Value Hobby Apollo DLG User manual

Brand: Value Hobby

Model: Apollo DLG

Category: Remote controlled toys

Type: User manual

Apollo

ApolloApollo

Apollo DLG

DLG DLG

DLG

Discus Launch G

Discus Launch GDiscus Launch G

Discus Launch Glider

liderlider

lider

Almost-Ready-to-Fly

Instruction Manual

Specifications

Wing Span: 1550mm (61in)

Length: 1050mm (41in)

Wing area: 24.5sq dm (358sq in)

Weight (kit): 350g (12.35oz)

Airfoil: MH32

www.valuehobby.com/apollo-dlg.html

Dear Customer,

Congratulations on your purchase of Apollo DLG from Value Hobby. We thank you for your generous support,

and hope you enjoy your new airplane.

At Value Hobby, we hope to offer competitive prices, good performance, and products that you can setup and

use with ease. That’s why we extensively researched and tested this airplane, and suggested all the products

necessary for you to setup properly. We understand that you have many choices when purchasing, and we are

grateful you choose to buy from us.

As vendors, one of the most gratifying things for us is to hear from our customers. We would welcome any

suggestion to help us improve. Please make us aware of any errors and imperfections in the airplane or the

instructions, or about the setup that we suggested. We hope you’ll find our setup suggestions to be helpful, and

enjoy flying your new airplane. Please feel free to contact us at (630) 948-0947 or email us at

support@valuehobby.com

Disclaimer

By purchasing and/or building this model, user assumes ALL liability and risk involved with this product. This

model should be built and flown by an experienced pilot and only flown at AMA sanctioned sites.

Value Hobby guarantees this model to be free of defects in materials and workmanship at the date of purchase.

This warranty does not cover any parts damaged by use or modifications. In no way shall Value Hobby’s liability

exceed the original cost of the purchased model. Further, Value Hobby reserves the right to modify this warranty

without notice. Value Hobby has no control over the final stages of assembly or the material used for the final

assembly. No liability shall be assumed nor materials used for the final user-assembled product. By the act of

using the final product the user accepts all resulting liability. Value Hobby, as a R/C product vendor, provides a

top quality airplane and instructions to complete the model. The quality and flight characteristics of the finished

model depend greatly on how it is built; we cannot guarantee the performance for the completed model and

representations are expressed or implied as to the performance of the completed model. If the buyer is not

prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit

immediately, in new and unused condition.

Safety in Assembly

During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives. Please follow all

safety procedures recommended by the manufacturers of the products you use, and always follow these

important guidelines:

ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power tools. Safety glasses

are the best way to protect your eyes.

ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, or tools, especially

power tools. Do not cut toward exposed skin with hobby knives. Do not place hobby knives on tables or benches

where they can roll off or be knocked off.

ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially power tools.

ALWAYS keep hobby equipment and supplies out of the reach of children.

www.valuehobby.com/apollo-dlg.html

Safety in Flying

This is NOT a toy! It is a very high-performance RC airplane capable of high speeds and extreme maneuvers. It

should only be operated by a competent pilot in a safe area with proper supervision.

ONLY fly your aircraft in a safe, open area, away from spectators and vehicles–and where it is legal to fly.

NEVER fly over an unsafe area, such as a road or street.

Never fly too close to yourself or spectators.

Never run your motor inside a house or building with the propeller attached – Remove the prop for safety.

Required Items

CA Glue – Thin and Thick

Epoxy glue

Hobby Knife

Small Phillips Screwdriver

Set Metric Allen Wrenches

Scissors

Small Pliers

Wire Cutters

Masking tape

Optional – Heat gun

Before Starting Assembly

Examination

Unpack your airplane and examine the components. Check for damage of any kind. If you see any damage,

please contact Value Hobby immediately.

Covering

Your airplane was packed in plastic at the factory without any wrinkles in the covering. You may notice some

wrinkles now; more likely, you will notice a few in a day or two or the first time you take the plane out to the

flying field. These wrinkles are the result of wood shrinkage and/or expansion. Balsa wood changes size and

shape slightly as it is exposed to varying humidity in the air. This is a natural property of balsa wood. As your

airplane adjusts to the weather in your part of the world, wrinkles may appear and disappear. Wrinkles may be

removed with the gentle application of heat to the covering material on your airplane. The best tool to use is a

hobby heat gun. Apply the heat gently: the covering material will shrink as you apply the heat, and this will

remove the wrinkles. BE CAREFUL! Too much heat applied too quickly can damage the covering, either by

causing it to pull away from the wood at seams and corners or even by melting it. The covering will shrink at low

temperature with patient application of heat.

Wrinkles in the covering DO NOT affect flight performance.

Remove the canopy before attempting to use heat on your covering! The canopy is made of thermo-activated

plastic and WILL deform with the application of heat. Do not apply heat to the canopy.

If you need to clean your airplane, we recommend using a damp towel. The paint used on the canopy and cowl is

not safe for all cleaners. In particular, DO NOT use alcohol on these parts, it will remove the paint

www.valuehobby.com/apollo-dlg.html

Recommended Setup

Main Parts of the Airplane

Accessories and small parts not pictured

Configuration Model Qty

Radio 4 channel 1

Speed Control 3A Brushless ESC 1

Recommended

Battery LiPO GForce 20C 240mAh 2S 7.4V LiPO 1

Servos 9g servos 4

Y-Harness Universal Servo Y-Harness 300mm 11.8-Inch (Futaba "J" and

JR Compatible) 1

Extension Universal Servo Extension 600mm 23.6-Inch (Futaba "J" and

JR Compatible) 2

Charger GT POWER X-CHARGER C6 6S LiPO Charger 1

www.valuehobby.com/apollo-dlg.html

Section 1: Horizontal Tail Installation

Step1. Locate the horizontal tail wing.(The

measurement shows the location of the mounting

block).

Step2. Remove the covering for the tail boom

mounting block on the horizontal stabilizer.

Step3. Mix some epoxy, and glue the mounting block

onto the stabilizer.

Step4. Place the tail boom on the horizontal tail and

adjust tail boom to make the distance of AB is 400mm

(15.7in).

Step5. Apply some epoxy to glue the tail boom to the

mounting block. (Adjust the horizontal tail to make it

parallel to the wing).

Step6. Use a clamp to hold the tail boom and block

until the epoxy cures. (Clamp sold separately.)

www.valuehobby.com/apollo-dlg.html

Section 2: Vertical Tail Installation

Step1. Mark on the vertical fin where 70mm (2.8in)

from the left edge of the vertical tail is.

Step2. Insert the vertical tail into the tail boom and

adjust the vertical tail to make the left edge of tail

boom is aligned with the marked line.

Use a felt-tipped pen to trace the outline of the tail

boom onto the vertical stabilizer.

Step3. Cut and trim the coverings inside the lines

drawn in the pervious step, and remove it.

Step4. Use the CA to glue the vertical tail to the tail

boom. (Adjust to make the vertical tail perpendicular

to the wing).

Note: As shown, when finishing the installation. A=A1,

B=B1, C=C1

www.valuehobby.com/apollo-dlg.html

Section 3: Elevator and Rudder Servo

and Linkage Installation

Step1. Install two servos on the servo mounts.

Step2. Thread the 790mm (31.1in) pushrod wire into

the tail boom. The z-bend will be towards the tail.

Step3. Install the servo arm with pushrod connector

in the servo. Center the servo arm electronically and

slide the pushrod wire into the connector.

Step4. Thread the pushrod wire into the clevis and

tighten the bolt.

Connect the clevis to the control horn.

Position the control horn on the rudder, the pushrod

wire will be aligned with the tail boom, and drill the

mounting holes for the bolts.

Step5. Use three M2*10mm (.4in) bolts to secure the

control horn to the rudder.

Step6. Center the control surface and tighten the

screw on the pushrod connector.

www.valuehobby.com/apollo-dlg.html

Step7. Finish the elevator servo and linkage

installation in the same way.

Section 4: Aileron Servo and Linkage

Installation.

Step1. Locate the items shown in the picture.

Step2. Glue two servo mounting blocks to the hatch

inside the markings.

Step3. Use two M2*8mm (.3in) self-tapping screws to

secure the two blocks wont loose. (Center the servo

arm before mounting.)

Step4. Use two M2*8mm (.3in)self-tapping screws to

mount the servo to the blocks.

Step5. Remove the coverings on the wing for the

servo wires as shown.

Step6. Thread the servo wire through the wing.

www.valuehobby.com/apollo-dlg.html

Step7. Thread the clevis onto the aileron pushrod and

connect the clevis to the servo arm.

Mount the servo hatch to the wing using four

M2*8mm (.3in) self-tapping screws.

Step8. Use glue and two hinges to attach the aileron

to the wing.

Step9. With the pushrod wire 90-degrees to the hinge

line, connect the pushrod wire to the servo control

horn using a pushrod connector.

Step10. Repeat the pervious steps to finish the other

aileron servo installation.

Section 5: Wing Installation

Step1. Locate the items shown in the picture.

Step2. Insert the two wing tubes

{10mm(.4in)*128mm(5.0in) and Ф80mm(3.1in)}into

the wing panel, and slide the other panel onto wing

tube.

Step3. Attach the wing onto the fuselage using two

bolts plate and four M3 Allen bolts. Tighten the bolts

using a screwdriver. {Two M3*30mm (1.2in) bolts are

for the front plate, and two M3*25mm (1.0in) bolts

for the other one}.

www.valuehobby.com/apollo-dlg.html

Section 6: Battery Installation

Install the battery into the fuselage as shown. Sponge

can be used to prevent the battery from moving.

Section 7: Canopy Installation

Use a M2*8mm (.3in) self-tapping screw to secure

the canopy onto the fuselage.

Section 8: Throwing Peg Installation

If you are right handed, remove the covering from the

hole in the left wing tip. If you are left handed,

remove the covering from the hole in the right wing

tip.

Push the carbon throwing peg into the hole in the

wing tip. Apply a small amount of epoxy to the peg

and twist the peg so that the epoxy goes into the

wing and the peg is centered vertically in the wing.

Section 9: Adjust the CG.

For the first flights, the recommended Center of

Gravity location is 260mm (10.2in) behind the nose.

Use the battery pack, moving it forward or backward,

to achieve the correct balance.

Section 10: Set the Control Throws

Use a ruler to accurately measure and set the control

throw of each control surface as indicated in the chart.

If your radio does not have dual rates, we recommend

setting the throws at the high rate.

Low Rate High Rate

ELEVATOR

.24’’(6mm) up .37’’ (9.5mm) up

.24’’ (6mm) down .37’’ (9.5mm) down

AILERONS

.37’’ (9.5mm) up .63’’ (16mm) up

.37’’ (9.5mm) down .63’’ (16mm) down

RUDDER

.24’’ (6mm) right .37’’ (9.5mm) right

.24’’ (6mm) left .37’ ’(9.5mm) left

www.valuehobby.com/apollo-dlg.html

Section 11: Method of Throwing

Step1. Your right index finger and middle finger

should be wrapped around the peg.

Step2. Stand with your left shoulder into the wind

and the right wing tip on the ground.

Step3. Start rotating to the left keeping the plane flat

and your arm extended.

Step4. This is the second half of the rotation and the

section that is most responsible for a good high lunch.

Do not use too much arm in this section. Just let the

rotation of your torso speed the plane up.

Step5. By this time in the launch, the plane will be

trying to climb on its own. Just release your fingers

and let the plane fly out of your hand. Try to release it

directly into the wind.

Step6. This last step is just to catch your balance and

watch your plane climb for the clouds.

www.valuehobby.com/apollo-dlg.html

www.valuehobby.com

2012-10-29

Value Hobby Apollo DLG User manual

Brand: Value Hobby

Model: Apollo DLG

Category: Remote controlled toys

Type: User manual

Download PDF

report

Value Hobby Apollo DLG User manual

Value Hobby Apollo DLG User manual

Related papers

Other documents