D-Link Storage User manual

1

D-Link iSCSI IP SAN storage

10GbE iSCSI to SATA II / SAS

RAID IP SAN storage

DSN-6410 & DSN-6420

User Manual

Version 1.0

2

Preface

Copyright

be reproduced or transmitted without written permission from D-Link corporation.

Trademarks

All products and trade names used in this manual are trademarks or registered trademarks

of their respective companies.

About this manual

This manual is the introduction of D-Link DSN-64x0 IP SAN storage and it aims to help

users know the operations of the disk array system easily. Information contained in this

manual has been reviewed for accuracy, but not for product warranty because of the

various environments / OS / settings. Information and specification herein are subject to

change without notice. For any update information, please visit www.dlink.com.

Model comparison

DSN-6400 series adopt 2U12 form factor for all models. DSN-64x0 IP SAN storages

stand for the following models.

DSN-6420: Dual controllers.

DSN-6410: Single controller, can be upgradable to dual mode.

The dual controller specific functions such as dual-active, cache mirroring, flexible RG

ownership management, management port seamless take-over, no system down time,

and etc are not available in DSN-6410.

Caution

Do not attempt to service, chan

g

e, disassemble or up

g

rade the equipment’s

components by yourself. Doing so may violate your warranty and expose

you to electric shock. Refer all servicin

g

to authorized service personnel.

Please always follow the instructions in this user’s manual.

3

Table of Contents

Chapter 1 Overview..................................................................6

1.1 Features.........................................................................................6

1.1.1 Highlights.................................................................................................................6

1.2 RAID concepts...............................................................................7

1.2.1 Terminology.............................................................................................................8

1.2.2 RAID levels.............................................................................................................10

1.2.3 Volume relationship................................................................................................11

1.3 iSCSI concepts.............................................................................12

1.4 IP SAN storage specifications ......................................................13

1.4.1 Technical specifications..........................................................................................13

1.4.2 FCC and CE statements..........................................................................................16

Chapter 2 Installation............................................................19

2.1 Package contents.........................................................................19

2.2 Before installation........................................................................19

2.3 Enclosure .....................................................................................19

2.3.1 Front view..............................................................................................................19

2.3.2 Front LED lights .....................................................................................................20

2.3.3 Install drives...........................................................................................................21

2.3.4 Rear view...............................................................................................................22

2.4 Install battery backup module .....................................................25

2.5 Deployment..................................................................................26

Chapter 3 Quick setup............................................................29

3.1 Management interfaces ...............................................................29

3.1.1 Serial console.........................................................................................................29

3.1.2 Remote control.......................................................................................................29

3.1.3 Web UI...................................................................................................................30

3.2 How to use the system quickly....................................................32

3.2.1 Quick installation....................................................................................................32

3.2.2 Volume creation wizard..........................................................................................35

Chapter 4 Configuration ........................................................38

4.1 Web UI management interface hierarchy....................................38

4.2 System configuration...................................................................39

4.2.1 System setting .......................................................................................................39

4.2.2 Network setting......................................................................................................40

4.2.3 Login setting ..........................................................................................................41

4.2.4 Mail setting.............................................................................................................42

4.2.5 Notification setting.................................................................................................43

4.3 iSCSI configuration ......................................................................45

4.3.1 NIC.........................................................................................................................45

4.3.2 Entity property.......................................................................................................48

4.3.3 Node ......................................................................................................................48

4.3.4 Session...................................................................................................................51

4.3.5 CHAP account ........................................................................................................52

4.4 Volume configuration...................................................................53

4

4.4.1

 Physical disk...........................................................................................................54

4.4.2 RAID group............................................................................................................57

4.4.3 Virtual disk.............................................................................................................60

4.4.4 Snapshot................................................................................................................65

4.4.5 Logical unit.............................................................................................................68

4.4.6 Example.................................................................................................................69

4.5 Enclosure management ...............................................................74

4.5.1 Hardware monitor..................................................................................................75

4.5.2 UPS ........................................................................................................................76

4.5.3 SES.........................................................................................................................78

4.5.4 Hard drive S.M.A.R.T. ............................................................................................78

4.6 System maintenance....................................................................79

4.6.1 System information................................................................................................79

4.6.2 Event log................................................................................................................80

4.6.3 Upgrade.................................................................................................................82

4.6.4 Firmware synchronization ......................................................................................82

4.6.5 Reset to factory default..........................................................................................83

4.6.6 Import and export..................................................................................................83

4.6.7 Reboot and shutdown............................................................................................84

4.7 Home/Logout/Mute......................................................................84

4.7.1 Home .....................................................................................................................84

4.7.2 Logout....................................................................................................................84

4.7.3 Mute.......................................................................................................................85

Chapter 5 Advanced operations...........................................86

5.1 Volume rebuild.............................................................................86

5.2 RG migration................................................................................88

5.3 VD extension................................................................................89

5.4 Snapshot......................................................................................89

5.4.1 Create snapshot volume.........................................................................................90

5.4.2 Auto snapshot........................................................................................................91

5.4.3 Rollback..................................................................................................................92

5.4.4 Snapshot constraint ...............................................................................................93

5.5 Disk roaming................................................................................95

5.6 VD clone ......................................................................................95

5.7 SAS JBOD expansion..................................................................103

5.7.1 Connecting JBOD .................................................................................................103

5.7.2 Upgrade firmware of JBOD ..................................................................................105

5.8 MPIO and MC/S .........................................................................106

5.9 Trunking and LACP ....................................................................108

5.10 Dual controllers (only for DSN-6420).........................................109

5.10.1 Perform I/O..........................................................................................................109

5.10.2 Ownership............................................................................................................110

5.10.3 Controller status...................................................................................................111

5.11 Replication.................................................................................112

5.12 VLAN..........................................................................................122

Chapter 6 Troubleshooting .................................................125

6.1 System buzzer............................................................................125

5

6.2 Event notifications .....................................................................125

Appendix 133

A. Certification list..........................................................................133

B. Microsoft iSCSI initiator..............................................................136

C. From Single controller to Dual Controller ……………………. 142

6

Chapter 1 Overview

1.1 Features

D-LINK DSN-6000 series IP SAN storage provides non-stop service with a high degree of

fault tolerance by using D-LINK RAID technology and advanced array management

features.

DSN-6410/6420 IP SAN storage connects to the host system by iSCSI interface. It can

be configured to numerous RAID level. The IP SAN storage provides reliable data

protection for servers by using RAID 6. The RAID 6 allows two HDD failures without any

impact on the existing data. Data can be recovered from the existing data and parity

drives. (Data can be recovered from the rest drives.)

Figure 1.1.1 (DSN-6410/6420)

Snapshot-on-the-box is a fully usable copy of a defined collection of data that contains

an image of the data as it appeared at the point in time, which means a point-in-time data

replication. It provides consistent and instant copies of data volumes without any system

downtime. Snapshot-on-the-box can keep up to 32 snapshots for one logical volume.

Rollback feature is provided for restoring the previous-snapshot data easily while

continuously using the volume for further data access. The data access which includes

read / write is working as usual without any impact to end users. The "on-the-box" implies

that it does not require any proprietary agents installed at host side. The snapshot is taken

at target side. It will not consume any host CPU time thus the server is dedicated to the

specific or other application. The snapshot copies can be taken manually or by schedule

every hour or every day, depends on the modification.

D-LINK IP SAN storage is the most cost-effective disk array system with completely

integrated high-performance and data-protection capabilities which meet or exceed the

highest industry standards, and the best data solution for small / medium business

(SMB) and enterprise users.

1.1.1 Highlights

7

 D-LINK DSN-6410/6420 feature highlights

Host

Interface

4 x 10GbE iSCSI ports (DSN-6420)

2 x 10GbE iSCSI ports (DSN-6410)

Drive

Interface

12 x SAS or SATA II

RAID

Controllers

Dual-active RAID controllers (DSN-6420)

Single controller, but can be upgradable to dual (DSN-6410)

Scalability SAS JBOD expansion port

Green Auto disk spin-down

Advanced cooling

RAID Level RAID 0, 1, 0+1, 3, 5, 6, 10, 30, 50, 60 and JBOD

N-way mirror

Compatibility Support multiple OSes, applications, 10GbE NIC, 10GbE iSCSI

HBA, and etc.

Virtualization VMWare, Hyper-V, Citrix

Data

Protection

Snapshot (Read only and Writeable), Storage base Replication

Connection

Availability

Load balancing and failover support on the 4 x 10GbE iSCSI

ports

Dimension

(W x D x H)

442.8 x 500.6 x 88.0 (mm)

Power

Supply

2 x 500W PSU

Cache

Protection

Hot pluggable battery backup module

Fan Redundant

1.2 RAID concepts

8

RAID is the abbreviation of “Redundant Array of Independent Disks”. The basic idea of

RAID is to combine multiple drives together to form one large logical drive. This RAID

drive obtains performance, capacity and reliability than a single drive. The operating

system detects the RAID drive as a single storage device.

1.2.1 Terminology

The document uses the following terms:

 Part 1: Common

RAID Redundant Array of Independent Disks. There are different

RAID levels with different degree of data protection, data

availability, and performance to host environment.

PD The Physical Disk belongs to the member disk of one specific

RAID group.

RG Raid Group. A collection of removable media. One RG consists

of a set of VDs and owns one RAID level attribute.

VD Virtual Disk. Each RD could be divided into several VDs. The VDs

from one RG have the same RAID level, but may have different

volume capacity.

LUN Logical Unit Number. A logical unit number (LUN) is a unique

identifier which enables it to differentiate among separate

devices (each one is a logical unit).

GUI Graphic User Interface.

RAID cell

When creating a RAID group with a compound RAID level, such as 10,

30, 50 and 60, this field indicates the number of subgroups in the RAID

group. For example, 8 disks can be grouped into a RAID group of RAID

10 with 2 cells, 4 cells. In the 2-cell case, PD {0, 1, 2, 3} forms one RAID

1 subgroup and PD {4, 5, 6, 7} forms another RAID 1 subgroup. In the 4-

cells, the 4 subgroups are PD {0, 1}, PD {2, 3}, PD {4, 5} and PD {6,7}.

WT Write-Through cache-write policy. A caching technique in which

the completion of a write request is not signaled until data is

safely stored in non-volatile media. Each data is synchronized in

both data cache and accessed physical disks.

WB Write-Back cache-write policy. A caching technique in which the

completion of a write request is signaled as soon as the data is

9

in cache and actual writing to non-volatile media occurs at a

later time. It speeds up system write performance but needs to

bear the risk where data may be inconsistent between data

cache and the physical disks in one short time interval.

RO Set the volume to be Read-Only.

DS Dedicated Spare disks. The spare disks are only used by one

specific RG. Others could not use these dedicated spare disks for

any rebuilding purpose.

GS Global Spare disks. GS is shared for rebuilding purpose. If some

RGs need to use the global spare disks for rebuilding, they could

get the spare disks out from the common spare disks pool for

such requirement.

DG DeGraded mode. Not all of the array’s member disks are

functioning, but the array is able to respond to application read

and write requests to its virtual disks.

SCSI Small Computer Systems Interface.

SAS Serial Attached SCSI.

S.M.A.R.T. Self-Monitoring Analysis and Reporting Technology.

WWN World Wide Name.

HBA Host Bus Adapter.

SES SCSI Enclosure Services.

NIC Network Interface Card.

BBM Battery Backup Module

 Part 2: iSCSI

iSCSI Internet Small Computer Systems Interface.

LACP Link Aggregation Control Protocol.

MPIO Multi-Path Input/Output.

MC/S Multiple Connections per Session

10

MTU Maximum Transmission Unit.

CHAP

Challenge Handshake Authentication Protocol. An optional

security mechanism to control access to an iSCSI storage system

over the iSCSI data ports.

iSNS Internet Storage Name Service.

 Part 3: Dual controller

SBB Storage Bridge Bay. The objective of the Storage Bridge Bay

Working Group (SBB) is to create a specification that defines

mechanical, electrical and low-level enclosure management

requirements for an enclosure controller slot that will support a

variety of storage controllers from a variety of independent

hardware vendors (“IHVs”) and system vendors.

 Part 4: 10GbE

SFP+ Small Form-factor Pluggable is a compact, hot-pluggable

transceiver used for both Fibre Channel and 10GbE.

CX4 10GBASE-CX4, a copper based 10 Gigabit Ethernet PHY.

1.2.2 RAID levels

There are different RAID levels with different degree of data protection, data availability,

and performance to host environment. The description of RAID levels are on the following:

RAID 0 Disk striping. RAID 0 needs at least one hard drive.

RAID 1 Disk mirroring over two disks. RAID 1 needs at least two hard drives.

N-way mirror Extension to RAID 1 level. It has N copies of the disk.

RAID 3 Striping with parity on the dedicated disk. RAID 3 needs at least three

hard drives.

RAID 5 Striping with interspersed parity over the member disks. RAID 3

needs at least three hard drives.

RAID 6 2-dimensional parity protection over the member disks. RAID 6 needs

at least four hard drives.

RAID 0+1 Mirroring of the member RAID 0 volumes. RAID 0+1 needs at least

11

four hard drives.

RAID 10 Striping over the member RAID 1 volumes. RAID 10 needs at least

four hard drives.

RAID 30 Striping over the member RAID 3 volumes. RAID 30 needs at least six

hard drives.

RAID 50 Striping over the member RAID 5 volumes. RAID 50 needs at least six

hard drives.

RAID 60 Striping over the member RAID 6 volumes. RAID 60 needs at least

eight hard drives.

JBOD The abbreviation of “Just a Bunch Of Disks”. JBOD needs at least

one hard drive.

1.2.3 Volume relationship

The below graphic is the volume structure which D-LINK has designed. It describes the

relationship of RAID components. One RG (RAID group) consists of a set of VDs (Virtual

Disk) and owns one RAID level attribute. Each RG can be divided into several VDs. The

VDs in one RG share the same RAID level, but may have different volume capacity. All

VDs share the CV (Cache Volume) to execute the data transaction. LUN (Logical Unit

Number) is a unique identifier, in which users can access through SCSI commands.

Figure 1.2.3.1

RG

PD 2 PD 3 DS PD 1

VD 1 VD 2

Snapshot

VD

RAM

Cache Volume

+

LUN 1

LUN 2

LUN 3

+

12

1.3 iSCSI concepts

iSCSI (Internet SCSI) is a protocol which encapsulates SCSI (Small Computer System

Interface) commands and data in TCP/IP packets for linking storage devices with servers

over common IP infrastructures. iSCSI provides high performance SANs over standard IP

networks like LAN, WAN or the Internet.

IP SANs are true SANs (Storage Area Networks) which allow several servers to attach to

an infinite number of storage volumes by using iSCSI over TCP/IP networks. IP SANs can

scale the storage capacity with any type and brand of storage system. In addition, it can

be used by any type of network (Ethernet, Fast Ethernet, Gigabit Ethernet, and 10 Gigabit

Ethernet) and combination of operating systems (Microsoft Windows, Linux, Solaris, Mac,

etc.) within the SAN network. IP-SANs also include mechanisms for security, data

replication, multi-path and high availability.

Storage protocol, such as iSCSI, has “two ends” in the connection. These ends are initiator

and target. In iSCSI, we call them iSCSI initiator and iSCSI target. The iSCSI initiator

requests or initiates any iSCSI communication. It requests all SCSI operations like read or

write. An initiator is usually located on the host side (either an iSCSI HBA or iSCSI SW

initiator).

The target is the storage device itself or an appliance which controls and serves volumes

or virtual volumes. The target is the device which performs SCSI command or bridge to an

attached storage device.

Figure 1.3.1

The host side needs an iSCSI initiator. The initiator is a driver which handles the SCSI

traffic over iSCSI. The initiator can be software or hardware (HBA). Please refer to the

certification list of iSCSI HBA(s) in Appendix A. OS native initiators or other software

initiators use standard TCP/IP stack and Ethernet hardware, while iSCSI HBA(s) use their

own iSCSI and TCP/IP stacks on board.

iSCSI device 1

(target)

Host 1

(initiator)

NI

C

IP SAN

Host 2

(initiator)

iSCSI

HBA

iSCSI device 2

(target)

13

Hardware iSCSI HBA(s) provide its own initiator tool. Please refer to the vendors’ HBA user

manual. Microsoft, Linux, Solaris and Mac provide iSCSI initiator driver. Please contact D-

LINK for the latest certification list. Below are the available links:

1. Link to download the Microsoft iSCSI software initiator:

http://www.microsoft.com/downloads/details.aspx?FamilyID=12cb3c1a-15d6-4585-

b385-befd1319f825&DisplayLang=en

2. In current Linux distributions, OS built-in iSCSI initiators are usually available. For

different kernels, there are different iSCSI drivers. Please check Appendix A for iSCSI

initiator certification list. If user needs the latest Linux iSCSI initiator, please visit

Open-iSCSI project for most update information. Linux-iSCSI (sfnet) and Open-iSCSI

projects merged in April 11, 2005.

Open-iSCSI website: http://www.open-iscsi.org/

Open-iSCSI README: http://www.open-iscsi.org/docs/README

Features: http://www.open-iscsi.org/cgi-bin/wiki.pl/Roadmap

Support Kernels:

http://www.open-iscsi.org/cgi-bin/wiki.pl/Supported_Kernels

Google groups:

http://groups.google.com/group/open-iscsi/threads?gvc=2

http://groups.google.com/group/open-iscsi/topics

Open-iSCSI Wiki: http://www.open-iscsi.org/cgi-bin/wiki.pl

3. ATTO iSCSI initiator is available for Mac.

Website: http://www.attotech.com/xtend.html

4. Solaris iSCSI initiator

Version: Solaris 10 u6 (10/08)

1.4 IP SAN storage specifications

1.4.1 Technical specifications

 Controller features

1. Dual-active configuration support (only for DSN-6420)

2. Better performance, when comparing to other competitors' products in the same

segment

3. Cache mirroring through high bandwidth channels (only for DSN-6420)

4. Flexible RAID group (RG) ownership management (only for DSN-6420)

 Each RG can be assigned to one of the two controllers

 Each LUN can be exported from both controllers

5. Management port seamless take-over (only for DSN-6420)

14

 The management port can be transferred smoothly to the other controller with

the same IP address

6. Online firmware upgrade, no system down time (only for DSN-6420)

7. Multiple target iSCSI nodes per controller support

 Each LUN can be attached to one of 32 nodes from each controller

8. Front-end 2 x 10GbE iSCSI ports with high availability/load balancing/fail-over support

per controller

 Microsoft MPIO, MC/S, Trunking, LACP, and etc.

9. SBB Compliant

 System key components

1. CPU: Intel Xscale IOP 81342

2. Memory: 4GB DDRII 533 DIMM

3. Hardware iSCSI off-load engine

4. 2 x UARTs: serial console management and UPS

5. Fast Ethernet port for web-based management use

6. Backend: 12 x SAS or SATA II drive connections

7. Front-end: 2 x 10GbE iSCSI ports per controller

8. Hot pluggable BBM

9. SAS JBOD expansion port for expansion

10. Multiplexer board support for SATA drives (optional, on Dual controller mode)

11. Two power supplies

12. Redundant fans

 RAID and volume operation

1. RAID level: 0,1,0+1,3,5,6,10,30,50, 60, JBOD, and N-way mirror

2. Up to 1024 logical volumes in the system

3. Up to 32 PDs can be included in one volume group

4. Global and dedicated hot spare disks

5. Write-through or write-back cache policy for different application usage

6. Multiple RAID volumes support

7. Configurable RAID stripe size

8. Online volume expansion

9. Instant RAID volume availability

10. Auto volume rebuilding

11. On-line volume migration with no system down-time

 Advanced data protection

1. D-Link writeable snapshot

 Built-in snapshot with rollback enabled

 Snapshot enabled up to 16 volumes, each logical volume supports up to 32

snapshot volumes, total 512 snapshot volumes per system

2. Microsoft Windows Volume Shadow Copy Services (VSS)

3. Configurable N-way mirror for high data protection

4. Online disk roaming

15

5. Instant volume configuration restoration

6. Smart faulty sector relocation

7. Hot pluggable battery backup module support

 Enclosure monitoring

1. S.E.S. inband management

2. UPS management via dedicated serial port

3. Fan speed monitors

4. Redundant power supply monitors

5. Voltage monitors

6. Thermal sensors for both RAID controller and enclosure

7. Status monitors for D-LINK SAS JBODs

 Management interface

1. Management UI via

 serial console

 SSH telnet

 HTTP Web UI

 secured Web (HTTPS)

2. Notification via

 Email

 SNMP trap

 Browser pop-up windows

 Syslog

 Windows Messenger

3. iSNS support

4. DHCP support

 iSCSI features

1. iSCSI jumbo frame support

2. Header/Data digest support

3. CHAP authentication enabled

4. Load-balancing and failover through MPIO, MC/S, Trunking, and LACP

5. Up to 32 multiple nodes support

6. VLAN support

 Host connection

1. 2 x 10GbE iSCSI ports per controller

2. Host access control: Read-Write and Read-Only

3. Up to 128 sessions per controller

4. One logic volume can be shared by as many as 16 hosts

 OS support

16

 Windows

 Linux

 Solaris

 Mac

 Drive support

1. SAS

2. SATA II (optional)

3. SCSI-3 compliant

4. Multiple IO transaction processing

5. Tagged command queuing

6. Disk auto spin-down support

7. S.M.A.R.T. for SATA II drives

8. SAS JBODs expansion

 Power and Environment

 AC input: 100-240V ~ 7A-4A 500W with PFC (Auto Switching)

 DC output: 3.3V-21A; 5V-39A; 12V-30A

 Operating Temperature: 0 to 40 ℃

 Relative Humidity: 5% to 95% non-condensing

 Dimensions

2U 12 bay 19 inch rackmount chassis

442.8mm x 500.6mm x 88.0mm (W x D x H)

1.4.2 FCC and CE statements

FCC statement

This device has been shown to be in compliance with and was tested in accordance with

the measurement procedures specified in the Standards and Specifications listed below

and as indicated in the measurement report number: xxxxxxxx-F

Technical Standard: FCC Part 15 Class A (Verification)

IC ICES-003

CE statement

This device has been shown to be in compliance with and was tested in accordance with

the measurement procedures specified in the Standards and Specifications listed below

and as indicated in the measurement report number: xxxxxxxx-E

Technical Standard: EMC DIRECTIVE 2004/108/EC

17

(EN55022 / EN55024)

UL statement

FCC statement

This device has been shown to be in compliance with and was tested in accordance with

the measurement procedures specified in the Standards and Specifications listed below

and as indicated in the measurement report number: xxxxxxxx-F

Technical Standard: FCC Part 15 Class A (Verification)

IC ICES-003

CE statement

This device has been shown to be in compliance with and was tested in accordance with

the measurement procedures specified in the Standards and Specifications listed below

and as indicated in the measurement report number: xxxxxxxx-E

Technical Standard: EMC DIRECTIVE 2004/108/EC

(EN55022 / EN55024)

UL statement

Rack Mount Instructions - The following or similar rack-mount instructions are included

with the installation instructions:

A. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

ambient. Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by

the manufacturer.

B. Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not compromised.

C. Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

D. Circuit Overloading - Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might

have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

E. Reliable Earthing - Reliable earthing of rack-mounted equipment should be

maintained. Particular attention should be given to supply connections other than

direct connections to the branch circuit (e.g. use of power strips).

Caution

T

he main purpose of the handles is for rack mount use only. Do not use the

handles to carry or transport the systems.

18

The ITE is not intended to be installed and used in a home, school or public area

accessible to the general population, and the thumbscrews should be tightened with a tool

after both initial installation and subsequent access to the panel.

Warning: Remove all power supply cords before service

This equipment intended for installation in restricted access location.

 Access can only be gained by SERVICE PERSONS or by USERS who have been

instructed about the reasons for the restrictions applied to the location and about any

precautions that shall be taken.

 Access is through the use of a TOOL or lock and key, or other means of security, and

is controlled by the authority responsible for the location.

Caution

Risk of explosion if battery is replaced by incorrect type. Dispose of used

batteries according to the instructions.

19

Chapter 2 Installation

2.1 Package contents

The package contains the following items:

1. DSN-6410/6420 IP SAN storage (x1)

2. HDD trays (x12)

3. Power cords (x4)

4. RS-232 cables (x2), one is for console, the other is for UPS.

5. CD (x1)

6. Rail kit (x1 set)

7. Keys, screws for drives and rail kit (x1 packet)

8. SFP and 5 Meter cable

2.2 Before installation

Before starting, prepare the following items.

1. A host with a Gigabit Ethernet NIC or iSCSI HBA.

2. CAT 5e, or CAT 6 network cables for management port and iSCSI data ports.

3. Prepare storage system configuration plan.

4. Prepare management port and iSCSI data ports network information. When using

static IP, please prepare static IP addresses, subnet mask, and default gateway.

5. 10GbE switches (recommended). Or 10GbE switches with LCAP / Trunking (optional).

6. CHAP security information, including CHAP username and secret (optional).

2.3 Enclosure

2.3.1 Front view

Figure 2.3.1.1 (DSN-6410/6420)

Drive slot numbering

Slot 1 Slot 4 Slot 7 Slot 10

Slot 2 Slot 5 Slot 8 Slot 11

Slot 3 Slot 6 Slot 9 Slot 12

20

The drives can be installed into any slot in the enclosure. Slot numbering will be reflected

in web UI.

Tips

It is advisable to install at least one drive in slots 1 ~ 4. System event lo

g

s

are saved to drives in these slots; If no drives are fitted the event lo

g

s will

be lost in the event of a system reboot.

2.3.2 Front LED lights

There are three LED lights on the left frame bar.

Figure 2.3.2.1

 LED lights description:



Power LED:

 Green  Power on.

 Off  Power off.



Status LED:

 Red  System is failure.

 Off  System is good.



Access LED:

 Blue  Host is accessing.

 Off  Host is no access.







Page is loading ...

D-Link Storage User manual

This manual is also suitable for

D-Link Storage User manual

Related papers

Other documents