Frigidaire FPEC3677RF Installation guide

1

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

A

F

B

C

D

E

All dimensions are in inches (cm).

Only some models are available in Canada.

*

Allow 2" (5 cm) space below cooktop to clear the electric cable and allow for installation of the

junction box on the wall at the back of the cooktop.

P/N 318205403 (0904) Rev. C

English – pages 1-8

Español – pages 9-16

Français – pages 17-24

Cooktop Dimensions

IMPORTANT INSTALLATION‑INFORMATION

• Allelectriccooktopsrunoffasinglephase,three-wire

orfour-wirecable,240/208volt,60hertz,AConly

electrical supply with ground.

• Pleasenoteminimumdistancesbetweencooktopand

adjacent and overhead cabinetry is 30" (76.2cm).

* 30" (76.2 cm) min. for unprotected cabinet

24" (61 cm) min. for protected surface

Cooktop Cutout Dimensions

Figure 1

30" Min. *

(76.2 cm)

Printed in China

MODEL A. LENGTH B. WIDTH C. DEPTH

CUTOUT DIMENSIONS

F. DEPTH

BELOW

COOKTOP*

D. LENGTH E. WIDTH

MIN. MAX. MIN. MAX.

26" Coil Elements 25¾ (65.4) 21

9

/

16

(54.8) 3½ (8.9) 25 (63.5) 25 (63.5) 20½ (52.1) 20½ (52.1) 5½ (14)

30" Ceramic Glass 30

3

/

8

(77.8) 21

3

/

8

(54.4) 2

5

/

8

(6.7) 29

5

/

8

(75.2) 29

7

/

8

(75.9) 20¼ (51.4) 20½ (52.1) 5 (12.7)

30" Coil Elements 30 (76.2) 21½ (54.6) 3 (7.6) 26¾ (67.9) 28¼ (71.8) 19

1

/

8

(48.6) 20 (50.8) 5 (12.7)

32" Ceramic Glass 32¼ (81.9) 20¼ (51.4) 3¾ (9.5) 31 (78.7) 31¼ (79.4) 19 (48.3) 19¼ (48.9) 5¾ (14.6)

24 (61.0) 23 (58.5) 23¼ (59.0)

36" Ceramic Glass 36¾ (93.5) 21

3

/

8

(54.4) 2

5

/

8

(6.7) 35

5

/

8

(90.5) 36

1

/

8

(91.8) 20¼ (51.4) 20½ (52.1) 5 (12.7)

36" Coil Elements

(36" X 18")

36 (91.4) 18 (45.7) 3

7

/

8

(9.8) 34¼ (87) 34

3

/

8

(87.3) 16

5

/

8

(42.2) 16¾ (42.5) 5

7

/

8

(14.9)

36" Coil Elements

(36" x 21½")

36 (91.4) 21½ (54.6) 3 (7.6) 32¾ (83.2) 34¼ (87) 19 (48.3) 20 (50.8) 5 (12.7)

INSTALLATION AND SERVICE MUST BE PERFORMED

BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING

FOR YOUR SAFETY: Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of this or any other appliance.

Canada United States

32" Coil Elements 32¼ (81.9) 20¼ (51.4) 3¾ (9.5) 31 (78.7) 31¼ (79.4) 19 (48.3) 19¼ (48.9) 5¾ (14.6)

24" Ceramic Glass

21

3

/

8

(54.4)

2

5

/

8

(6.7) 20¼ (51.4) 20½ (52.1) 5 (12.7)

2

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

F

E

D

A

Figure 2 – COUNTERTOP CUTOUT OPENING

CAUTION

To eliminate the risk of burns or

rebyreachingoverheatedsurfaces,cabinet

storage space located above the cooktop should

beavoided.Ifcabinetstorageisprovided,risk

can be reduced by installing a range hood that

projectshorizontallyaminimumof5"(12.7cm)

beyond the bottom of the cabinets.

Overhead Cabinet Should Not Exceed a

Maximum Depth of 13" (33 cm)

30" (76.2 cm) Min. Clearance

Between the Top of the

Cooking Platform and the

Bottom of an Unprotected

Wood or Metal Cabinet

24" (61 cm) Min. when

Bottom of Wood or Metal

Cabinet is Protected by

Not Less Than 1/8" Flame

Retardant Millboard Covered

With Not Less Than No. 28

MGSSheetSteel,0.015"(0.4

mm)StainlessSteel,0.024"

(0.6 mm) Aluminum or

0.020" (0.5 mm) Copper

2 1/2" (6.4 cm)

Min. From Edge

of Cutout to Front

Edge of Countertop

Approximate Location of

Junction Box

18"

(45.7 cm)

* Letters on this ﬁgure refer to chart on

front page except for G, H and J.

H

Min. From Edge of

Cooktop to Nearest

Combustible Wall (Either

Side of Unit).

MODEL G H J

26" Coil Elements

3½" (8.9 cm)

3" (7.6 cm)

2" (5.1 cm)

30" Ceramic-Glass

4" (10.2 cm)

7½" (19.1 cm)

2" (5.1 cm)

30" Coil Elements

6" (15.2 cm)

7½" (19.1 cm)

2¼" (5.7 cm)

32" Ceramic-Glass

4" (10.2 cm)

7½" (19.1 cm)

2" (5.1 cm)

32" Coil Elements

6" (15.2 cm)

7½" (19.1 cm)

2¼" (5.7 cm)

36" Ceramic-Glass

4" (10.2 cm)

7½" (19.1 cm)

2" (5.1 cm)

36" Coil Elements

6" (15.2 cm)

3" (7.6 cm)

(36" X 18")

36" Coil Elements

6" (15.2 cm)

7½" (19.1 cm)

2¼" (5.7 cm)

(36" X 21½")

25" Min.

(63.5 cm Min.)

12"

(30.5 cm)

10"

( 25.4 cm)

Min.

J Min. Recommended

Distance Between Rear

Edge of Cutout and

Nearest Combustible

Surface Above

Countertop

Important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions with your owner's guide for future

reference.

For a drawer installation below the

cooktop,allowDimensionG of clearance

underneath the countertop. The drawer

must not interfere with the electrical

installation of the cooktop or contain

ﬂammable materials.

24" Ceramic-Glass

4" (10.2 cm) 7½" (19.1 cm) 2" (5.1 cm)

3

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

2. The ﬂexible armored cable extending from the

appliance should be connected directly to the

junction box. The junction box should be located

as shown in Figure 1 or Figure 2 and with as much

slack as possible remaining in the cable between

theboxandtheappliance,soitcanbemovedif

servicing is ever necessary.

3. A suitable strain relief must be provided to attach

the ﬂexible armored cable to the junction box.

Unpacking Instructions

(Models with Ceramic-Glass Smoothtop Only)

1. Leave corner supports on cooktop until completion

of Electrical Connection.

2. Be sure the bottle of cleaner conditioner packed

in the literature bag is left where the user can

ﬁnd it easily. It is important that the ceramic-glass

smoothtop be pretreated before use.

IMPORTANT SAFETY

INSTRUCTIONS

• Be sure your cooktop is installed and grounded

properly by a qualiﬁed installer or service

technician.

•These cooktops must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA No.

70—latest edition in the United States, or with

CSA Standard C22.1, Canadian Electrical Code, Part

1, in Canada.

WARNING

The electrical power to the cooktop

must be shut off while line connections are being

made. Failure to do so could result in serious injury

or death.

Provide Electrical Connection

Install the junction box under the cabinet and run

120/240or120/208Volt,ACwirefromthemaincircuit

panel. DO NOT connect the wire to the circuit panel at

this time.

Electrical Requirements

This appliance must be supplied with the proper voltage

andfrequency,andconnectedtoanindividual,properly

groundedbranchcircuit,protectedbyacircuitbreaker

or fuse. A circuit breaker or fuse is required by your

appliance. The circuit breaker or fuse amperage

recommended for your appliance is 40A or 50A.

Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208

Volt,60HzAConlyelectricalsupplyisrequiredona

separate circuit fused on both sides of the line (red

and black wires). A time-delay fuse or circuit breaker is

recommended. DO NOT fuse neutral (white wire). Only

certain cooktop models may be installed over certain

built-in electric oven models. Approved cooktops and

built-in ovens are listed by the MFG ID number (see the

insert sheet included in the literature package).

NOTE:Wiresizesandconnectionsmustconformwith

thefusesizeandratingoftheapplianceinaccordance

with the American National Electrical Code ANSI/NFPA

No.70-latestedition,orwithCanadianCSAStandard

C22.1,CanadianElectricalCode,Part1,andlocalcodes

and ordinances.

An extension cord should not be used

with this appliance. Such use may result in a ﬁre,

electrical shock, or other personal injury.

Figure 3

Serial plate

(under cooktop)

Electrical Connection

It is the responsibility and obligation of the consumer to

contact a qualiﬁed installer to assure that the electrical

installation is adequate and is in conformance with the

NationalElectricalCodeANSI/NFPANo.70-latestedition,

orwithCSAStandardC22.1,CanadianElectricalCode,

Part1,andlocalcodesandordinances.

Risk of electrical shock (Failure to

heed this warning may result in electrocution or

other serious injury.) This appliance is equipped

with copper lead wire. If connection is made to

aluminum house wiring, use only connectors that

are approved for joining copper and aluminum wire

in accordance with the National Electrical Code

and local code and ordinances. When installing

connectors having screws which bear directly on

the steel and/or aluminum ﬂexible conduit, do no

tighten screws sufﬁciently to damage the ﬂexible

conduit. Do not over bend or excessively distort

ﬂexible conduit to avoid separation of convolutions

en exposure of internal wires.

Electrical ground is required on this appliance.

4

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

Figure 5 – U.S.A. Only

3‑WIRE GROUNDED JUNCTION BOX

Cable from Power Supply

Black

Wires

Junction

Box

Cable from appliance

Ground Wire

(Bare or Green Wire)

Ground Wire

White Wire

Red Wires

U.L.-Listed Conduit

Connector (or CSA listed)

Figure 4 – U.S.A. Only

3‑WIRE GROUNDED JUNCTION BOX

Cable from Power Supply

Black

Wires

Junction Box

Cable from appliance

Ground Wire

(Bare or

Green Wire)

Ground Wire

Red

Wires

U.L.-Listed Conduit

Connector (or CSA

listed)

This appliance is manufactured with a frame connected

green (or bare copper) ground wire.

DO NOT ground to a gas supply pipe.

DO NOT connect to electrical power supply until

appliance is permanently grounded. Connect the

ground wire before turning on the power.

If your appliance is not equipped with a white

neutral conductor:

Connectonlytoa3-wire,120/240Vpowersupply;the

neutral conductor is not required for the operation of the

appliance. The potential at the power supply electrical

connections shall be 150V to ground or less.

NOTE TO ELECTRICIAN: The armored cable leads

suppliedwiththeapplianceareUL-recognizedfor

connection to larger gauge household wiring. The

insulation of the leads is rated at temperatures much

higher than temperature rating of household wiring. The

current carrying capacity of the conductor is governed by

thetemperatureratingoftheinsulationaroundthewire,

rather than the wire gauge alone.

RISK OF ELECTRIC SHOCK: Grounding through the

neutral conductor is prohibited for new branch-circuit

installations(1996NEC);mobilehomes;recreational

vehicules;orinCanada,orinanareawherelocalcodes

prohibit grounding through the neutral connector.

(If your appliance is equipped with a

white neutral conductor.)

This appliance is manufactured with a white neutral

power supply and a frame connected copper

wire. The frame is grounded by connection of

grounding lead to neutral lead at the termination

of the conduit, if used in USA, in a new branch

circuit installation (1996 NEC), mobile home,

recreational vehicles, where local code do not

permit grounding trough the neutral (white) wire

or in Canada, disconnect the white and green lead

from each other and use ground lead to ground

unit in accordance with local codes, connect neutral

lead to branch circuit‑neutral conductor in usual

manner see Figure 6 or 7. If your appliance is to

be connected to a 3 wire grounded junction box

(US only), where local code permit connecting

the appliance‑grounding conductor to the neutral

(white) see Figure 4 or 5.

Where local codes permit connecting the

appliance‑grounding conductor to the neutral

(white) wire (USA only):

Your appliance has a 3‑wire cable to be connected

to a 3‑wire grounded junction box (see ﬁgure 4):

1. Disconnect the power supply.

2. Inthecircuitbreaker,fuseboxorjunctionbox:

Connect appliance and power supply cable wires as

shown in ﬁgure 4.

Your appliance has a 4‑wire cable to be connected

to a 3‑wire grounded junction box (see ﬁgure 5):

1. Disconnect the power supply.

2. Inthejunctionbox:

Connect appliance and power supply cable wires as

shown in Figure 5.

5

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

Figure 7

4‑WIRE GROUNDED JUNCTION BOX

Cable from Power Supply

White

Wires

Junction Box

Cable from appliance

Ground Wire

(Bare or

Green Wire)

Ground

Wire

Black

Wires

Red

Wires

U.L.-Listed Conduit

Connector (or CSA listed)

If the appliance is used in a new branch

circuit installation (1996 NEC), mobile home,

recreational vehicle, or where local codes DO

NOT permit grounding through the neutral

(white) wire, the appliance frame MUST NOT

be connected to the neutral wire of the 4‑wire

electrical system.

Your appliance has a 3‑wire cable to be connected

to a 4‑wire grounded junction box (see ﬁgure 6):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white

appliance cable wires.

3. Cap the white wire from the power supply cable if a

3-wire appliance cable is supplied.

4.Inthecircuitbreaker,fuseboxorjunctionbox:

Connect appliance and power supply cable wires as

shown in ﬁgure 6.

Figure 6

4‑WIRE GROUNDED JUNCTION BOX

Cable from Power Supply

Black

Wires

White Wire

Junction Box

U.L.-Listed

Conduit

Connector (or

CSA listed)

Cable from appliance

Red

Wires

Ground Wire

(Bare or

Green Wire)

Ground Wire

Your appliance has a 4‑wire cable to be connected

to a 4‑wire grounded junction box (see ﬁgure 7):

1. Disconnect the power supply.

2. Inthejunctionbox:

Connect appliance and power supply cable wires as

shown in Figure 7.

6

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

Cooktop Installation

1. All Ceramic‑Glass Cooktops

Visually inspect the cooktop for damage. Also make sure

all cooktop screws are tight (see Figure 8).

Set the cooktop into the countertop cutout.

NOTE:Donotusecaulkingcompound;cooktopshould

be removable for service when needed.

WARNING

Do not remove the built in springs on

the edges of the cooktop. These springs center the

cooktop in the space provided. The cooktop must

be centered to prevent excess heat buildup that

may result in heat damage or ﬁre (see Figure 9).

Screws

Figure 8

The retainer brackets MUST be installed, to meet

local codes or, in their absence, with the National

Electrical Code ANSI/NFPA No. 70—latest edition, or

with CSA Standard C22.1, Canadian Electrical Code,

Part 1 (see Figure 10).

Figure 9

8 Built-in

Springs

2 Retainer

Brackets

Position brackets on

unit cutout center

line (CL)

Cooktop

Retainer Brackets Must

Be Installed At Least

1/16" (0.16 cm)

BELOW Countertop

Built in

Spring

Countertop

Retainer

Bracket

Figure 10

2. Models: 26" and 36" (36" X 18") Coil Elements

Cooktops

Set the cooktop into the countertop cutout. Lift the

cooktop and fasten the ends of the box to the counter

with wood screws (ﬁgure 11). Lower the cooktop. Align

the knobs on the shafts and press down with even

pressure.

Figure 11

Cooktop

Countertop

Screw

Burner box

7

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

4. Models: 30" and 36" (36" X 21½") Coil Elements

Cooktops

-Thesecooktopsaredesignedtotvariouscutoutsizes.

The minimum and maximum cutout openings are

shown in ﬁgure 1.

-Ifcooktopistobeusedinnewinstallation,use

minimum cutout dimensions in ﬁgure 1.

- Attach cooktop to cabinet using wood screws through

holes in vertical walls of burner box.

- If cooktop is to be installed as a replacement in

an existing countertop opening (not exceeding

maximum cutout dimensions as shown in ﬁgure

1), the following steps must be taken:

1. Insert 4 screws and installation spacers through holes

in vertical walls of burner box (see ﬁgure 13).

2. Place cooktop into countertop opening and center

unit in cutout.

3. Tighten each screw ﬁnger tight or until spacers are

snug against burner box walls.

Figure 13

Burner box

Screw

Spacer

3. Models: 32" Coil Elements Cooktops

1. Place cooktop into countertop opening and center

unit in cutout.

2. Remove all surface units and drip bowls.

3. Unit clamp down information. Once unit is installed in

counteropening,youmustclampunitdownasshown

in ﬁgure 12.

4. Put back all surface units and drip bowls.

5. Make electrical connections as outlined in "Electrical

Connection" section.

Figure 12

Reach down through surface unit openings and install

the four hold down retainers with screws as shown. Be

certain cooking top is ﬁrmly retained to counter top.

Cooktop

Burner box

Holddownretainer

Countertop

Nylon spacer

4.Priortotighteninginstallationscrews,exertdownward

pressure on burner box to assure ﬂanges on burner

box rest ﬁrmly on counter. Tighten all screws evenly.

5. Unit clamp down information. Once unit is installed in

counteropening,youmustclampunitdownasshown

in ﬁgure 14.

6. Make electrical connections as outlined in "Electrical

Connection" Section.

Checking Operation

Refer to the Owner's Guide for operation.

CAUTION

Do not touch cooktop glass or elements.

They may be hot enough to burn.

Model and Serial Number Location

The serial plate is located under the cooktop or in the

burner box and can be seen by lifting up the main top of

unit.

When ordering parts for or making inquires about your

cooktop,alwaysbesuretoincludethemodelandserial

numbers and a lot number or letter from the serial plate

on your cooktop.

Before You Call for Service

Read the Avoid Service Checklist and operating

instructions in your Owner's Guide. It may save you time

and expense. The list includes common occurrences that

are not the result of defective workmanship or materials

in this appliance.

Refer to the warranty in your Owner's Guide for our

service phone number and address. Please call or write

if you have inquiries about your product and/or need to

order parts.

Figure 14

Toclampdown,insertbracketwithoffsetsideof

angle into slot on each side of unit. The screw should

then be run through bracket and against bottom of

counter. Tighten until draws down.

Countertop

Cooktop

Screw

Holddownretainer

Burner box

8

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

Only certain cooktop models may be installed

over certain built-in electric oven models.

Approved cooktops and built-in ovens are listed

by the MFG ID number and product code (see the

insert sheet included in the literature package and

cooktop installation instructions for dimensions).

36” Min.

(91.4cm) Min.

Use3/4”(1.9cm)plywood,

installedontworunners,

ﬂush with toe plate.

Base must be capable of

supporting 150 pounds

(68kg) for 27" models and

200 pounds (90kg) for 30"

models.

Cut an opening in wood base minimum 4” x 4”

(10.2X10.2cm),2”(5cm)fromleftsideller

panel,toroutearmouredcabletojunctionbox.

* If no cooktop is installed directly

overtheovenunit,5”(12.7cm)

maximum is allowed above the

ﬂoor.

208/240 Volt junction box

for built-in oven.

TYPICAL UNDER COUNTER INSTALLATION OF A SINGLE ELECTRIC BUILT‑IN OVEN

WITH AN ELECTRIC COOKTOP MOUNTED ABOVE

Approx. 3”

(7.5cm)

Cabinet side ﬁller panels

are necessary to isolate

the unit from adjoining

cabinets. Cabinet side

ﬁller height should allow

for installation of ap-

proved cooktop models

To reduce the risk of

personal injury and

tipping of the wall

oven, the wall oven

must be secured to

the cabinet(s) by

mounting brackets.

4½” (11.5cm)

Max.*

For typical under counter installation of an electric built-in oven see Figure below.

Note 1:4”x4”(10.2cmX10.2cm)openingto

route armored cable from cooktop to junction

box.

Approx. 3”

(7.5cm)

Unit will

overlap cutout

(minimum)

edges by 1"

(2.5cm)

See

Note 1

208/240Volt

junction box

for cooktop

CUTOUT DIMENSIONS

F. WIDTH G. DEPTH H. HEIGHT

27" (68.6cm)

Wall Oven

24

7

/

8

" (63.2cm) Min.

25¼" (64.1cm) Max.

23½" (59.7cm) Min.

27¼" (69.2cm) Min.

28¼" (71.8cm) Max.

30" (76.2cm)

Wall Oven

28½" (72.4cm) Min.

29" (73.7cm) Max.

23½" (59.7cm) Min.

27¼" (69.2cm) Min.

28¼" (71.8cm) Max.

Page is loading ...

Frigidaire FPEC3677RF Installation guide

This manual is also suitable for

Frigidaire FPEC3677RF Installation guide

in other languages

Related papers

Other documents