Eaton DC 44/66 Green Motion User guide

Brand: Eaton

Model: DC 44/66 Green Motion

Type: User guide

This manual is also suitable for

DC 44

Figure 1. Front view of the xChargeIn DC 44/66 (with free space

for air inlet in mm)

Figure 3. The assembled charging station on the concrete base

Figure 2. Concrete base for charging station with positions of threaded

rods and electrical cable hole (in mm)

Figure 5. AC grid connectors inside xChargeIn DC 44/66

Figure 6. Grounding of the housing of xChargeIn DC 44/66 charging

station

Figure 4. xChargeIn DC 44/66 charging station wiring

Never turn on equipment when there is an evidence of re or structural damage. xChargeIn DC 44/66 must be installed only by professional installers.

Number Description

1Button indicator

2Color touchscreen display

3RFID reader

4LED display

5Emergency button

Number

Description

1xChargeIn DC 44/66

2RCD (considering

fire protection)

3Circuit breaker

Number

Description

1Threaded rods

2Electrical cable hole

Prior to installation it is required to download (www.eaton.com/xchargeindc44_66),

read, and understand the step-by-step instructions from the latest installation manual.

Eaton xChargeIn DC 44/66

Quick Start Guide

2. Electrical connections and unit switch-on 1. Preparation and mounting phases

During installation, unplug xChargeIn DC 44/66. Read and understand the safety instructions and warnings prior to installation.

Positioning the xChargeIn DC 44/66

• Ensure 300 mm free space on the left and right sides of the charging

station to ensure adequate air circulation (see Figure 1).

• Ensure easy access to the controls and connections.

• Eaton recommends installing the charging station at the front and

center of the parking space it services, each charging station should

serve only one parking space.

Mounting the xChargeIn DC 44/66

• Prepare a concrete base of 800 mm x 450 mm x 250 mm (width x

depth x height) with:

• 4 x M10 stainless steel threaded rods positioned according to

Figure 2.

• One hole of 48 mm diameter for the power input electrical cable

positioned according to Figure 2.

• The power input electrical cable is fed through the hole of the

concrete base into the enclosure of the charging station.

• Fix the charging station to the 4 x M10 stainless steel threaded rods

on the concrete base using at washers and M10 nuts.

• The appropriate types of nuts and at washers must be selected by

a professional installer.

• Figure 3 shows the charging station assembled on top of the

concrete base.

Instructions

• The unit is intended for indoor or outdoor installation.

• Optimal operation of the unit is in the temperature range

-25 °C to +45 °C.

• The unit must be transported and stored in indoor locations in

the temperature range -25 °C to +45 °C.

• The unit must be used and stored in locations with relative

humidity below 95 %.

• The unit must be used at a maximum altitude of 2000 m

above sea level.

• The unit must be used in locations free from acids, gases or

other corrosive substances.

• Do not install the unit in areas where highly ammable

substances are present.

• In case of missing accessories, contact your Eaton technical

support representative.

The contents of the xChargeIn DC 44/66 box

• xChargeIn DC 44/66 charging station,

• Quick start guide,

• Safety guidelines,

• EV plug(s), depending on customer conguration:

• CCS plug, cable, cable support and socket,

• CCS and CHAdeMO plugs, cables, cable supports and

sockets,

• Screws, cable glands and cable gland cap.

• Check that the door and housing of the xChargeIn DC 44/66 is

connected with the ground terminal (see Figure 6) and the whole

system is well grounded.

Unit switch-on

• Check that the equipment is correctly xed to the oor in

accordance with local regulations.

• Check that the AC GRID connections have been made correctly in

accordance with local regulations.

• Check that the EARTH connection (MANDATORY) has been made

correctly in accordance with local regulations.

• Perform checks on the continuity of the connections of the

protective conductor, insulation resistance, RCD triggering current,

triggering time, etc., in accordance with local regulations.

• Verify that the housing is closed and secured with the xing screws.

• If the checks listed above were successful, proceed as follows:

• Turn on the main AC GRID circuit breakers.

• Wait for the display to turn on.

• If applicable, configure the router to connect to the Eaton

Charging network manager.

• The unit is ready for use. Follow the instructions on the touchscreen

display.

Conguration and Commissioning

• Please refer to the installation manual for further details, available

from www.eaton.com/xchargeindc44_66.

Standard wiring

• In accordance with IEC 60364-7-722 a RCD is not required,

unless in TT and TN systems in areas where a re hazard

is present. There, a RCD with rated residual current of

<= 300 mA shall be used for re protection, in accordance

with IEC 60364-4-42 and local standards (Figure 4).

• The circuit breakers and the power cable minimal cross-

sections are overvalued to ensure the functionality of the

charging station with higher temperatures. Refer to the

installation manual and local standards for further details.

Electrical connections and terminals

• The electrical connection is made on the power supply

terminals located at the bottom left of the charger. Refer to

the appropriate section of the installation manual to open the

xChargeIn DC 44/66 housing.

• The power input electrical cables and communication cable

can be inserted from the bottom-left side of the charging

station. Remove the cable glands, if necessary.

• The electrical connection is made on the power supply

terminals located at the bottom-left of the charger (Figure 5).

• Please connect the phase (L1, L2, L3), neutral (N) and earth

(PE) wires of the GRID to the AC terminal block respecting

the correct assignment (Figure 5).

• It is possible to install the unit in an IT grid in accordance with

the local regulations and laws of the country of installation.

Eaton DC 44/66 Green Motion User guide

Brand: Eaton

Model: DC 44/66 Green Motion

Type: User guide

This manual is also suitable for

DC 44

Download PDF

report

Eaton DC 44/66 Green Motion User guide

This manual is also suitable for

Eaton DC 44/66 Green Motion User guide

Related papers

Other documents