortothechargingstandandthentothemains.

• Allow4.5hoursforafullcharge.

, CHARGING VIA STANDARD ELECTRICAL SOCKET

• Ensuretheproductisswitchedo.

• Connectthechargingadaptortotheproductandthentothemains.

•

Allow 16 hours for a full charge on the HC5400 and 4.5 hours on the HC5600 and

HC5800

.

5

ENGLISH

, USB

• ConnectyourUSBcabletotheUSBportonyourpowersource.

• ConnecttheUSBcabletoyourappliance.

Note: charging may take longer when charging via USB.

, CORDED USE

• Connectthechargingadaptortotheproductthentothemains.

• Whenthecordisconnectedtothemains,adigitaldisplaywillbedisplayedon

the appliance (HC5800).

FCAUTION: Extended mains only use will result in the reduction of the battery

life.

F WARNING: The appliance can not be operated in corded mode while

connected to a PC via the USB port.

, CORDLESS USE

Whentheunitisswitchedonandfullycharged,theproductcanbeusedin

cordless mode for up to 60 minutes for the HC5400 and up to 120 minutes for the

HC5600 & HC5800.

F INSTRUCTIONS FOR USE

, BEFORE STARTING THE CUT

• Inspecttheclippermakingsurethatitisfreefromhairanddirt.

• Seatthepersonsothattheirheadisapproximatelyatyoureyelevel.

• Beforecutting,alwayscombthehairsoitistanglefreeanddry.

Comb position Adjustable

stubble comb

(HC5800)

Short comb Long comb

1 1mm 3mm 24mm

2 3mm 6mm 27mm

3 5mm 9mm 30mm

4 7mm 12mm 33mm

5 9mm 15mm 36mm

6 11mm 18mm 39mm

7 13mm 21mm 42mm

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSLAE

HR

6

, TO ATTACH A COMB

• Holdthecombwithitsteethupward.

• Slideitontoandalongtheclipperbladeuntilthefrontofthecombrmlysits

against the clipper blade.

, TO REMOVE THE COMB

• Holdingtheclipperwiththebladesfacingawayfromyou,rmlypushthecomb

upward and away from the blades.

, INSTRUCTIONS FOR CUTTING HAIR

For even cutting, allow the comb attachment/blade to cut its way through

 thehair.Donotforceitthroughquickly.Ifyouarecuttingforthersttime,start

with the maximum comb attachment.

, STEP 1 – Nape of the neck

• Setthecombto3mmor6mm.

• Holdtheclipperwiththebladeteethpointingupwards.Beginstartingatthe

centre of the head at the base of the neck.

• Slowlylifttheclipper,workingupwardsandoutwardsthroughthehair,

trimming just a little at a time.

, STEP 2 – Back of the head

• Withthecombsetat12mmor18mm,cutthehairatthebackofthehead.

, STEP 3 – Side of the head

• Setthecombto3mmor6mm,trimsideburns.Thenchangethesettingto9mm

and continue to cut the top of the head.

, STEP 4 – Top of the head

• Usethelongerlengthcombattachmentandsetitto24mmor27mmthencut

hair on top of the head against the direction in which the hair normally grows.

• Forlongerhairontop,usethelongerlengthcombattachment(24–42mm)to

achieve the desired style.

• Alwaysworkfromthebackofthehead.

, STEP 5 – The nishing touches

• Usetheclipperwithoutanattachmentcombforclosetrimmingaroundthe

base and sides of the neck.

• Toproduceacleanstraightlineatthesideburns,reversethehairclipper.Place

the reversed clipper at right angles to the head, tips of the blades lightly

touching the skin and then work downwards.

ENGLISH

7

, SHORT TAPERED STYLES – “FLAT TOPS” & SHORT CUTS

• Startingwiththelongestguidecombattached(24-42mm),cutfromtheback

of the neck to the crown. Hold the guide comb at against the head and slowly

move the clipper through the hair.

• Usethesameprocedurefromthelowersidetotheuppersideofthehead.

Then cut the hair against the direction in which it grows and level with the

sides.

• Togivea“attop”look,thehairontopoftheheadmustbecutoverthetopof

a at comb.

• Useacloserguidecombtotaperthehairdowntothenecklineasdesired.

, DUAL BOOST SYSTEM (HC5600)

• Thereare3settingsfortheDualBoostsystem:O,On,Boost.

• Iftheclipperissettoon,itwillrunatregularpower.

• Iftheclipperissettoboost,itwillprovidemaximumpower.

, AUTO BOOST SYSTEM (HC5800)

• Thereare3settingsfortheAutoBoostsystem:O,Auto,Boost

• IftheClipperissettoAuto,itwillrunatregularpowerunderlowload 

conditions.

• Whenmorepowerisneeded,theclipperwillautomaticallysensethisand

provide maximum boost.

• ToactivatetheBoostsetting,depressthepowerbuttonfor2seconds.The

clipper will then constantly run at maximum power.

C CARE FOR YOUR HAIRCLIPPER

Yourclipperisttedwithhighqualityblades.Toensurelonglastingperformance

of your clipper, clean the blades and unit regularly. Always keep the attachment

guide comb on the trimmer blade.

, AFTER EACH USE

• Ensuretheclipperisswitchedoanddisconnectedfromthemainsbefore

cleaning.

• Brushtheaccumulatedhairfromtheblades.Donotsubmergetheclipperin

water.

• Tocleanunit,wipewithdampclothanddryimmediately.

, WASHABLE CLEANING

• TheQUICKWASHSYSTEMisdesignedtomaximisetheeciencyofwashable

cleaning.

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSLAE

HR

8

• Pushthebuttonthatislocatedonthefrontofthehairclipper.Thebladeswill

slide out and the blade set can be easily cleaned under the tap.

• Oncethebladesarecleanedthebladesarelockedintoplacebypushingthe

blade set towards the hair clipper head and will snap into place.

• Donotruntheentireunitunderthetap,onlythebladesetismeanttobe

submerged in water.

Note: Ensure the clipper is turned o when cleaning.

, EVERY SIX MONTHS

• Atregularintervalsthebladesetshouldberemovedandcleaned.

• Removethe2screwsretainingthexedbladewithascrewdriver.Donot

remove blade set.

• Brushouthairsfrombetweenthebladeswithsoftcleaningbrush.Donot

remove the lubricating grease from the blades. It is not necessary to remove the

small moving blade from the unit.

• Ifthemovingbladehasbeenremovedthiscanbere-ttedbyslottingthe

coated blade holder over the pin in the centre of the interior product head. The

groove on the coated blade, just below the teeth, rests on a metal plate at the

 oppositesidetothescrewholes.Thexedbladeisttedwiththeraisedprole

 pointingoutwardsandxedwiththe2screws.

• Notethatifthebladesarenotcorrectlyalignedthencuttingeciencywillbe

impaired.

• Placeafewdropsofcutterorsewingmachineoilontotheblades.Wipeo

excess oil.

, CLEANING CAUTIONS

• Ensuretheapplianceisswitchedoandunplugfromthemainoutletbefore

cleaning.

• Onlytheattachmentguidecombsandtrimmerblademayberemovedfrom

the product for cleaning.

• Cleaningshouldbedonewithasoftbrush,suchasthebrushsuppliedwiththe

product.

• Donotrinseunderwater.

• Donotuseharshorcorrosivecleanersontheunitsortheirblades.

ENGLISH

9

BATTERY REMOVAL

• Thebatterymustberemovedfromtheappliancebeforeitisscrapped.

• Theappliancemustbedisconnectedfromthesupplymainswhenremoving

the battery.

• Ensurethattheclipperisdischargedofallpoweranddisconnectedfromthe

mains.

• Removethescrewcoverfrombackhousing.

• Usingasmallscrewdriver,remove(1)screwfromthebottomoftheclipper.

• Prythefrontpanelfromthefronthousingandexposetheinnerhousing.

• Usingasmallscrewdriver,remove(4)screwsfrominnerhousing

• PrythecoverofinnerhousingandexposethePCBandbatteries.

• Cutorbreakthewirestampsonthebothendofthebatteriesandremovethe

batteries.

• Thebatteryistobedisposedofsafely.

H ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous

substances in electrical and electronic goods, appliances marked with

this symbol must not be disposed of with unsorted municipal waste, but

recovered, reused or recycled.

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSLAE

HR

Page is loading ...

168

Model No HC5400/HC5600/HC5800

Taşıma ve nakliye sırasında dikkat edilecek hususlar :

- Ürünü düşürmeyiniz

- Darbelere maruz kalmamasını sağlayınız

- Cihazı nakliye sırasında orijinal ambalajında taşıyınız.

Bakanlıkça tespit ve ilan edilen kullanım ömrü 7 yıldır.

ÜRETİCİ FİRMA BİLGİSİ: VARTA Consumer Batteries GmbH & Co. KGaA, Alfred-Krupp-Str. 9,

73479 Ellwangen, Germany.

Производитель: Spectrum Brands Shenzhen Ltd./Спектрум Брэндс

Шеньчжень

Лтд., Китай для Varta Consumer Batteries GmbH & Co. KGaA, Альфред-

Крупп Штрассе 9, Элльванген, 73479, Германия

Изделие использовать по назначению в соответствии с инструкцией по

эксплуатации

13/INT/ HC5400/5600/5800 T22-0001004 Version 04 /13

Remington® is a Registered Trade Mark of Spectrum Brands,Inc.,

or one of its subsidiaries

VARTA Consumer Batteries GmbH & Co. KGaA, Alfred-Krupp-Str. 9, 73479 Ellwangen,

Germany

www.remington-europe.com

Remington HC5600 Owner's manual

Remington HC5600 Owner's manual

in other languages

Related papers

Other documents