Southern Enterprises HZ106300TX Assembly Instructions Manual

HZ106300TX

Hagan Storage Cabinet

Assembly Instructions

PO:13411

For assistance with assembly, contact.

Southern Enterprises Inc.

Customer Service 1-800-633-5096

[email protected]

www.seidal.com

Top supports up to 40 lb.

Per adjustable shelf supports up to 20 lb.

Fixed bottom shelf supports up to 30 lb.

HZ106300TX

HAGAN STORAGE CABINET

Parts List

Please review all parts and hardware before disposing of any packaging.

Call Customer Service if missing hardware.

Carefully study the diagrams below.

You may receive extra hardware with your unit.

1 1PC

Top Panel

2 1PC

Left Panel

3 1PC

Right Panel

4 1PC

Back Panel

5 1PC

Bottom Panel

6 2PCS

Shelf

7 1PC

Left Door

8 1PC

Right Door

9 1PC

Upper Leg

10 1PC

Lower Leg

A 1PC

Magnet

B 4PCS

Screw 3x15mm

C 8PCS

Wood Dowel

D 6PCS

Cam Bolt

E 6PCS

Cam Lock

F 10PCS

Screw 8x1-1/2”L

G 1PC

Bolt 3/16”x1/2”L

H 4PCS

End Cap

I 2PCS

Iron Chip

J 2PCS

Screw 3x8mm

K 4PCS

Door Hinge

L 16PCS

Screw 6x1/2”L

M 8PCS

Bracket

N 4PCS

L Metal Chip

O 2PCS

Screw 4x12mm

P 2PCS

Wall Anchor

Q 2PCS

Screw 4x1”L

R 2PCS

Plastic Strap

Assembly Tool Required

No.2 Phillips Screwdriver

Care and Cleaning Instructions:

Before using, wipe with a clean, dry cloth.

Avoid rubbing or scratching the surface with

rough or abrasive objects.

For replacement parts or questions, please

Call Customer Service at 1-800-633-5096.

HZ106300TX

HAGAN STORAGE CABINET

Assembly Instructions

Figure 1

Step 1

:

Unit assembly should begin

with parts turned upside down

for Step 1.

Attach magnet (A) into the

pre-drilled holes on Top Panel

(1) using Screws (B) as

shown.

Attach Left Panel (2) and

Right Panel (3) to Top Panel

(1) using Wood Dowels (C)

and Cam Bolts (D) as shown.

Figure 2

Step 2

:

Fix Left Panel (2) and Right

Panel (3) to Top Panel (1)

using Cam Locks (E) as

shown.

Figure 3

Step 3:

Slide Back Panel (4) along the

grooves of Left Panel (2) and

Right Panel (3).

Then, attach Wood Dowels (C)

to Left Panel (2) and Right

Panel (3) as shown.

Figure 4

Step 4:

Attach Bottom Panel (5) to the

assembled unit using Screws

(F) as shown.

Figure 5

Step 5:

Attach Lower Leg (10) to Upper

Leg (9) using Bolt (G). Then,

aim at the pre-drilled holes on

the Bottom Panel (5) to attach

the assembled Leg Frame to

Bottom Panel (5) using Screws

(F) as shown.

Attach End Caps (H) to Legs

(9) and (10) as shown.

Figure 6

Step 6:

Attach Door Hinges (K) to Left

Door (7) and Right Door (8)

using Screws (L). Then, attach

Iron Chip (I) using Screws (J)

as shown.

Please make sure the side

of the Iron Chips (I) with tips

are facing in towards the

Doors (7/8) while attaching.

L

J

I

K

8

K

7

7,

8

I

J

Figure 7

Step 7:

Turn the assembled unit

upright.

Attach Doors (7) and (8)

w/Door Hinges (K) to the

grooves of Left Panel (2) and

Right Panel (3) using Screws

(L) as shown.

Figure 8

Step 8:

Insert Brackets (M) into the

holes on the insides of Left

Panel (2) and Right Panel (3)

and make sure the positions

of the Brackets (M) are even.

Insert Shelves (5) following the

arrow direction and make sure

Brackets (M) hold Shelves (5)

stably.

Your storage cabinet is now

complete.

8

7

L

K

3

2

Anti-tipping

Hardware Must be

Used for this

product to avoid

tipping and injury

Aim at the pre-drilled holes on

the back of Left Panel (2) and

Right Panel (3) to attach L

Metal Chip (N) using Screws

(O) as shown.

Tip: Screw must be directly

mounted into a wall stud. Wall

anchor is not needed when

mounting into a wall stud.

Find an ideal location on the

wall and mark the location of

the center of each mounting

hole.

Using a power drill and a

3/16″drill bit, drill two 3/16″

holes on the wall.

Note: Make sure not to drill into

electrical wiring or plumbing

pipes.

Insert Wall Anchors (P) into the

two 3/16″ holes. Make sure that

the wall anchors are flush with

the wall.

Tip: It may be necessary to use

a hammer to gently tap the

anchors into place.

FLOOR

31.25

”

27.

5

”

Attach

L Metal Chip (N) to Wall

Anchor (P) u

sing Phillips Head

Screws (Q) and the Phillips

Screwdriver as shown.

Attach Plastic Strap (R) to L

Metal Chip (N) on the wall and

cabinet as shown.

(Q)

Please immediately examine this product carefully. Any request for missing parts or damage replacement

must be received within 90 days of your receipt of the product. Replacement, if available, will be honored

within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend

modifying product(s) and we are not responsible for any damages due to product modification(s).

If

damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to

provide parts or replacement merchandise.

Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri

Central time if you have product issues or email us at [email protected]. Please ask for customer service

representative for issues involving damages or replacement parts. Please ask for technical assistance

representative for any issues with product and assembly/construction.

Please contact the retailer that you purchased from for returns.

Customer Information

Name

Address

City/State/Zip Code

Phone Number

Please indicate where you purchased this item: Store/Website/Catalog

Please indicate color/size/style number:

Style No Parts Letter Parts Description Quantity Needed

Customer Service 1-800-633-5096

service@seidal.com

Southern Enterprises, Inc.

600 Freeport Parkway, Suite 200

Coppell, Texas 75019

Parts Replacement Form

Southern Enterprises HZ106300TX Assembly Instructions Manual

Southern Enterprises HZ106300TX Assembly Instructions Manual

Related papers

Other documents