ESAB Wheel Cart Kit User manual

ESAB
Brand
ESAB
Model
Wheel Cart Kit
Category
Multimedia carts & stands
Type
User manual
The Wheel Cart is an accessory that permits rolling a
Mig 4HD, Mig 2E, DuraDrive 4-30 or DuraDrive 4-48HD
Wire Feeder or a PCM-500i or PCM-875 Plasma Power
Source around the job site with ease.
The kit includes the following parts:
1 - Base, 34138
2 - Swivel Wheel, 950396
2 - Stationary Wheel, 950472
1 - Strap 34146
2 - Clip, 36905
2 - Screw, 1/4”-20 x 0.50”
16 - Nut, 1/4”-20
18 - Lockwasher, 1/4”
4 - Screw, #10-32 x .38LG
4 - Lockwasher #10
Assemble as follows:
1. Assemble stationary casters on one end of cart
base and the swivel casters on the other using 16
supplied lockwashers and nuts. Tighten each nut
firmly.
2. If using the cart for the Mig 4HD or 2E Wire Feeder,
position the wire feeder on the cart and then se-
cure to cart with the supplied strap (34146) and
two screws and lockwashers as illustrated. Tighten
all screws firmly.
F-15-390-A
February, 2002
STRAP - 34146
(2) LOCKWASHER 1/4”
(2) SCREW 1/4”-20 X 1/2”
(2) NUT 1/4”-20
CLIP - 36905
(2) LOCKWASHER 1/4”
(2) SCREW 1/4”-20 X 1/2”
WHEEL CARWHEEL CAR
WHEEL CARWHEEL CAR
WHEEL CAR
T KITT KIT
T KITT KIT
T KIT
P/N 34324
3. If using the cart for PCM-500i or 875, position the
unit on the cart as shown. Remove the bottom
middle panel mounting screw and assemble the
supplied right angle clip (36905) with the same
panel mounting screw to each side of the unit.
Secure the unit to the base using two supplied
screws, lockwashers and nuts. Make sure all
screws are tightened firmly,
Instructions for the DuraDrive 4-30 or DuraDrive
4-48 Wire Feeder are found on the back of this
publication.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
Mig 4HD and 2E
PCM-500i and 875
F-15-390-A 2/02
(4) Screw #10-32-.38
(4) Lockwasher #10
Clip - 36905
(2) Screw 1/4”-20-.50
(Hex Head)
(2) Lockwasher 1/4”
Note that 36905 clip fits under
and behind the base of the wire
feeder.
4.
If using the cart for the DuraDrive 4-30 or DuraDrive
4-48 Wire Feeder, position the Wire Feeder on the
cart, secure the two supplied right angle clips
(36905) at the front and rear of the feeder using
the screws and lockwashers supplied. Secure the
clips to the cart using supplied screws and
lockwashers as shown below. Make sure all screws
are tightened firmly.
DuraDrive 4-48HD and 4-30
  • Page 1 1
  • Page 2 2

ESAB Wheel Cart Kit User manual

ESAB
Brand
ESAB
Model
Wheel Cart Kit
Category
Multimedia carts & stands
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents