Wren Phantom Whirlpool 1800 Installation, Use And Maintenance Manual

Wren
Brand
Wren
Model
Phantom Whirlpool 1800
Type
Installation, Use And Maintenance Manual

This manual is also suitable for

Phantom Whirlpool 1700
Phantom Whirlpool 1800
INSTALLATION, USE AND MAINTENANCE MANUAL
01_2015
WREN Living Ltd.
Page 2
Thank you for choosing a WREN Living Ltd. product. Welcome to our world of
total wellbeing.
We would like to remind you our products are built using excellent quality
materials that are accurately tested according to safety standards in force.
This guarantee of quality and comfort is accompanied by strong innovation
and sought-after design.
All we need to do now is wish you happy relaxation.
- DESCRIPTION OF PARTS
INTRODUCTION 4
THE USE AND MAINTENANCE MANUAL
SAFETY SPECIFICATIONS
INSTRUCTIONS FOR USE 12
- GENERAL FUNCTIONS
- USING PHANTOM WHIRLPOOL 1700 COMMAND PANEL
- USING COLOUR THERAPY COMMAND PANEL
- USING COMMAND PANELPHANTOM WHIRLPOOL 1800
MAINTENANCE 19
- SURFACE CLEANING
PARTS LIST 20
CONTENT
Page 3
INSTRUCTIONS FOR INSTALLATION 5
- MOUNTING ALL PARTS
- INSTALLATION OF THE BATHTUB
WARRANTY 21
- WARRANTY CONDITIONS
- WARRANTY CERTIFICATE
THE USE AND MAINTENANCE MANUAL
SAFETY SPECIFICATIONS
INTRODUCTION
This manual is a guide for safe use of our products, therefore you need to pay utmost attention when
reading it before using the product.
This manual is of fundamental importance, therefore it must be carefully kept, for any future consultation.
We reserves the right to make changes to the product, which are considered necessary, without prior
notification or replacement.
To correctly use the product, fully read the instructions in this manual. The manufacturer cannot be held
liable for any damage caused by improper use of the product.
Remember to check the installations comply with the instructions on the technical data sheet and the
installation manual of the product. The manufacturer cannot be held liable for any damage caused by
products that are tampered with or incorrectly repaired.
In the event of product malfunctioning, if the warranty is valid, exclusively contact authorised technical
staff.
Page 4
INSTRUCTIONS FOR INSTALLATION
Page 5
5 cm.
60 cm.
180°
Unpack the product
Turn upside down
ATTENTION
Please make sure the top surface of the
bath is protected against any possible
damage form abration from items on the
floor area when turning the bath upside
down to fit the leg assemblies.
Adjust the legs to the right height as per
picture.
1
2
3
INSTRUCTIONS FOR INSTALLATION
Page 6
1
2
Mount the water trap
5
(command panel side)
Mount the three brackets on the threaded
rods
6
INSTRUCTIONS FOR INSTALLATION
Page 7
Push them back
7
Take the front panel
(drain side)
Repeat the same operations
8
9
INSTRUCTIONS FOR INSTALLATION
Page 8
Mount the two supports with the four
screws.
Repeat the same operation for the end
panel.
10
Front panel
Mount, near the three threaded rods, the
steel springs with two screws each one
End panel
Mount, on the two blocks under the edge of
the bathtub, the steel springs with two
screws each one
11
INSTRUCTIONS FOR INSTALLATION
Page 9
90°
Set the angle at 90° between the panel and
the bathtub.
Adjust the position of the three brackets
and tighten the nuts.
Repeat the same operation with the end
panel.
Once you have adjusted all the panels,
remove them and continue the bathtub
installation
13
1
2
Mount the front panel on the bathtub
12
INSTRUCTIONS FOR INSTALLATION
Page 10
Connect the hydromassage control box to
the electricity supply.
ATTENTION
All Electrical work to be carried out only by
a quaiified Electrician and to be Certified
for compliance to all required Regulations
and current UK Standards
Connect the water trap of to the
floor drain with 1 and half inch (40mm).
bathtub
9
15
16
Using a level, put the bathtub perfectly
horizontal.
If you need, turn the adjustable feet
14
INSTRUCTIONS FOR INSTALLATION
Page 11
Put the temporary supports under the
panel.
Repeat the same operation for the front
panel.
Keep the panels in place, unscrewing the
two panel adjustable supports
18
19
Insert the end panel under the edge of the
bathtub.
17
GENERAL FUNCTIONS
INSTRUCTIONS FOR USE
CLICK CLACK DRAIN
PHANTOM WHIRLPOOL 1700
COMMAND PANEL
COLOR THERAPY COMMAND PANEL
Page 12
PHANTOM WHIRLPOOL 1700
CLICK CLACK DRAIN
PHANTOM WHIRLPOOL 1800
COMMAND PANEL
PHANTOM WHIRLPOOL 1800
HYDROMASSAGE
This device allows you to take advantage of the
hydromassage without the physical presence
of the device generating the hydromassage,
clearly improving the product ergonomics.
For system functioning, see the control panel
specifications (see page 15 and 17).
Page 13
LED COLOUR THERAPY
Led colour therapy on the product is positioned
in the external grooves and, through the
transparent part of the bath, enabling light
diffusion.
The absence in the bath of the light generation
device clearly improves product ergonomics
and reduces the risk of breakage.
For system functioning, see the control panel
specifications (see page 16-17-18).
DESCRIPTION OF PARTS
The Phantom Whirlpool bath includes a
patented hydromassage system.
CLICK CLACK DRAIN
Fig.1 Fig.2
Fig.3
To close the drain press the plug (Fig. 1)
To open again, bring the plug to the original
position (Fig. 2)
It can be internally accessed for cleaning by
unscrewing the plug.
DESCRIPTION OF PARTS
Page 14
WHIRLPOOL KEY
KEY1
KEY2
KEY1: Disinfection On/Off
KEY1: Whirlpool On/Off
KEY2: Venturi On/Off
DISINFECTION ON/OFF KEY
VENTURI ON/OFF KEY
To turn on the hydromassage function, fill the bath up to 5 cm., over the
hydromassage slit (if the level goes below this slit, the function deactivates
in 3 seconds).
Press KEY 1 to switch on the pump generating the supply in the bath with
pressurised water: the function is confirmed with the indicator light on, on
the key.
If you want to stop the function, simply press KEY 1 again and the
simultaneous switching off of the indicator light confirms it is off.
The function however has an automatic safety stop after 15 minutes.
The function activates in the presence of a sufficient water level in the bath
through prolonged pressure on KEY 1 ( approx. 5 seconds ) to request
activation of the function, the indicator light starts to flash, to confirm the
disinfection cycle press KEY 1 again during the third flash of the indicator
light. The active function is signalled by fast flashing of the indicator light.
The function automatically stops after 5 minutes.
This function can only be switched on if the Whirlpool is already on.
To switch on, press KEY 2. The indicator light switches on to confirm
activation. The bath starts to fill with water mixed with air, with a whirling
effect. To stop it, simply press KEY 2 again and the simultaneous switching
off of the indicator light confirms it is switched off.
If you want to stop the function, simply press KEY 1 again and the
simultaneous switching off of the indicator light confirms it is off.
Page 15
USING PHANTOM WHIRLPOOL 1700 COMMAND PANEL
KEY2
KEY3
KEY2: Manual colour change On/Off
KEY1: Colour Therapy On/Off
KEY3: Automatic colour change On/Off
KEY1
COLOUR THERAPY ON/OFF KEY
MANUAL COLOUR CHANGE KEY
Premete il TASTO 1 per attivare la funzione e si accenderà la luce bianca.
A questo punto è possibile scegliere fra un cambio manuale tra 8 colori fissi
e un cambio colore automatico. Per fermare la funzione, basta agire sul
TASTO 1.
Per passare al colore successivo premere il TASTO 2.
- white
- yellow
- orange
- green
- indigo
- light blue
- blue
- red
- fuchsia
COLOUR THERAPY ON/OFF KEY
Press KEY 1 to activate the function and the white light switches on.
At this point, you can choose to manually change between 8 fixed colours
and an automatic colour change. To stop the function, simply press KEY 1.
To change to the next colour press KEY 2.
The sequence of fixed colours is as follows:
Press KEY 3 to activate the function. This cycle gives a complete experience
of the entire colour range that changes gradually.
USING THE COLOUR THERAPY COMMAND PANEL
Page 16
ON/OFF KEY
Alla prima accensione il tasto sarà retroilluminato di blu e tutti gli altri
saranno spenti, ad indicare che tutte le funzioni sono inibite all’uso.
Alla prima pressione del tasto la retroilluminazione del tasto passa a
rosso, mentre tutti gli altri si accendono in blu ed il sistema è pronto
all’uso.
Successive pressioni del tasto riportano il sistema in stato di riposo,
spegnendo la retroilluminazione di tutti i tasti e spegnendo tutte le
funzioni attive (ad accezione dello scarico come spiegato più avanti).
Page 17
On/Off Whirlpool Light Colour
therapy
Disinfection
On first switch-on, the key will be backlit in blue and all others will be
off, to indicate all the functions have inhibited use.
On first pressing the key, the backlighting on the key changes to red,
while all the others switch on in blue and the system is ready for use.
After pressing the key, the system returns to standby status, switching
off the backlighting of all the keys and switching off all the active
functions (except drainage as explained later).
USING PHANTOM WHIRLPOOL 1800 COMMAND PANEL
WHIRLPOOL KEY
Con sistema in On e livello d’acqua in vasca sufficiente, la pressione
del tasto attiva l’idromassaggio, che rimarrà attivo sino alla nuova
pressione del tasto o per un tempo massimo di 20 minuti.
Lo stato di On della funzione è identificato dalla retroilluminazione di
colore rosso dell’icona.
Se premuto il tasto ma non vi è sufficiente livello acqua in vasca
verranno dati 3 lampeggi di rosso ad indicare l’anomalia.
(vedi
pg. 7)
LIGHT KEY
Con sistema in On e livello d’acqua in vasca sufficiente,
del tasto attiva l’illuminazione a led bianca, funzione che che rimarrà
attiva sino alla nuova pressione del tasto o per un tempo massimo di
60 minuti.
Lo stato di On della funzione è identificato dalla retroilluminazione di
colore rosso dell’icona.
Se premuto il tasto ma non vi è sufficiente livello acqua in vasca
verranno dati 3 lampeggi di rosso ad indicare l’anomalia.
la pressione
(vedi
pg. 7)
With the system On and a sufficient level of water in the bath, press
the hydromassage on key, which stays on until pressed again or for a
maximum time of 20 minutes.
The On status of the function is identified by the backlighting in red
on the icon.
If the key is pressed but there isn't a high enough water level in the
bath, three red flashes are given to indicate an anomaly.
With the system On and a sufficient water level in the bath, press the
key to activate the white led light, a function which stays on until the
key is pressed again or for a maximum time of 60 minutes.
The ON status of the function is identified by the backlighting in red on
the icon.
If the key is pressed but there isn't a high enough water level in the
bath, three red flashes are given to indicate an anomaly.
LIGHT COLOURS KEY
Con luce accasa, la pressione del tasto fa cambiare il colore delle luce
tra gli 8 tonalità fondamentali. Il tasto “luci” rimarrà illuminato di rosso,
mentre il tasto “colori luci” si illuminerà di rosso per i 2 secondi dopo la
pressione dello stesso, per poi tornare blu.
Non sono previste pressioni prolungate per un avanzamento veloce
dei colori.
With the light on, pressing the key changes the colour of the lights to
8 basic colours. The "lights" key will remain lit in red, while the «light
colours" key will light up in red for 2 seconds after it is pressed, and
then return to blue.
No prolonged pressing is planned for fast colour progression
PHANTOM WHIRLPOOL 1800 COMMAND PANEL
Page 18
DISINFECTION KEY
Con sistema in On, disinfettante
sufficiente nel serbatoio e tutte le funzioni in stato di Off
(cromoterapia compresa), la pressione del tasto abilita un ciclo di
pulizia automatico.
Lo stato di on del ciclo sarà identificato del tasto illuminato di rosso.
Essendo la funzione di disinfezione un ciclo completamente
automatico, è prevista una procedura di sicurezza per la sua
attivazione composta da una doppia pressione del tasto.
Alla prima pressione verranno fatti 3 lampeggi in blu del tasto: se entro
il terzo lampeggio viene data conferma la funzione parte e la retro-
illuminazione rimane accesa in rosso fisso, altrimenti la funzione
abortisce e la retroilluminazione torna ad essere blu.
Se viene premuto il tasto quando una delle condizioni non è
soddisfatta (livello in vasca, livello disinfettante o funzioni attive), verrà
data segnalazione di anomalia facendo tre lampeggi in rosso del
tasto.
livello d’acqua in vasca sufficiente,
With the system On and a sufficient level of water in the bath, sufficient
disinfectant in the tank and all the functions Off (including colour therapy)
press the key to enable an automatic cleaning cycle.
cycle.
The on status of the cycle will be identified by the red lighting key.Since
the disinfecting function is an automatic, complementary cycle, a safety
procedure is planned for its activation by double pressing the key.
On first pressing, the key will flash three times in blue, if within the third
flash confirmation is given, the function starts and the backlighting stays
on and fixed red, otherwise the function aborts and the backlighting turns
blue again.
If the key is pressed when one of the conditions is not met (level in bath,
disinfectant level or active functions), an anomaly signal is given with the
key flashing red three times.
ok
MAINTENANCE
GENERAL SURFACE CLEANING
I prodotti generici, quali i liquidi detergenti neutri possono essere utilizzati per la normale pulizia delle
superfici. E’ consigliabile applicare il prodotto con un panno morbido , risciacquando accuratamente
con acqua.
Sono da escludere tutti i detersivi specifici per la rimozione del calcare. A causa della loro composizione
alcalina possono danneggiare le superfici dei prodotti come le rubinetterie o altre finiture metalliche.
ASSOLUTAMENTE NON USARE PRODOTTI ABRASIVI, SOSTANZE A BASE ALCOLICA,
ACETONE O ALTRI SOLVENTI.
ASSOLUTAMENTE NON UTILIZZARE SPUGNE CON RETINE METALLICHE O ABRASIVE.
TAP CLEANING
NON USARE PRODOTTI ABRASIVI, SOSTANZE A BASE ALCOLICA,
Generic products, such as neutral liquid detergents can be used for normal surface cleaning. You are
advised to apply the product with a soft cloth, rinsing carefully with water.
Do not use all specific detergents for limescale removal.
Due to their alkaline composition, they can damage the surfaces of the products such as taps and other
metal finishes.
To dry, you are advised to use a deer skin cloth.
To maintain surface shine, periodically use common polish.
NEVER USE ABRASIVE PRODUCTS OR SUBSTANCES WITH AN ALCOHOL,ACETONE OR OTHER
SOLVENT BASE.
NEVER USE SPONGES WITH A METAL OR ABRASIVE MESH.
For all surfaces in chrome, brass and gold, you can use cloths or sponges soaked in clean water.
NEVER USE ABRASIVE PRODUCTS OR SUBSTANCES WITH AN ALCOHOL, ACETONE OR OTHER
SOLVENT BASE.
NEVER USE SPONGES WITH A METAL OR ABRASIVE MESH.
liquid
soap
Page 19
PARTS LIST
Page 20
cod. 62221 - Phantom Whirlpool 1700
cod. 62222 - Phantom Whirlpool 1800
cod. 62223 - Phantom Whirlpool 1700 Front Panel
cod. 62224 - Phantom Whirlpool 1700 End Panel
cod. 62225 - Phantom Whirlpool 1800 Front Panel
cod. 62226 - Phantom Whirlpool 1800 End Panel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Wren Phantom Whirlpool 1800 Installation, Use And Maintenance Manual

Wren
Brand
Wren
Model
Phantom Whirlpool 1800
Type
Installation, Use And Maintenance Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Other documents