2. Zenitel
  3. TMIV-1
TMIV-1

Zenitel TMIV-1 User guide

  • Hello! I've reviewed the Mounting Guide for the Zenitel Turbine Mini Video Intercom TMIV-1+ and its associated back boxes, TA-2, TA-3, and TA-32. This document includes comprehensive details on mounting procedures, dimensions, and camera field of view. I'm here to assist you with any questions regarding the installation or usage of these devices.
  • What is the recommended surface for flush mounting the TMIV-1+?
    What should be done if the surface is not sufficiently smooth?
    What type of screws are used to fasten the TMIV-1+ to the back box?
Mounting Guide
TMIV-1+ Turbine Mini Video Intercom
1 Turbine Mini Video Intercom
This document describes the dimensions, mounting procedure, and camera Field of View of the TMIV-1+ Turbine Mini
Video Intercom. Zenitel takes no responsibility for damages caused by improper or inadequate mounting.
Item Number Type Item Name
1008117010 TMIV-1+ Turbine Mini Video Intercom
1008140020 TA-2 Flush Mount 2-Gang Double-Depth Back Box
1008140030 TA-3 Flush Mount 2-Gang Back Box
1008140320 TA-32 On-Wall Back Box
2 Flush Mount 2-Gang Back Boxes - TA-2 & TA-3
TA-2 TA-3
LIt is recommended to utilize back boxes with weep holes at the bottom.
96 mm / 3.78?
48 mm
25 mm
23 mm
89 mm / 3.50?
89 mm / 3.50?
96 mm / 3.78?
46 mm
SIDE
SIDE
22 mm
1.81? 0.98?
0.90?
0.87?
1.89?
48 mm
25 mm
23 mm
46 mm
SIDE
SIDE
22 mm
96 mm / 3.78?
96 mm / 3.78?
0.87?
1.81? 0.98?
64 mm / 2.52?
64 mm / 2.52?
1.89?
0.90?
117 mm 43.5 mm
35 mm
46 mm
89.4 mm
84 mm
71.7 mm
3 Flush Mounting Procedure
1. Mount the 2-gang back box into the wall
2. Fasten the TMIV-1+ intercom to the back box with four #6-32 UNC countersunk-head screws
4 Camera Field of View
Flush Mount 2-Gang Back Box
TMIV-1+ Turbine Mini Video
#6-32 UNC Screws
#6-32 UNC Screws
Date: Dec 2021
A100K12125 [email protected]
DOC NO.
145°
50 cm
190 cm
50 cm
120 cm
109°
Vertical Angle Horizontal Angle
50 cm
317 cm
Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising from the information therein. Zenitel products are developed and marketed by Zenitel. The company’s Quality Assurance System is certified to meet
the requirements in NS-EN ISO 9001. Zenitel reserves the right to modify designs and alter specifications without notice.
ZENITEL PROPRIETARY. This document and its supplementing elements contain Zenitel or third-party information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited, if not otherwise explicitly agreed in writing with Zenitel. Any
authorized reproduction, in part or in whole, must include this legend: Zenitel – All rights reserved.
To attain the rated ingress
protection of IP44, ush
mounting of TMIV-1+ must only
be done on a surface that is
completely planar, smooth, and
clean. Any surface irregularities
must not exceed 0.5 mm. If this
is not achievable in a reliable
manner, appropriate sealant or
ller should be applied to seal
the gap between the station and
the wall. Optionally, the on-wall
back box TA-32 could be used.
/