Graco 332223B Owner's manual

Brand: Graco

Model: 332223B

Type: Owner's manual

This manual is also suitable for

332223B - Retro-Fit Kit for LL250 and LL200 Pressurized Bead Systems

Graco 332223B - Retro-Fit Kit for LL250 and LL200 Pressurized Bead Systems enables the user to upgrade their existing LL250 or LL200 stripers to pressurized bead systems. With the new system, the user will benefit from improved striping performance and reduced maintenance requirements. The kit includes all the necessary components, such as a new fan pulley, gun arm bracket, and cable stud, to perform the upgrade. Detailed instructions with illustrations are provided to guide the user through the installation process.

332223B

Kit Instructions

Retro-Fit Kit for LL250 and LL200 Pressurized

Bead Systems Built BEFORE January 1, 2013

For professional use only.

Model 16U272

Important Safety Instructions

Read all warnings and instructions in the

striper manual. Save these instructions.

ti20896a

Ref. Part Description Qty.

1 15F213 BRACKET, cable 2

2 16U904 TOOL, drill bit, no. 15 1

3 16U205 PULLEY, fan, with attachment holes 1

4 120087 SCREW, set, 1/4 in. x 1/2 in. 2

5 260387 SCREW, pan hd, X recess 4

6 116876 WASHER, flat 4

7 116969 NUT, lock 4

8 24M638 BAR, gun holder, LL IV 250 SPS 2

9 101690 TOOL, allen wrench 1

10 100633 TOOL, allen wrench 1

11 15F211 STUD, cable 2

12 16U913 TOOL, torx bit, T-20 1

Tools Needed:

2 332223B

Tools Needed:

• 1/8 in. Allen Wrench

• 7/64 in. Allen Wrench

• 3/8 in. Wrench

• 7/16 in. Wrench

• 9/16 in. Wrench

• .180 in. Drill Bit

• T-20 Torx Bit

• Phillips Screwdriver

• Power DRill

•Pliers

•Marker

Instructions for LL250 Units

332223B 3

Instructions for LL250 Units

Fan Belt Removal

1. Turn off unit. Relieve pressure in paint striper and

remove paint hopper.

2. Locate belt shroud (A). Use 3/8 in. wrench to loosen

or remove four screws and remove shroud.

3. Before loosening belt assembly, mark location of

hydraulic reservoir against stationary base.

4. Use 9/16 in. wrench to loosen (but do not remove)

four bolts (B) that secure hydraulic reservoir system

to base plate.

5. Loosen two belt tensioning bolts (C) to take tension

off of belt. Loosen only until belt can be removed.

6. Remove belt (D) from fan pulley (E).

Replace Pulley

1. Remove original pulley and replace with new pulley.

Use 1/8 in Allen wrench to tighten two set screws.

NOTE: Make sure key is in place before installing

new pulley.

2. Align new fan pulley (E) with engine pulley.

ti19128a

ti20529a

ti19147a

ti19146a

ti20885a

ti20526a

ti20528a

Instructions for LL250 Units

4 332223B

3. Use 1/8 in. Allen wrench to tighten two set screws to

secure pulley onto shaft. Torque to 58 to 62 in-lb

(6.6 to 7.0 N•m).

4. Route belt (D) over new pulley.

5. Tighten two tensioning bolts (C) until hydraulic res-

ervoir is in its original location noted by marker line.

6. Tighten four reservoir bolts.

Remove Original Fan Grill and

Rivets

1. Remove belt shroud removed from unit.

2. Use .180 diameter drill bit (supplied) to drill-out

rivets from back side of shroud.

3. Once ridge has been drilled away on rivet, the

remaining portion can be pushed through hole.

NOTE: The pressurized bead system comes with a

new fan grill with open center. Leave belt shroud off

for installment of pressurized bead system. Replace

with grill from pressurized bead kit.

ti20527a

ti20885a

ti19150a

ti19151a

ti20524a

ti20520a

Instructions for LL250 Units

332223B 5

Install New Gun Arm Bracket

1. Remove clip (F) from cable eyelet (G).

2. Pinch retaining teeth (H) in and pull actuation cable

(J) out of bracket.

3. Replace original gun arm assembly with new gun

arm assembly.

4. Push bracket (X) all the way forward in slots.

5. Use 5/32 in. Allen wrench to tighten two head

screws (K).

6. Reinstall cable and clip.

ti20522a

ti20523a

ti20716a

ti21406a

ti20217a

Instructions for LL200 Units

6 332223B

Instructions for LL200 Units

Fan Belt Removal

1. Turn off unit. Relieve pressure in paint striper and

remove paint hopper.

2. Loosen knob and rotate belt shroud out of way.

3. Rotate engine upward and remove belt (D) from fan

pulley (E).

Replace Pulley

1. Remove original pulley and replace with new pulley.

Use 1/8 in Allen wrench to tighten two set screws.

NOTE: Make sure key is in place before installing

new pulley.

2. Align new fan pulley (E) with engine pulley.

3. Use 1/8 in. Allen wrench to tighten two set screws to

secure pulley onto shaft. Torque to 58 to 62 lb-in

(6.6 to 7.0 N•m).

4. Route belt (D) over new pulley (E).

Remove Original Fan Grill

1. Use star bit (supplied) to remove four screws (L)

from shroud. Remove original fan grill (M).

2. NOTE: The pressurized bead system comes with a

new fan grill with open center. Leave belt shroud off

for installment of pressurized bead system. Replace

with grill from PBS kit.

3. Close belt shroud with new fan grill onto unit.

NOTE: You may need to flex shroud around

extended shaft on the fan pulley.

ti20712a

ti20526a

ti20528a

ti20527a

ti20885a

ti20713a

ti20714a

ti21196a

Instructions for LL200 Units

332223B 7

Install New Gun Arm Bracket

1. Remove trigger cable (N) on old gun.

2. Remove old gun arm.

3. Loosen allen heads (P) and remove LL250 bracket

(R).

4. Replace with LL200 bracket (S). Push all the way

forward in slots and tighten Allen heads (P).

5. Replace the LL250-style cable stud with LL200-style

cable stud.

6. Replace old gun bracket with new bracket

assembly (T).

NOTE: See installation manual 332230 for additional

information.

7. Reinstall cable.

ti20886a

ti20887a

ti20718a

ti20719a

ti21323a

ti21322a

LL250-Style LL200-Style

ti20710a

ti21325a

ti21324a

GH200

250SPS

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 332223

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

www.graco.com

Revision B - October 2013

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in

material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty

published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written

recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty

installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of

non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with

structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or

maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of

the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned

to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will

be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or

consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to

the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these

warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or

the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the

negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,

given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la

rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite

de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

Graco 332223B Owner's manual

Brand: Graco

Model: 332223B

Type: Owner's manual

This manual is also suitable for

332223B - Retro-Fit Kit for LL250 and LL200 Pressurized Bead Systems

Download PDF

report

Graco 332223B Owner's manual

This manual is also suitable for

Graco 332223B Owner's manual

Related papers

Other documents