Liebherr 7083-103-00 User manual

Liebherr
Brand
Liebherr
Model
7083-103-00
Category
Fridges
Type
User manual

This manual is also suitable for

7083 103-00
ECBN 62
Installation instructions
for NoFrost combined refrigerator-freezers
2
Setting up
• Avoidpositioningtheapplianceindirectsunlightornearcook-
ers,radiatorsandsimilarsourcesofheat.
• Theflooronwhichtheappliancestandsshouldbehorizontal
andlevel.
• Theventilationgrillesshouldnotbeobstructed.Alwaysensure
thatthereisgoodventilationandthattheoutwardflowingairis
abletoescape.
• StandardEN378specifiesthattheroominwhichyouinstall
yourappliancemusthaveavolumeof1m³per8gofR600a
refrigerantusedintheappliance,soastoavoidtheformationof
inflammablegas/airmixturesintheroomwheretheappliance
islocatedintheeventofaleakintherefrigerantcircuit.The
quantityofrefrigerantusedinyourapplianceisindicatedon
thetypeplateontheinsideoftheappliance.
Appliance dimensions
Appliance venting
Therequiredairflowisdirectedthroughtheplinth.
Itisimportanttousetheprovidedventilationgrillefortheventila-
tionopening.
The ventilation opening must not be
obstructed or covered with a panel!
Electrical connection
Onlyoperatetheappliancewithalternating current (AC).
The permissible voltage and frequency are indicated on the
typeplate.
Thesocketmustbeproperlyearthedandprotectedbyafuse.
Thetrippingcurrentofthefusemustbebetween10Aand16A.
Thesocketmustnotbesituatedbehindtheappli-
anceandmustbeeasilyaccessible.
Donotconnecttheapplianceusinganexten-
sioncableorextensionsocket.
Donotusestand-aloneinverters(conversion
ofdirectcurrenttoalternatingcurrent/three-
phasecurrent)orenergy-savingplugs.Risk
ofdamagetotheelectroniccontrolsystem!
3
Installation dimensions
Theicemakerisfittedinthefreezercompartmentofthecom-
bined refrigerator-freezer. It must be connected to the mains
watersupplytowork.
Thewatershut-offtapmustbepositionedwithintheareasmarked
ingrey.
Thesocketmustbepositionedwithintheareasmarkedingrey
orabovetheinstallationrecess.
WARNING!
The water shut-o tap must not sit directly
above the socket!
The gap between the water shut-o tap and
the socket must comply with the regulations
of the country in which the appliance is used!
Cabinet depth D
625 mm + panel thickness>Insetinstallationstyle
625 mm>Framelessinstallationstyle
Explanationof"Installationstyles"seepage4.
4
Definition of Inset Installation Style
Applianceandpanelssitfullywithintheopeningandareflush
withwhatcouldbeitsownbox,betweentwopantrycabinetsor
decorativecolumns.
Definition of Frameless Installation Style
Withthisinstallationstyle,thesewiderappliancepanelspartially
overlaythesharedsidegablesofadjacentcabinetrysoasto
mimicthelookofaframelessstylecabinet.
Side view of cabinet (sectional view)
Cabinet frame
Doorpanel
Side view of cabinet (sectional view)
Cabinet frame
Doorpanel
5
Panel dimensions - Inset installation style
Min.panelthickness=16mm
Max.panelthickness=19mm
Maximum panel weight
Refrigeratorpanel=12kg
Freezerdrawerpanel=10kg
Panel dimensions - Frameless installation style
6
Right side wall of appliance housing
Front of
appliance housing
Top View
Frontpanel-doorclosed
Panel
thickness
Panel
thickness
Frontpanel-dooropeningangle=105°
Door swing clearance - Inset Installation Style
7
Door swing clearance - Frameless Installation Style
Right side wall of appliance housing
Front of
appliance housing
Top View
Frontpanel-doorclosed
Panel
thickness
Panel
thickness
Frontpanel-dooropeningangle=105°
8
Mounting the anti-tipping device
WARNING!
The supplied anti-tipping bracket must be installed in all
cases. This prevents the appliance from tipping over when
the fully loaded door is opened.
CAUTION!
Ensure that there are no electric cables or water pipes in
the wall section to which the anti-tipping bracket is to be
secured. These could be damaged during installation.
Important!
When securing the anti-tipping bracket to a concrete floor,
use suitable plugs!
If the floor slopes down sideways, the anti-tipping
bracket must be fitted horizontally. Lay down spacers
in the appropriate positions.
Wall
Connection to the water supply
Safety instructions and warnings
•Donotconnecttothewatersupplywhilethecombinedrefrig-
erator-freezerisconnectedtotheelectricitysupply.
• The connection to the mains water supply may only be
made by trained personnel.
• The water quality must comply with the drinking water
directives of the country in which the appliance is used.
•Theicemakerisdesignedexclusivelytomakeicecubesin
quantitiesrequiredbyahouseholdandmayonlybeoperated
withwatersuitableforthispurpose.
• Allrepairsandworkontheicemakermayonlybecarriedout
bycustomerservicepersonnelorothertrainedpersonnel.
• The manufacturer cannot accept liability for damage
caused by a faulty connection to the mains water supply.
Water pressure
The water pressure must be between 150 and
600 KPa (1.5 - 6 bar).
Important!
Ifthewaterfilter
isinsertedintheappliance,thewater pressure
mustliebetween300 and 600 KPa (3 - 6 bar).
If the water pressure with the inserted water
filter is too low, this may cause the ice maker to
malfunction.
Thewatersupplytotheappli-
ancemustbethroughacold
waterpipethatcanwithstand
the operating pressure and
complies with the hygiene
regulations.
Forthis,usethestainlesssteelhosesupplied(length3m).
1. Markthecentrelineoftheapplianceon
thefloor.Align the anti-tippingbracket
centretothecentreline.
2. Securetheanti-tippingbracket
to the floor using the 3screws
(6mmx60mm)includedinthe
accessorypack.
ThedistanceEbetweentheleadingedgeofthebodyoftheunit
andtherearedgeoftheanti-tippingbracketis
Inset installation style > 610 mm + panel thickness
Frameless installation style > 610 mm
9
3. Insertthebentsectionofthehosethrough
theopeningattherearoftheappliance.
4. Connectthehosetothesolenoidvalve
atthefrontsideoftheappliance.
WARNING!
Do not connect the appliance to the power supply until the
installation is completed.
CAUTION!
Lay the mains cable and the water hose in such a way
that they will not be damaged when the appliance is slid
into the installation recess.
Anti-tippingbracket
Compressormounting
plate
Wall
Appliance
7. Pushtheapplianceslowlyintotherecessuntilthecompressor
mountingplatetouchestheanti-tippingbracket.
WARNING!
To prevent the appliance from tipping forwards, the com-
pressor mounting plate must be touching the anti-tipping
bracket!
8. Connectthehosetotheshut-offtap.
 Opentheshut-offtapandcheckthesystemforleakage.
Important!
Aftertheicemakerhasbeenswitchedon,thewatersupplysystem
mustbebled.SeethesectionBleeding the ice makerinthe
operatinginstructions.
5.
6.
6. Route the water hose
towardsthewatershut-
offtap.
5. Route the mains cable
towardsthesocket.
Installation
1. Place the appliance in front of the
installationrecess.
2. Applycoverstripsonthe
side walls of the appli-
ance.
10
Levelling the appliance
1. Adjusttheheightofthe
applianceatthefrontby
twisting the adjustable
feet
1
(A/F27). Use
theopen-endedspanner
provided.
Caution!
The front feet of the ap-
pliance must be firmly
placed on the floor.
2. Adjusttheheightoftheappliance
attherearbyturningtheadjusting
bars
2
.
 Turn the adjusting barsclock-
wiseuntilthecompressormount-
ingplatetouchestheanti-tipping
bracket.
Before fitting the door panels
Removethecover
1
andunscrewtheattachmentbracket
2
fromtherefrigeratordoors.Theseattachmentbracketswillbe
mountedontotherefrigeratordoorpanels.
Important!
The securing nuts are needed for re-mounting the pre-
assembled door panels onto the refrigerator doors.
Unscrewtheattachmentbrackets
3
fromthefreezerdrawers.
These attachment brackets will be mounted onto the freezer
panels.
Important!
The screws are needed for re-mounting the pre-assembled
freezer panels onto the freezer drawers.
Adjusting the front of the drawer
Ifrequired,thefrontofthefreezerdrawerscanbeadjusted.
Transferthescrewsshownintheillustration(ontheleftandright
sidesofthefreezerdrawer)individuallytothelongslotsbelow.
Tighten thescrewsinthe front of thedrawer onceitisinthe
rightposition.
Side view of the freezer drawer
pulled out
Fasten the appliance in the recess
screws
(4x16mm)
Fasten the appliance in the
recess through the upper and
lowerhingesoftherefrigerator
doors.
Use2screwsforeachhinge.
11
Mounting the attachment brackets onto the door panels
Marklinesontherefrigeratordoorpanelsasshownin
Fig. A.
Alignthedismountedbracketsoftherefrigeratordoorstothelinesontherefrigeratordoorpanelsasshownin
Fig. A 1.
Fasteneach
bracketwithanyholewhereverpossibleusingaminimumof6screws4x16mm.
Fastenthebracketsprovidedontothefreezerdrawerpanelsusingthreescrews(4x16mm)foreachbracket(
Fig. A2)
.
Fig. A Fig. A 2
Fig. A 1
Refrigerator door panels
Freezer drawer panel
Freezer drawer panel
Fig. A 2
12
Mounting the refrigerator panel
Thedescriptionisforonepanelonly.Theprocedureisthesame
forbothpanels.
fig. B
fig. C
1. Opentherefrigeratordoorandsuspendtherefrigeratorpanel
onthetopadjustingpins(fig. B).
2. Screwsecuringnutsontotheadjustingpinsandslightlytighten
(fig. B).
3. Closetherefrigeratordoorandchecktheheightofthepanel.
4. Adjusttheheightofthepanelifnecessary.Undothesecuring
nutsandusetheadjustingpinstoadjust(fig. C).
Tomakeitpossibletofastentherefrigeratorpanelatthebottom
thesoft-stopcylindermustbedismantled.
6. Graspthesoft-stopcylinderandpulldown(Fig. D).
Thesoft-stopcylinderretractsinthedetachedstate.
fig. D
7. Transfertheloweredgeoftheattachmentbracketontothe
panel using a pencil. (fig. E).Remove thepanel from the
refrigeratordoor.
fig. E
13
fig. G
fig. K
7. Dismantlethelowerattachmentbracketfromtherefrigerator
door.Alignthebrackettothelinesontherefrigeratordoor
panel.(fig. G).
 Fastenthebracketwithanyholewhereverpossibleusinga
minimumof6screws4x16mm.
fig. H
8. Opentherefrigeratordoorandsuspendtherefrigeratorpanel
onthetopadjustingpins(fig. H).
9. Screw securing nuts onto the adjusting pins and slightly
tighten(fig. H).
10. Movethepanel to the left until it makescontact with the
centerrail(fig. I).
11. Tightenthehexnutsfinally.
fig. I
12. Fastentherefrigeratorpanelusingthesamescrewsthat
heldthelowerbracketbeforeremoval(fig. K).
13. Extendthesoft-stopcylinderandconnectwiththeballstud
(fig. L).
fig. L
14. Clickcoverintoplace(fig. M).
fig. M
14
Mounting the dust filter
T h es up p li e ddu s tf i l te r p reve nt s th a t dir t e nte r st h em oto r c om par t -
ment,reducingtherefrigerationperformance.Thereforealways
installthedustfilter.
1. Pullthebottomfreezerdrawerrightout.
2. Removetheprotectivefilmfromthedustfilter.Insertthefilter
atthebottom,pressthebuttondownandclickthefilterinto
place.
Mounting the ventilation grille
Important!
To ensure fault-free operation of the appliance, you must
install the supplied ventilation grille.
Do not obstruct the ventilation opening or cover it with a
panel!
Mounting the freezer panels
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled
panel.Thesamescrewsmustbeusedasthoseusedtoscrew
ontheattachmentbrackets(3.5x13).
2. Closethefreezerdrawerandcheckthepositionofthepanel.
Adjusttheheightofthepanelbyundoingtheleftandright
screws.Tightenthescrews.
3.Pulloutthebottomfreezerdrawerandmountthepanelinthe
sameway.
4. Forbothdrawers,coverthegapbetweenthedrawerandthe
panelwiththecoverstripssupplied.Removetheprotective
filmfromthetrimandinsertintothegapatthetop.
3.5x13mm
15
LiebherrHausgeräteLienzGmbH*Dr.-Hans-Liebherr-Strasse1*A-9900Lienz**www.liebherr.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Liebherr 7083-103-00 User manual

Liebherr
Brand
Liebherr
Model
7083-103-00
Category
Fridges
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents