Haier HI1MK Installation Instructions Manual

Haier

What The World Comes Home To _

Automatic I_ceMaker

Fabricader de Hie_esAutematice

Instaltation InstructiOnSo

Model#

#nstructionsd'insta##atiOno

Modele#

#nstruccionesdeinsta#aci6no

Modelo#

l_portan_ Safety _nstru¢_ions

Warning!

1) To avoid electric shock, which can cause death or severe personal injury,

disconnect the refrigerator from the electrical power before connecting a

water supply line to the refrigerator.

2) Do not place fingers or hand on the automatic ice making mechanism

while the refrigerator is plugged in. This will help protect you from

possible injury. It will also prevent interference with moving parts of the

ejector mechanism and the heating element that releases the cubes.

To avoid property damage:

• Copper tubing is recommended for the water supply line. Water

supply tubing should be 1/4". Plastic is not recommended since it

greatly increases the potential for water leaks.

• Do not install water supply tubing in areas where the temperature

falls below freezing.

• Connect the ice maker to a drinkable water source that is not tied

into a water softening system. Chemicals from the softener may

damage the ice maker, causing it to malfunction.

SuppMies Required for installation

The following items are required to install the ice maker.

a) 1/4 inch copper supply line with shut off valve.

b) 1/4 inch brass compression nut and ferrule (sleeve).

• The copper tubing and shut off valve should be available at your local

hardware or plumbing supply store. Coil enough tubing in the back of the

unit to allow movement for cleaning.

TooMs Required for Installation

Plastic putty knife

Phillips screwdriver

1/4-inch socket wrench or nut driver

Adj usta ble wrench

Needle nose pliers

Power drill with Phillips bit #2

1

Parts }nc}uded

1. Ice Maker with Power Cord

2. Ice Container

3. Plastic Water Supply Tubing

with Plastic Nut

4. Self-Tapping Screws (Qty-2)

5. Pan Head Screws (Qty-2)

6. Leveling Bracket Screw (Qty-1)

7. Leveling Bracket (Qty-1)

8. Steel Clamp (Qty-1)

9. Plastic Clamp (Qty-2)

10. Water Valve (Qty-1)

11. Water Inlet Tube (Qty-1)

12. Hex-Head Screw for

Water Line Clamp (Qty-1)

13. Owner's Manual &

Installation Instructions

G

©

®

_nstaHation Instruotions

1. Unplug the refrigerator from the power outlet and move it out for easier

access.

2. Remove the ice tray rack by unscrewing the Phillips head screws.

3. Remove the freezer shelf by pushing the shelf to your left until the right

side is free from the holes. Lift the shelf gently and remove.

4. There are 2 plugs on the left side wall and one on the back wall in the

freezer compartment that must be removed. The holes are used to

mount the ice maker and to pull through the water inlet tube.

(See fig. # 1 )

(Figure 1)

5.

6.

7.

3

Remove the electrical plug cover that is mounted on the freezer back

wall.

Unscrew the rear access panel that covers the compressor compartment.

(See fig. # 2) nterior

Condenser

Water Filling

Tube Gromme[

(Figure 2)

I Rear Acc:ssPane :

Pull out the water fill tube grommet from the rear of the refrigerator.

(See fig. # 2)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i i i i ! !!

8,

Insert the supplied fill tube completely into the grommet. Reinstall the

grommet with the filling tube through the refrigerator body. (Rotate

while inserting the tube) Firmly reinstall the grommet in the rear of the

refrigerator. (See fig # 3)

(Figure 3)

g,

Install the supplied leveling bracket with the supplied leveling bracket

screw to the screw hole on the bottom of the icemaker. Use the screw

hole that is near the power cord. (See fig. # 4)

Note: Do not tighten all the way

(Figure 4)

10. Take the 2 pan head screws and screw them half way into the 2 holes

on the left wall of the freezer compartment.

11. Insert the electrical power cord plug of the icemaker into the power

socket on the rear wall of the freezer compartment. (Seefig. # 5)

(Figure 5)

i

12. Align and fit the fill tube into the filling cup on the ice maker. Now

hang and tighten the ice maker on the 2 side wall screws. (See fig. #6)

Note: The fill tube may need to be cut for length adjustment.

(Figure 6)

13. Reinstall the electrical plug cover located on the rear wall.

14. Level the ice maker by pushing the leveling bracket against the freezer

wall. Now tighten the leveling screw.

15. Reinstall the freezer shelf and place the ice container under the ice

maker. (See fig. #7)

(Figure 7)

16. Raise the wire auto shut off arm on the ice maker until the full

installation is completed.

Water Valve and Tubing _nstaHation

1. Locate the wire harness that is placed on the right side of the

compressor compartment, (Factory preinstalled on the refrigerator)

(See fig. #8)

(Figure 8)

2. Plug the harness to the supplied water valve.

3. Remove the plastic cap from the bottom of the grommet. Insert the

plastic water supply tubing into the inlet as far as it can go. (See fig # 9)

(Figure 9)

4. Insert the other end of the plastic water tubing into the bottom of the

water valve. Tighten the plastic nut, while pushing the tube inside the

valve. (See fig # 10)

(Figure 1O)

5. Using a power drill with a Phillips-head bit, drive in the 2 supplied self

tapping screws to attach the water valve to the right side of the

refrigerator. (See fig. # 11)

(Figure 11)

Water SuppMy Connection

This water supply installation is not warranted by the refrigerator

or icemaker manufacturer, Follow these instructions carefully to

minimize the risk of expensive water damage.

Supplies Required for Installation:

• Access to a household cold water line with water pressure between

20psi. and 120psi.

• A water supply line made of 1/4-inch OD, copper tubing. To determine

the length of the copper tubing needed, you will need to measure the

distance from the ice maker inlet valve at the back of the refrigerator to

your cold water pipe. Then add approximately 7 feet, so the refrigerator

can be moved out for service.

• A shutoff valve to connect the water supply line to your household

water system.

Note: Do Not use a self-piercing type shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply

line to the ice maker inlet valve.

1. Turn off the water supply at the shut off valve.

2. Remove the plastic cap from the water valve inlet.

3. Insert the brass compression nut and the ferrule (sleeve) onto the end of

the copper water line as shown in the picture.

4.Nowpushthe water supply line into the water valve inlet as far as it will

go. Slide the ferrule (sleeve) into the valve inlet and finger tighten the

compression nut onto valve. Tighten another half-turn with a wrench. Be

careful not to over tighten. Now, screw rear access panel that covers

compressor com )artment back in place. (See fig. # 12)

(Figure 12) ..........

Power cord Plastic water tubing

ii_;!i!i!i!

Coper water line

5. With the supplied steel clamp and hex head screw, secure the water

supply line to the rear panel of the refrigerator.

9

6.Coiltheexcesswatersupplylinebehindrefrigerator,asshownin

fig.# 12andarrangethecoilssotheydonotvibrateorwearagainst

othersurfaces.

7.TurnONthewatersupplyattheshutoffvalveandtightenany

connectionsthatleak.

8.Reconnectthe refrigerator to the power supply.

9. To turn the icemaker ON, lower the auto shut-off arm.

Important: It takes approximately 24 hours for the ice maker to produce

ice. New plumbing may cause ice discoloration and poor

flavor. Discard ice made in the first 24 hours.

Automatic Maker Tips

Remember that the water quality determines your ice quality. Do not

connect the ice maker to water that is softened. Chemicals from a

malfunctioning softener can damage the icemaker.

To stop the ice maker, lift the wire arm until it clicks and locks in the OFF

(raised) position. The ice maker turns OFF automatically when the ice

container is full. If your model has an adjustable freezer shelf, place the

shelf so that when the ice container is full, the

ice will hit the wire signal arm.

Ice Maker Tips:

• Ice stored too long may develop an odd

flavor. Empty the container and make sure

the wire arm is in its ON (lowered)

position. The ice maker will then produce ice.

• Keep the wire arm in OFF position until the

refrigerator is connected to the water supply or whenever the water

supply is turned OFF.

• The following sounds are normal when the ice maker is operating.

• Running motor

• Ice dropping into ice container

• Running water

• Water valve opening or closing

CAUTION:

• Do Not wash the ice container in your dishwasher.

• Stop the ice maker when cleaning the freezer or when leaving for short

vacations.

• If the ice maker has to be turned OFF for a long period of time,

turn the water supply valve to the closed position. 10

In-Home Service

What is covered and for how

long?

This warranty covers all defects in

workmanship or materials of the

automatic ice maker for a period of:

12 months labor

12 months parts

The warranty commences on the date

the item was purchased and the original

purchase receipt must be presented to

the authorized service center before

warranty repairs are rendered.

What is covered.

1. The mechanical and electrical parts,

which serve as a functional, purpose

of this kit for a period of 12 months.

What will be done?

1, We will repair or replace, at our dis-

cretion any mechanical or electrical

part which proves to be defective in

normal usage during the warranty

period so specified.

2. There will be no charge to the

purchaser for parts and labor on any

covered items during the initial 12

month period.

3. Contact your nearest authorized

service center. For the name of the

nearest service center please call

1-877-337-3639

THIS WARRANTY COVERS

WITHIN THE CONTINENTAL UNIT-

ED STATES, PUERTO RICO AND

CANADA. IT DOES NOT COVER

THE FOLLOWING:

Damages from improper installation.

Damages in shipping.

Defects other than manufacturing.

Damage from misuse, abuse, accident,

alteration, lack of proper care and

maintenance or incorrect current or

voltage.

Damage from other than household use.

11

Damage from service by other than an

authorized dealer or service center.

Transportation and shipping.

• Improper installation

If you have an installation problem,

contact your dealer or installer.

You are responsible for providing ade-

quate electrical, plumbing and other

connecting facilities, including the water

line to the ice maker and the water line

installation.

• Replacement of house fuses or resetting

of circuit breakers.

• Failure of the product if it is used for

other than its intended purpose or used

commercially.

• Damage to product caused by

accident, fire, floods or Acts of God,

WARRANTOR IS NOT RESPONSIBLE

FOR CONSEOUENTIAL DAMAGES.

THIS LIMITED WARRANTY IS GIVEN IN

LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR, INCLUDING THE

WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR

PURPOSE.

The remedy provided in this warranty is

exclusive and is granted in lieu of all

other remedies,

This warranty does not cover incidental

or consequential damages, so the above

limitations may not apply to you. Some

States do not allow limitations on how

long an implied warranty lasts, so the

above limitations may not apply to you,

This warranty gives you specific legal

rights, and you may have other rights,

which vary, from state to state.

Haler America

New York, NY 10018

Consignes de seourite importantes

Avertissement!

1) Pour eviter tout risque d'electrocution pouvant entrainer des blessures

graves voir la mort, debranchez le cordon d'alirnentation du refrigerateur

de la source de courant avant de raccorder la conduite d'alirnentation

d'eau au refrigerateur.

2) Ne placez pas les doigts ou les mains sur le rnecanisrne de la machine

glace autornatique pendant que le refrigerateur est branche. Vous eviterez

ainsi de vous blesser accidentellernent. Cela evitera egalernent toute inter-

ference avec les pieces mobiles du rnecanisrne d'ejection et de I'elernent

chauffant qui libere les gla(i:ons.

Pour eviter des deg_ts materiels:

• II est recornrnande d'utiliser une conduite en cuivre pour la tuyau-

terie d'alirnentation d'eau. La conduite doit rnesurer 1/4 po. (6

rnrn) de diarnetre. II est deconseille d'utiliser un tuyau en plastique

car cela augrnentera les risques de fuites potentielles.

• N'installez pas la conduite d'alirnentation d'eau dans les endroits

ore3il risque de geler.

• Raccordez la machine a glace a une source d'eau potable qui

n'est pas raccordee a un adoucisseur d'eau. Les produits chirn-

iques presents dans un adoucisseur d'eau risquent d'endornrnager

la machine a glace et elle risque de tornber en panne.

Accessoires requis pour I instaIIation

Les amides suivants sont necessaires afin d'instaIIerla machine a glace.

a) Une conduite d'alimentation en cuivre de 1/4 po. (6 ram) de diametre

avec un robinet d'arret.

b) Un ecrou de compression en laiton de 1/4 po. (6 mm) de diametre et un

raccord de branchement (manchon).

• Vous pouvez vous procurer la conduite en cuivre et le robinet de d'arret

aupres de votre quincaillier ou d'un magasin de materiel de plomberie.

Enroulez suffisamment de tuyau a I'arriere de la machine afin de pouvoir y

acceder pour le nettoyage.

OutHs r÷quis pour _'instaHation

Couteau a mastic en plastique

Tournevis Phillips (cruciforme)

Cle a tube d'1/4 po.( 6 mm) ou tourne-ecrou

Cle reglable

Pinces a becs fins

Perceuse electrique avec foret Phillips #2

Pie¢÷s foumies

1. Machine a glace avec cordon

d'alimentation

2. Recipient a glace

3. Tuyau d'alimentation d'eau en

plastique avec ecrou plastique

4, Vis autotaraudeuses (2)

5. Visa cylindrique bombee (2)

6. Vis de support pour raise

niveau (1)

7. Support de mise a niveau (1)

8. Collier en acier (1)

9. Collier en plastique (2)

10, Robinet d'eau (1)

11. Tube d'arrivee d'eau (1)

12. Visa tete hexagonale pour col-

lier de la conduite d'eau (1)

13. Manuel d'utilisation et instruc-

tions d'installation

©

®

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii ii i

_nstru¢_ions d_instaHation

1. Debranchez le rdrigerateur de la prise de courant electrique et sortez-le

afin d'y acceder plus facilement.

2. Retirez la clayette a glace en devissant les vis cruciformes Phillips.

3. Retirez la clayette du congelateur en poussant la clayette vers la gauche

jusqu'a ce que le c6te droit se soit degage des trous. Soulevez douce-

ment la clayette et retirez-la.

4. II existe deux prises de branchement dans la cloison laterale gauche et

une prise sur la cloison arriere du compartiment congelateur dont les

capuchons de protection devront etre retires. Les trous servent a fixer la

machine a glace et pour introduire le tuyau d'arrivee d'eau

(voir la figure 1).

(Figure 1)

5. Retirez le cache de protection de la prise electrique qui se trouve sur la

cloison arriere du congelateur.

6.Devissezlepanneaud'accesarrierequiprotegelecompartimentdu

compresseur(voirlafigure2).

(Figure 2)

7. Retirez le passe-fils du tuyau de remplissage d'eau de I'arriere du

refrigerateur (voir la figure 2).

8.

Introduisez completement le tuyau de remplissage fourni dans le passe-

fils. Replacez le passe-fils avec le tuyau de remplissage dans I'habillage

du refrigerateur. (Tournez tout en introduisant le tube). Replacez ferme-

ment le passe-fils a I'arriere du refrigerateur (voir la figure 3).

(Figure 3)

g,

Montez le support de mise a niveau a I'aide de la vis fournie en la

pla_;:ant dans le trou de la partie inferieure (fond) de la machine

glace. Utilisez le trou a vis qui se trouve a proximite du cordon d'ali-

mentation (voir la figure 4).

Remarque: Ne pas serrez completement.

(Figure 4)

10. Prenez les deux visa tete bombees et vissez-les a moitie dans les deux

trous de la cloison gauche du compartiment congelateur.

11. Introduisez la fiche du cordon d'alimentation electrique de la machine

glace dans la prise de courant de la cloison arriere du compartiment

congelateur (voir la figure 5).

(Figure 5)

12. Alignez et placez le tuyau de remplissage dans la coupelle de remplis-

sage de la machine a glace. A present, accrochez la machine a glace

sur les deux vis des cloisons laterales et serrez-les (voir la figure 6).

Remarque: Vous devrez peut-etre couper le tuyau de remplissage

afin de regler la Iongueur.

(Figure 6)

13. Replacez le cache de protection de la prise de courant electrique de la

cloison arriere.

14. Mettez la machine a glace a niveau en pressant le support de mise

niveau contre la cloison du congelateur. Serrez a present la vis de mise

niveau.

15. Replacez la clayette du congelateur et placez le recipient a glace sous

la machine a glace (voir la figure 7).

(Figure 7)

16. Apres avoir completement termine I'installation, relevez le bras d'arret

automatique de la machine a glace.

_nstaHation du robin÷_ d_eau ÷t de _a tuyauterie

1. Recherchez le faisceau de cablage situe sur le cote droit du comparti-

ment du compresseur. (Monte sur le refrigerateur en usine).

(voir la figure 8)

(Figure 8)

2. Branchez la faisceau de cablage sur la valve de debit d'eau fournie.

3. Retirez le capuchon en plastique du bas du passe-ills. Introduisez le tuyau

d'arrivee d'eau en plastique dans I'entree aussi loin que possible

(voir la figure 9).

(Figure 9)

Page is loading ...

Haier HI1MK Installation Instructions Manual

Haier HI1MK Installation Instructions Manual

in other languages

Related papers

Other documents