Installation
instructions
Sideboard
1/20
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
2/20
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
3/20
CL x 3 CR x 3
300 mm 300 mm 300 mm 300 mm
DL x 3 DR x 3
6 x 35 mm
6 x 30 mm
15 x 9 mm
3.5 x 14 mm
6 x 30 mm 4 x 35 mm 6 x 30 mm
3 x 12 mm
4 x 14 mm
C x 24
R x 2
Q x 2P x 2
J x 34 K x 5 N x 6 O x 2
D x 26 G x 20F x 16 H x 10E x 26
I x 1
4/20
x3
1
3
2
4
5
6
7
7
8
9
8
10
11
11
17
16
12
13
15
14 18
11
5/20
2CR x 3
300 mm
CL x 3
3 x 12 mm
C x 6
6 x 35 mm
D x 4
C x 6 D x 4
3
4
2
3
D
DDD
D
DC
C
C
C
C
C
C
C
C
C
C
C
C
CL
CR
CR
CR
D
D
D
CL
CL
CL
C
CR
300 mm 3 x 12 mm 6 x 35 mm
D
Fix slide rail(CL) to No.3 plate with screw(C)
as shown.
Insert quickfit screw(D) into both sides of
No.3 plate with screwdriver as shown.
Fix slide rail(CR) to No.4 plate with screw(C)
as shown.
Insert quickfit screw(D) into No.2 and No.4
plates with screwdriver as shown.
Please pay attention
to the holes where
the accessories are
inserted.
Please pay attention
to the holes where
the accessories are
inserted.
3
6/20
15 x 9 mm
E x 4
IIIIII
3
4
4
5
5
E
E
E
EE
E
Attach No.3 and No.4 plate to No.5,
turn cam lock(E) clockwise to tighten
as shown.
4
7/20
15 x 9 mm
E x 2
6 x 30 mm
F x 2
IIIIII
6
6
3
3
4
E
E
E
F
F
F
Attach No.6 to No.3 plate with wooden
dowel(F) and turn cam lock(E) clockwise
to tighten as shown.
5
8/20
E x 2 F x 2
IIIIII
2
2
6
6
3
4
E
E
E
F
F
F
15 x 9 mm 6 x 30 mm
Attach No.2 to No.6 plate with wooden
dowel(F) and turn cam lock(E) clockwise
to tighten as shown.
6
9/20
6 x 30 mm
F x 6
76 x 35 mm
D x 6
2
1
34
4
7
8
6
F
FF
FF
F
F
D
D
D
D
D
D
D
Slide No.7 and No.8 plates to available
slots as shown.
Insert wooden dowel(F) into No.2,3,4
plates as shown.
Insert quickfit screw(D) into
No.1 plate as shown.
8
10/20
15 x 9 mm
E x 6
96 x 30 mm
F x 6
IIIIII
2
1
1
3
3
4
4
4
6
6
8
7
2
2
E
F
F
F
F
F
FF
E
EE
E
E
E
1
Cover No.1 plate to the top and turn
cam lock(E) clockwise to tighten as
shown.
Slide No.7 and No.8 plates to available
slots as shown.
Insert wooden dowel(F) into No.2,3,4
plates as shown.
10
11/20
4 x 14 mm
N x 4
NNN
N
N
NN
N10
10
9
9
Fix leg 10 to No.9 plate with
screw(N) as shown.
11
12/20
6 x 35 mm
G x 6
9
9
6
1
2
2
3
4
G
G
G
G
G
G
G
Cover No.9 plate to the top and fix
with screw(G) as shown.
12
13/20
6 x 30 mm
H x 10 I x 1
H
H
H
H
HI
I
H
H
H
H
H
H
11
11
9
9
Fix leg 11 to No.9 plate with screw(H) as shown.
13
14/20
3.5 x 14 mm
J x 12 K x 2 O x 2 R x 2
JJ
O/R
12
13
JJ
JJJJ
J
JJ
J
JJ
O
OK
R
R
K
Fix hinge(O) to No.12 plate with screw(J), hinge(R)
to No.13 plate with screw(J) as shown.
Fix handle(K) to No.12 and 13 plates with screw(J)
as shown.
14
15/20
3.5 x 14 mm
J x 16
1
2
3
J
J
J
JJJ
JJ
JJJJ
J
J
JJ
12
13
Attach No.12 to No.2, No.13 to No.3 plates by
fixing hinge with screw(J) as shown.
15
16/20
16
17
17/20
4 x 35 mm
G x 12
G
G
G
G
G
G
15
15
16
16
14
17
14
x3
x3
Attach No.14 and No.15 to No.16
plate with screw(G) as shown.
Slide No.17 plate to available slots as shown.
18
18/20
19 15 x 9 mm
E x 12
6 x 35 mm
D x 12
3.5 x 14 mm
J x 6 K x 3
IIIIII
E
E
E
DD
DD
D
D
JJ
JJ
K
K
E
E
E
15
17
18
18
18
14
14
x3
x3
Insert quickfit screw(D) into No.18 plate
as shown.
Fix handle(K) to No.18 plate with screw(J)
as shown.
Attach No.18 plate to the component
and turn cam lock(E) clockwise to
tighten as shown.
20
19/20
3 x 12 mm
C x 12
300 mm
DL x 3
300 mm
DR x 3
C
C
C
DR
DL
C
DR
C
17
x3
Fix runner(DL) and (DR) to No.14
and No.15 plates respectively with
screw(C) as shown.
Page is loading ...
Page is loading ...
Page is loading ...
/
