AMERICH Whisper Collection User manual

Brand: AMERICH

Model: Whisper Collection

Type: User manual

Whisper Collection

INSTALLER: To be removed for use by the occupant

User Guide

1. Prior to Installation:

• Remove protective plastic and packaging and carefully inspect for any

damage.

• Check tub for correct model name, size, color and trim nish.

• The tub MUST be tested while pump, electrical systems, and piping

(plumbing) are accessible.

• If there are any issues, do not install and report the issues immediately

to our factory or the authorized dealer.

2. WARNING: To avoid injury, exercise caution when entering or exiting the

bathtub.

3. DANGER/WARNING: To reduce the risk of injury, do not permit children or

persons with a disability to use this unit unless they are closely supervised

at all times. Risk of accidental injury or drowning. Children should not use

hydromassage bathtub without adult supervision.

4. WARNING: Risk of accidental injury or drowning; Do not use hydromassage

bathtub unless all suction guards are installed to prevent body and hair

entrapment.

5. This product is for indoor use only. Use the bathtub only for its intended

purpose as described in this manual and do not use attachments or accessories

which are not recommended by manufacturer.

6. Never drop or insert any objects into any openings.

7. Persons with long hair should wear a bathing cap when using the bathtub.

8. WARNING: Risk of accidental injury or drowning; do not use drugs or alcohol

before or during the use of a bathtub or hydromassage bathtub equipped

with heater to avoid unconsciousness or possible drowning.

9. WARNING: Risk of Fetal Injury; pregnant or possibly pregnant women should

consult a physician before using a hydromassage bathtub equipped with

heater.

10. The bathtub must be connected to an electrical supply circuit that is

protected by a ground fault circuit interrupter (GFCI) which is provided

by the installer. The GFCI should be tested periodically to ensure that it is

working properly.

11. Keep all appliances, such as radios and hair dryers, a safe distance from the

bathtub.

12. For permanently connected units, green colored terminal (or a wire connector

marked “G”, “GR”, “Ground”, or “Grounding”) is provided within the terminal

compartment. To reduce the risk of electrical shock, connect this terminal or

connector to the grounding terminal of your electrical service or supply panel

with a conductor equivalent in size to the circuit conductors supplying this

equipment.

13. Install in accordance with manufacturer’s installation instructions. Failure

to comply with all instructions, requirements and warnings contained in this

manual creates a serious hazard to the bathtub user and may result in serious

personal injury.

Warning: The causes, symptoms, and eects of hyperthermia may be described

as follows: Hyperthermia occurs when the internal temperature of the body

reaches a level several degrees above the normal body temperature of 98.6. The

symptoms of hyperthermia include an increase in the internal temperature of the

body, dizziness, lethargy, drowsiness, and fainting. The eects of hyperthermia

include (1) failure to perceive heat, (2) failure to recognize the need to exit

the spa or hot tub, (3) unawareness of impending hazard, (4) fetal damage

to pregnant women, (5) physical inability to exit the spa or hot tub, and (6)

unconsciousness resulting in the danger of drowning.

Warning: The use of alcohol, drugs, or medication can greatly increase the risk

of fatal hyperthermia.

SAVE THESE INSTRUCTIONS

Americh baths are assembled complete and ready for installation.

Immediately upon receiving the bath and removal of packing, INSPECT

the unit for freight damage. Any claims for damage, whether apparent

or hidden, must be made to freight carrier immediately, in order for them

to assume all associated costs. Should inspection reveal any defect in the

nish, DO NOT INSTALL THE BATH. Damage or defect to the nish claimed

after the bath is installed is excluded from the warranty. The warranty DOES

NOT cover labor or materials to remove or re-install the bath.

PRIOR TO INSTALLATION

Check to ensure that:

1. The installation will conform with all applicable Federal, State and Local

Building Codes & Regulations;

2. The unit is the correct model and color;

3. There has been no shipping damage;

4. The “notice” or “warning” tags on the bathtub have been read and thoroughly

understood;

5. The interior of the tub will be protected during installation;

6. Make sure sub oor is level.

DURING INSTALLATION

Check to ensure that:

1. Bathtub is not hanging from the rim. Bath must be supported from the oor

(See Figure 1, Page 4.)

2. An access panel with minimum dimensions of 16” height by 20” width is

required. See specication sheet for proper access panel location.

3. All Bathtubs with seats must have additional support for each seat.

4. All building materials and wiring should be routed away from the pump body

or other heat producing components of the unit.

ELECTRICAL REQUIREMENTS

Manufacturer recommends a dedicated 20 amp circuit breaker for each power

cord supplied on your whirlpool bathtub. WARNING - When using electrical

products, basic precautions should always be followed, including the following:

1. DANGER: Risk of electric shock. Connect only to a supply circuit protected

by a Class A ground-fault circuit-interrupter (GFCI). Test on a routine basis.

2. Grounding is required. The unit should be installed by a qualied service

representative and grounded.

3. (For built-in and custom units) install to permit access for servicing.

4. Supply 110 Volt electrical outlet. This circuit must be protected by a ground

fault circuit interrupter (GFCI.)

5. Plug supply cord(s) into electrical outlet.

6. To test the GFCI, do the following:

a. Push the test button;

b. Check to see that power has been interrupted;

c. Push the reset button;

d. Check to see that power has been restored.

If the GFCI does not operate properly during the test, there is a ground current

owing indicating the risk of electric shock. Do not use this unit. Disconnect the

unit and have the problem corrected by a qualied service representative before

using.

Refer to Operating Instructions for system operations and wiring diagrams.

Warning: Whirlpool bathtubs utilize acrylic and fiberglass materials (which are inherently slippery surfaces), electricity, water, air pressure and suction. The

following basic safety precautions should always be followed when using your bathtub.

CAREFULLY

READ AND FOLLOW ALL INSTRUCTIONS

before attempting to operate your whirlpool or Airbath® Bathtub.

IMPORTANT SAFETY INSTRUCTIONS:

pertaining to a risk of re, electric shock, or injury to persons

installation instructions

PREPARE SETTING BED

1. Prepare tub setting bed using lightweight cement, plaster, gypsum or x-all

bed approximately 1” or 2” thick (gure 1).

2. Place the tub in the proper position using the oor, not the deck or rim, as

the support, and set it in the bedding compound (gure 2).

COMPLETE BATH INSTALLATION

Level the top of the bathtub in both directions, using a 4 ft. level, to ensure

drainage. Bring the tile or nished surface to tub deck and then seal. Seal

edges as shown (See Figures 3, 4 or 5.)

CLEAN-UP AFTER INSTALLATION

When cleaning up after installation, do not use abrasive cleaners as they

may scratch and dull the surface. Use warm water and a liquid non-abrasive

detergent to clean the surface.

Stubborn stains, paint or tar can be removed with turpentine or paint

thinner. Do not allow cleaners containing petroleum distillates to remain in

contact with bath surface for long periods of time. Plaster can be removed by

scraping with a wood edge. Do not use metal scrapers, wire brushes, or other

metal tools.

TESTING OPERATIONS

To check proper function of your newly installed bathtub take the

following steps:

1. Remove all debris and residue before lling the tub with water

2. Fill the tub with water until the highest whirlpool jet is covered by at least

2” of water.

3. Examine tub and system carefully for leaks.

4. Turn on system and allow tub to run approximately 2-3 minutes

(Whirlpool only).

5. Allow water to sit for 10 minutes and check for leaks.

6. Open drain and empty tub.

7. Wipe up excess water with a soft, damp sponge.

When cleaning up after installation do not use abrasive cleaners, steel wool,

scouring pads or harsh chemicals. For cleaning procedures refer to the “Care

and Maintenance” section.

gure 1

Choose the installation option that applies to your particular installation and follow the instructions. Be sure to take any necessary precautions to keep tub

protected during installation.

gure 2

gure 5

gure 4

gure 3

TECHNICAL SERVICE

For technical service or eld service, you must:

1. Locate the product identication tag. This tag includes all pertinent

information specic to your product, including the model, size, color, date

of manufacture and ID number.

2. Write down all information and have it available when contacting the

manufacturer.

The manufacturer maintains strict guidelines for eld service and will require

this information in order to facilitate your request and determine if a eld

service representative is required.

Warning: Any service should be performed by a qualied licensed service

agent.

CARE AND MAINTENANCE

Soap residues and mineral deposits are the enemies of your bathtub, particularly in areas where there is hard water. However, cleaning your bathtub at regular intervals

and using proper cleaning agents, you can help your bathtub retain its original sparkling look. DO NOT USE abrasive cleaners, as these products will damage the

bathtub surface and metallic nishes. A non-abrasive cleaner is recommended.

Your bathtub does not require the use of special cleaning agents or chemicals.

Normal cleaning is simple and easy.

operating instructions

1 Engages the system with jets on HIGH

2 Engages the system with the jets on LOW

3 Engages the system and pulsates the water ow

4 OFF Button Turns the jets OFF

1 2 3 4

5 LIGHT Button used to control the optional mood light.

• Pressthe“Light”buttontoturnonthemoodlight

• Thelightdisplays7vividcolorsand2sequencingsettings.

• Tochangethelightcolor,pressthe“Light”buttontoturnitoandafteronesecondpressitagaintoturniton.

• Thecolorsequenceisasfollows:BrightWhite,AquaBlue,SoothingBlue,OceanBlue,MajesticGold,ShamrockGreen,FieryRed,ChameleonMode,Party

Mode

• Intheeventthatthelightisleftturnedon,itwillautomaticallyturnoafter2hourscontinuousoperation.

1. Preparation and Cleaning

• Drain the bathing well of all water.

• Rotate the jet assembly to remove from jet case.

• Disassemble the jet assemblies (3 pieces each) and place them in the sink. Use a non-abrasive antibacterial cleaner to

remove any visible residue - rinse with fresh water.

• Use a non-abrasive antibacterial cleaner to clean the bathing vessel, jet cases, drain stopper and overow mechanism–

rinse with fresh water.

2. Disinfection

• Spray the surface area of the jet assemblies and bathing vessel until thoroughly coated with a registered disinfectant.

• Allow to set for the required disinfection contact period (refer to manufacturer’s specications) then rinse surfaces with

fresh water.

3. Reassembly

• Dry the jet assemblies and bathing vessel.

• Reassemble and replace jets by aligning the 11 o’clock

To preserve the surface nish, annual waxing is recommended. Use a high-grade paste-type automotive wax.

WHISPER COLLECTION

Residential Limited Warranty

Americh Corp. warrants that its bathtubs are free of defects in manufacture and materials so long as (1) the bathtub is installed and maintained according to Americh Corp.

recommended installation and maintenance procedures, (2) use of the bathtub is limited to personal, family or household purposes and (3) any defects are not the result

of unauthorized or unreasonable use.

This warranty applies only to the rst consumer purchaser and is limited in time from the date of original purchase for a period of ve (5) years with respect to the tub and

twelve (12) months with respect to the electronics and accessories. This warranty does not apply to subsequent owners, transferees or users.

This warranty does not apply to or cover defects, damage or failure caused by the freight carrier, installer, user or other person, or resulting from, without limitation, any

of the following: improper handling, modication of any type, improper installation, misuse, incorrect operation, lack of proper routine maintenance, the use of improper

cleaners or abrasives, accidents or acts of God. Nor does it apply to eects of normal wear and tear.

Alteration, customization or modication of the tub, the water system, the electronics, any accessory or any other part voids this warranty.

If a defect or malfunction is discovered during normal residential use notify Americh Corp. in writing within ten (10) days of discovery, setting forth the date of discovery,

a description of the defect or malfunction, the name and address of the installer of the bathtub, electronics and accessories and the date and address of installation and

the type or style of the bathtub. Americh Corp., will, at its election, repair, replace or make appropriate adjustments. In all cases a reasonable time must be allowed for

commencement and completion of warranty repairs.

Americh Corp. is not responsible for labor charges or other charges related to the removal or installation or other costs involved in repairing or replacing the bathtub or the

expense of shipment to or from the factory, except where provided by applicable law.

To obtain information about or performance of warranty obligations contact Americh Corp. 13212 Saticoy Street, North Hollywood, CA 91605 or by calling (818) 982-1711

and asking for Customer Service.

No other company or person has any authority to make any warranties or representations concerning Americh Corp. or the product. Accordingly, Americh Corp. is not

responsible for any such warranties or representations.

THIS LIMITED WARRANTY IS THE SOLE WARRANTY FOR YOUR AMERICH CORP. PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

AMERICH CORP. HAS NOT MADE AND DOES NOT MAKE ANY WARRANTY OR REPRESENTATION, WHATSOEVER, EXPRESS OR IMPLIED, ABOUT THE CONDITION, MERCHANTABILITY, DESIGN, OR OPERATION OF THE

BATHTUB OR ITS FITNESS FOR ANY PARTICULAR USE OR PURPOSE, OR THE QUALITY OF THE MATERIALS OR WORKMANSHIP IN THE BATHTUB, THE ELECTRONICS OR THE ACCESSORIES OR ANY OTHER REPRESENTATION

OR WARRANTY BEYOND THE TERMS OF THIS LIMITED WARRANTY.

AMERICH CORP. DISCLAIMS AND SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION, IN WHOLE OR IN PART, OF WARRANTIES OR THE EXCLUSION OF SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. THEREFORE, THE ABOVE

LIMITATIONS OR EXCLUSIONS MAY NOT BE APPLICABLE TO YOU.

West Coast

13212 Saticoy Street

N. Hollywood, CA 91605

818.982.1711 Tel

818.982.2764 Fax

East Coast

10700 John Price Road

Charlotte, NC 28273

704.588.3075 Tel

704.588.3166 Fax

800.453.1463