Parkside PHKPG 150 A1 Operating And Safety Instructions Manual

Brand: Parkside

Model: PHKPG 150 A1

Type: Operating And Safety Instructions Manual

Parkside PHKPG 150 A1 - is a butane powered hot glue gun for gluing wood, cardboard, and similar materials over a short time period and exclusively with 11 mm Ø glue sticks. It is suitable for private use in the hobby and craft area for brief durations and is not suitable for long-duration use. The hot glue gun is equipped with a gas regulator, a gas supply regulator, a piezo ignition, a nozzle, and an inspection glass for the heating chamber. It has a stand for safe placement when not in use, and a trigger for controlling the flow of glue.

IAN 285747

GAS HOT GLUE GUN

PHKPG 150 A1

Operating and safety instructions

Table of contents

1. Scope of delivery / parts list ................................................................................................ 04

Description of the parts

.............................................................................................................................................................04

2. General

.............................................................................................................................................. 04

Symbols used

.....................................................................................................................................................................................04

3. Safety

.................................................................................................................................................. 05

Appropriate use

...............................................................................................................................................................................05

Safety instructions

..........................................................................................................................................................................05

4. Before Use

........................................................................................................................................ 08

Checking the product and scope of delivery

........................................................................................................08

Filling the gas tank (Fig. A)

....................................................................................................................................................08

Inserting the glue stick (Fig. B)

............................................................................................................................................08

5. Usage

.................................................................................................................................................. 09

Lighting the hot glue gun (Fig. C)

.....................................................................................................................................09

Gluing applications

......................................................................................................................................................................10

6. After finishing work

................................................................................................................... 10

7. Storage and transport

..............................................................................................................11

8. Maintenance and spare parts

..............................................................................................11

Maintenance and repairs

........................................................................................................................................................11

Cleaning

..................................................................................................................................................................................................11

9. Troubleshooting

.............................................................................................................................12

10. Technical specifications

.............................................................................................................12

11. Disposal

..............................................................................................................................................13

Disposing of the used device

............................................................................................................................................... 13

Disposal of packaging

............................................................................................................................................................... 13

Instructions for disposal of the gas cartridge

.........................................................................................................13

12. Warranty

...........................................................................................................................................13

1. Scope of delivery / parts list

2. General

Gas hot glue gun

Glue port

Gas regulator marking

Gas supply regulator

Handle

Gas refilling valve

Trigger

Stand

Piezo ignition

Nozzle

Inspection glass for heating chamber

Ventilation opening

2 Glue sticks

Butane refill cartridge Art. 1500002692

Description of the parts

This manual belongs to this product. It contains important information on safety, usage and

maintenance. Read the manual carefully before using the product. Pay particular attention

to the safety instructions and warnings. Failure to follow the instructions given in the manual

may result in serious injuries or damage to the product. Always include the manual when you

give the product to others. Keep this manual in a safe place for future reference.

Symbols used

Follow the warnings and safety instructions!

The following symbols and key words will be used in this manual, on the product or the

packaging.

3. Safety

Appropriate use

This product is only suitable for private use in the hobby and craft area for the following

purposes:

• For gluing wood, cardboard and similar materials over a short time period and

exclusively with 11 mm Ø glue sticks

Any other use of the product is expressly forbidden and is considered as misuse. The

manufacturer cannot be held responsible for damage or injury caused by misuse of the

product. Examples of misuse are given in the following non-exhaustive list:

• Use of unsuitable accessories

• Use and maintenance of the product by someone who is not familiar with the product

and/or who lacks suitable experience

• commercial, business-related, industrial or excessive use of the product

Use the accessories according to these instructions. Failure to follow the instructions in

the manual may lead to serious injury and may invalidate the guarantee. Comply with

applicable local or national regulations concerning the use of this product. Do not make

any modifications to the product. Any modification to the product may be dangerous and is

prohibited.

Read the manual

WARNING! Hot surface

Safety instructions

WARNING! Read the safety instructions carefully. Failure to follow the

safety warnings and instructions may result in ﬁre, explosion and/or serious

injuries.

a. Always keep the hot glue gun out of reach of children.

b. Keep the hot glue gun away from your face and away from your clothing when

lighting.

c. The nozzle and other accessible parts are very hot even after the ﬂame has

gone out. Do not touch.

d. Do not expose the hot glue gun to heat more than 50°C or to sunlight for a

long time.

e. The hot glue gun is designed for private use in the hobby and craft area and

for brief durations and is not suitable for long-duration use. Switch off the hot

glue gun during breaks and after a maximum of half an hour of usage for

complete cooling by closing the gas supply regulator.

f. Never work overhead. Hot, molten glue could drip down and injure you.

g. Use the hot glue gun only in well-ventilated places and away from ignition

sources or ﬂammable objects.

h. Do not use the hot glue gun if it is leaking or damaged, or if it is not working

properly.

i. Do not disassemble or open the hot glue gun.

j. Do not make any modiﬁcations to the hot glue gun. The assembly and factory

settings should not be altered. – Only replacement parts recommended by the

manufacturer may be used. It can be dangerous to modify the settings or make

changes to the hot glue gun, to remove parts or to use replacement parts other

than those recommended by the manufacturer.

k. Repairs to the hot glue gun should only be carried out by the manufacturer or

by an authorised service centre.

l. Switch off the hot glue gun and place it in its stand during breaks and when not

in use.

m. Wait for one minute after reﬁlling before lighting the hot glue gun.

n. Be careful when using the hot glue gun near ﬂammable materials and

remember that heat can be conducted to concealed ﬂammable materials.

o. Never leave the hot glue gun unattended when switched on.

p. Ensure that the ﬂame is completely extinguished after use. Open the stand of

the hot glue gun and allow the hot glue gun to cool down completely on the

stand before putting it away. Otherwise there is risk of ﬁre.

q. The ﬁlled gas tank contains ﬂammable pressurised gas. Take care not to

heat the reﬁllable gas tank. Do not expose the hot glue gun to temperatures

exceeding 50°C / 120°F or to prolonged sunlight. Otherwise there is risk of

bursting or explosion.

r. Read the reﬁlling instructions carefully. Incorrect reﬁlling may lead to accidents.

s. Do not use the hot glue gun in surroundings where ﬂammable fumes,

ﬂammable liquids or explosive materials are present. Otherwise there is risk of

ﬁre or explosion.

t. Do not light the hot glue gun near your face, hands, clothing or ﬂammable

materials. Do not light and direct the hot glue gun at others. Otherwise there is

risk of burns.

u. Maintain a safe distance of at least 0.5 m on the side from all objects, as well

as a min. distance of 1 m from objects over the device.

v. The air outlet of the hot glue gun releases hot air. Ensure that the hot glue gun

is always switched off and placed on the integrated stand even during short

breaks, to avoid igniting the work surface or other objects. Do not direct the hot

air outlets towards your eyes, face or others. Otherwise there is risk of burns.

w. Do not inhale the fumes, as they may be poisonous.

x. The glue nozzle becomes extremely hot during and remains hot for a period

after use. Take care to protect yourself from accidental burns.

y. Risk of burns! Do not touch the hot glue or the nozzle with your ﬁngers. Never

point the hot glue gun towards others or animals - the hot glue should not come

into contact with persons or animals.

z. If hot glue comes into contact with your skin, hold the affected area under cold

running water. Do not attempt to pull off any glue which is stuck to the skin.

aa. Never attempt to pull glue sticks out of the device.

bb. Never use inﬂammable liquids to clean the workpieces.

cc. This device is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge.

Children should be supervised to ensure that they do not play with the device.

Caution! Danger of ﬁre, burning and/or explosion!

• Switch off the hot glue gun by closing the gas supply regulator and

ensure that the ﬂame is off.

• Allow the hot glue gun to cool completely.

• Fill the tank in a well ventilated place, in an area free of ames or sources

of ignition and at a safe distance from others. Smoking is prohibited when

ﬁlling the tank.

• Use only butane reﬁll cartridges, for example commercially

available cigarette lighter gas. Do not use pure isobutane or propane-

butane mixes.

Filling the gas tank (Fig. A)

Inserting the glue stick (Fig. B)

4. Before Use

Checking the product and scope of delivery

• Take the hot glue gun and accessories out of the packaging

• Check whether the delivery is complete (see chapter "Scope of delivery / parts list")

• Check the hot glue gun and accessories for damages.

• Do not use the hot glue gun if it is damaged or parts are missing. Contact the manufacturer

via the service centre listed in the "Warranty" chapter.

• Place the nozzle of the gas canister against the gas refill valve (6) and press it in. Use a

suitable adapter if necessary.

• Take the nozzle of the gas canister out of the refill valve of the device before the gas

begins to flow out.

Wait for at least a minute before igniting the gun for the first time to allow the gas to stabilise.

• Insert a glue stick into the glue port (2) as shown.

Note! Risk of damage!

• Always switch off the hot glue gun and place it on the integrated stand

even during short breaks.

• Never use the hot glue gun for more than 30 minutes. After this, allow

the hot glue gun to cool down completely before using it again.

Lighting the hot glue gun (Fig. C)

5. Usage

Ignition

Gas supply

open

Inspection glass

• Push the gas supply regulator (4) upwards and turn it to the right using your thumb until the

valve is completely open.

• Now press the piezo ignition (9) immediately.

• Look through the inspection glass (11) to see if the hot glue gun has ignited successfully. If

yes, the heating chamber will be glowing red. The brightness may vary slightly depending

on the level of the gas in the tank and depending on the quality of the gas used.

• DANGER! In case the hot glue gun does not ignite successfully after numerous five

attempts, close the gas supply regulator immediately to stop the gas flow and refer to the

"Troubleshooting" chapter.

Gluing applications

Before gluing

• The surfaces to be glued must be clean, dry and free of grease. Clean the gluing surfaces

before applying the glue if necessary.

• Polished or shiny surfaces should be roughened before gluing.

• Insert a glue stick into the glue port as described above.

• Press the trigger (7) to move the glue stick into the heating chamber.

• Allow the heating chamber and the glue stick to heat up for 2 - 3 minutes until the glue

melts.

• Press the trigger to apply glue to the gluing surface.

After gluing

• After applying glue, bring the workpieces together and press them firmly.

• Use a clamp or similar fixture if required.

• The clamping fixture can be removed after about 5 minutes.

• Allow any surplus glue to cool down completely and subsequently remove it with a knife.

Gluing

Note! Practice before you start working with the glue gun. Carry out trials

on waste material. The correct amount of glue and the feed rate for each

application depend on the size and properties of the materials you wish to

glue and can only be determined by carrying out trials.

6. After nishing work

Note! Risk of damage!

• After completing the work, switch off the hot glue gun and press the

trigger repeatedly to completely use up any residue of the glue stick that

may be present, thus emptying the heating chamber.

• Place the hot glue gun on the integrated stand and allow it to cool

completely.

• Clean the hot glue gun before storage.

• If the hot glue gun is not being used, keep it in a safe, cool, dry and well-ventilated place,

out of the reach of children.

• Store the hot glue gun and accessories in its original packaging or similar suitable

packaging.

7. Storage and transport

8. Maintenance and spare parts

Maintenance and repairs

Cleaning

The product requires very little maintenance.

Repairs should only be carried out by qualified technicians or by an authorised service

centre. Qualified technicians must have relevant training and experience, be familiar with the

design and construction requirements of the product and understand and follow the safety

regulations.

Caution! NEVER immerse the hot glue gun in water.

• Allow the hot glue gun to cool completely before you start cleaning.

• Clean the product with a moist cloth. Never use strong and / or abrasive cleaning agents

or solvents. Allow all the parts to dry completely. Ensure that water does not get into the

product.

Model: PHKPG 150 A1

Device category: Direct pressure butane

Rated power: 128 W

Consumption: approx. 10 g / h

Operating temperature: +10°c – +40°c

Diameter of the glue sticks: 11 mm

9. Troubleshooting

10. Technical specications

Problem Possible cause Solutions, tips

The hot glue gun is not

igniting.

The gas tank is empty. Allow the device to cool and fill the

gas tank.

The gas supply regulator

(2) is not open or not

open sufficiently.

Open the gas supply regulator (or

open further if necessary).

Catalyst is used up. The hot glue gun is provided with

a palladium-loaded catalyst which

allows the gas to burn flamelessly.

The catalyst is designed for long

service life. Once the catalyst is

used up, the device can either be

disposed of or you can get a new

catalyst installed at the service

centre by paying the corresponding

charges.

Disposing of the used device

Instructions for disposal of the gas cartridge

Disposal of packaging

If the product can no longer be used, then all the consumers are required by law to bring the

old device to a separate waste collection point, for example in their community or district,

and not to dispose of it in the household waste. This ensures that the old devices are properly

recycled and negative impact on the environment is avoided.

Do not forcibly open the gas cartridge or burn it after use.

Gas cartridges which are completely empty can be sent to the municipal waste collection

centre or disposed of along with domestic waste.

Gas cartridges which are not completely empty should be disposed of as special waste

according to the waste disposal regulations. Please contact your local municipal authority for

further information.

Dispose of the packaging material according to the type of material and according

to any local regulations.

11. Disposal

Warranty provided by Walter Werkzeuge Salzburg GmbH

Dear customer,

This device comes with a 3 year warranty from the date of purchase. In case of defects in

the product you may be entitled to legal claims against the seller of the product. These legal

claims are not restricted by the following warranty.

Conditions of warranty

The warranty period begins with the date of purchase. Please preserve the original sales

receipt. This document is required as proof of purchase. If a material or fabrication defect

occurs in this product within three years from the date of purchase, the product shall be

12. Warranty

repaired or replaced free of cost at our discretion. Within the three year period the warranty

requires the defective product and the purchase document (sales receipt) to be provided with

a brief written description of where the defect lies and when it occurred.

If the defect is covered by our warranty, the repaired product or a new product shall be

returned to you. A new warranty period does not begin with the repair or exchange of the

product.

Warranty period and legal claims based on defects

The warranty period is not extended by the warranty. This also applies to replaced and

repaired parts. Any damages and defects that may exist at the time of purchase must be

notified immediately after removal from packaging. Any repairs arising after the expiry of the

warranty period are chargeable.

Scope of the warranty

The device has been manufactured according to strict quality guidelines and tested diligently

before delivery. The warranty applies to material or fabrication defects. This warranty does

not cover product parts that are subject to normal wear and tear and therefore can be

considered as parts subject to wear and tear or for the damage to fragile parts, e.g switch,

batteries or those made of glass.

This warranty is void if the product is damaged, not used or maintained properly. All the

instructions provided in the operating manual must be followed exactly for proper use of

the product. The purpose of use and actions which are advised or warned against must

necessarily be avoided.

The product is intended solely for private use and not for professional use. The warranty is

void in case of misuse or improper handling, use of force and changes that have not been

carried out by our authorised service centre.

Processing a warranty case

To ensure quick processing of your issue, please follow the below instructions:

• Please be ready with the sales receipt and the product number (e.g. IAN 12345) as proof

or purchase for all queries.

• You can refer the product number from the type label, , an engraving, on the cover sheet

of your operating instructions (below left) or as sticker on the back or lower side.

• If functional or other defects occur, first call or email the following service department.

• You can then send a product recorded as defective postage free along the the sales

receipt and information about where the defect lies and when it has occurred, to the

service centre address provided to you.

This and many other manuals, product videos and software can be downloaded at www.

lidl-service.com

Service

Walter Tools (GB) Ltd.

E-Mail: ser[email protected]

Tel.: 00800 925 837 88

IAN 285747

Supplier:

Please note that the following address is not a service centre address Please contact the

above-mentioned service centre first.

Walter Werkzeuge Salzburg GmbH

Gewerbeparkstrasse 9

5081 Anif

Austria

IAN 285747

Walter Werkzeuge Salzburg GmbH

Gewerbeparkstrasse 9

5081 Anif, Austria

V. 1.0

Last Information Update:

06/2017

Parkside PHKPG 150 A1 Operating And Safety Instructions Manual

Parkside PHKPG 150 A1 Operating And Safety Instructions Manual

Parkside PHKPG 150 A1 Operating And Safety Instructions Manual

Related papers

Other documents