Stairmaster HIITMill X 9-4640 Owner's manual

Brand: Stairmaster

Model: HIITMill X 9-4640

Type: Owner's manual

This manual is also suitable for

Install

Page 1

620-8587 Rev. C

HIIT Console Wall Power Upgrade Install Instructions

Applies to: Airt, Airt UB, HIIT Bike, HIIT UB, HIITMill, HIITMill X, HIIT Rower

Enhanced Images: Pictures can be zoomed in to any level for detail.

Use the standard zoom tools for your platform to zoom in.

HIIT UB

STEP 1: Remove the mast grommet then use a

3mm allen key to remove the two (2) M6 x 16mm

screws securing the user right shroud to the frame.

STEP 2: Remove the user right side shroud by us-

ing a #2 phillips screwdriver to remove the three

(3) #8-18 x 1.25” screws then use a 3mm allen

key to remove the two (2) M5 x 16mm screws.

Finally, use a 5mm allen key to remove the one

(1) M8 x 20mm screw securing the shroud to the

frame.

STEP 3: Connect the end of the HIIT Console Wall

Power adapter to the end of the Console Power

Cable

STEP 4: Replace the user right side shroud removed

in Step 2, then route the Console Power Cable down

the frame and out of the bottom of the shroud - as

indicated by the bold line. Use a cable tie to secure

the Console Power Cable to the frame, indicated by

the arrow Finally, connect the power adapter to the

Console Power Cable.

Install

Page 2

620-8587 Rev. C

Airt UB

STEP 1: Remove the mast grommet then use a 3mm

allen key to remove the two (2) M6 x 16mm screws

securing the user right shroud to the frame.

STEP 2: Remove the user right side shroud by using a

#2 phillips screwdriver to remove the three (3) #8-18

x 1.25” screws then use a 3mm allen key to remove

the two (2) M5 x 16mm screws. Finally, use a 5mm

allen key to remove the one (1) M8 x 20mm screw

securing the shroud to the frame.

STEP 3: Use a 3mm allen key to remove the four (4)

M5 x 12mm screws securing the user left side shroud

to the frame, then remove the shroud.

STEP 4: Remove the console grommet and the

Console Adapter Cable from the console mount then

connect the long Console Power Cable (the short

cable is used for the HIITMills) to the Console Adapt-

er Cable.

NOTE: There should only be one input available

on the Console Adapter Cable as the other end is

plugged into the RPM sensor.

Install

Page 3

620-8587 Rev. C

STEP 5: Use a #2 phillips screwdriver to remove the

ve (5) 8-18 x 3/4” screws (3 securing the shroud, 2

securing the shroud bracket) then use a 3mm allen

key to remove the three (3) M5 screws securing the

shroud to the frame.

NOTE: Removing the user right boom shroud may

require the boom to be rotated all the way up. To

do this, pull the boom adjustment lever toward the

user, push the boom upward until it stops, then

release the boom adjustment lever.

STEP 6: Use a #2 phillips screwdriver to remove the

four (4) 8-18 x 3/4” screws securing the user right

boom shroud to the user left boom shroud then

remove the user right boom shroud.

STEP 7: Route the long Console Power Cable in-

stalled in Step 2.1 along the same path as the RPM

Sensor Cable (indicated by the bold line). Coil up

any excess wire and secure inside the machine away

from moving parts.

NOTE: The user right boom shroud is shown com-

pletely removed for clarity but the shroud can

remain on the machine as long as the wire can be

routed underneath.

STEP 8: Connect the end of the HIIT Console Wall

Power adapter to the end of the Console Power

Cable.

Install

Page 4

620-8587 Rev. C

STEP 9: Route the Console Power Cable down the

frame and out of the bottom of the shroud - as

indicated by the bold line. Use a cable tie to secure

the Console Power Cable to the frame, indicated by

the arrow. Replace the shrouds that were removed

in Steps 1, 2, 3, 5, and 6. Once all the shrouds have

been reinstalled, connect the power adapter to the

Console Power Cable.

Install

Page 5

620-8587 Rev. C

HIIT Bike

STEP 1: Using a #2 phillips screwdriver, remove

the two (2) M5 x 10mm screws securing the user

right side fan shroud to the frame then remove the

shroud.

STEP 2: Using a #2 phillips screwdriver, remove

the two (2) M5 x 10mm screws securing the user

right side fan shroud to the frame then remove the

shroud.

STEP 3: Once all have been removed, pull the mast

away from the frame revealing the Console Power

Cable. Remove the grommet on the user right side

frame, then route the Console Power Cable down

through the frame and out of the hole in the frame

where the grommet was removed. After routing,

reinstall the grommet and mast. Connect the power

adapter to the Console Power Cable and secure to

the frame using a cable tie where indicated by the

arrow. Finally, reinstall the shroud removed in Step 1.

Install

Page 6

620-8587 Rev. C

Airt Bike

STEP 1: Using a #2 phillips screwdriver, remove

the two (2) M5 x 10mm screws securing the user

right side fan shroud to the frame then remove the

shroud.

STEP 2: Remove the HIIT Console Adapter Cable

then connect the long Console Power Cable (the

short cable is used for the HIITMills) to the Console

Adapter Cable. Reinstall the HIIT Console Adapter

Cable and route the Console Power Cable as shown

in Step 3.

STEP 3: Route the Console Power Cable down the

user’s right side mast and down the frame as indi-

cated by the bold line. Use the supplied cable ties to

secure the Console Power Cable to the bike where

indicated by the arrows. Be sure to route the cable

underneath the user right side fan shroud removed

in Step 2. Once the cable is routed, reinstall the fan

shroud removed in Step 2 and connect the power

adapter to the end of the Console Power Cable.

Install

Page 7

620-8587 Rev. C

HIITMill + HIITMill X

STEP 1: Remove the brake cover using a 4mm allen

key to remove the three (3) M5 x 50mm screws se-

curing the brake cover to the unit.

STEP 2: Connect the Console Power Cable to the

empty 2-pin port on the Power Sensor as indicated

by the arrow, then reinstall the brake covers.

WARNING: When reinstalling the brake covers, en-

sure that no cables are touching the ywheel.

STEP 3: The Power Sensor calibration must be run on

the console before working out after reinstalling the

power sensor. To calibrate the Power Sensor:

A. Push the brake adjustment lever all the way for-

ward (away from the user).

B. Press and hold the level up, level down, and clock

buttons at the same time for 5-10 seconds.

C. Use the down arrow to navigate to page 6, then

push the clock button to set the zero-point angle.

D. Press the back button located between the up/

down arrow buttons to return to the main workout

screen.

STEP 4: Route the end of the Console Power Cable

out of the gap between the frame and the brake

cover, then plug the power adapter into the Console

Power Cable. Finally, use two cable ties to secure

the power adapter and Console Power Cable to the

frame as indicated by the arrows.

Install

Page 8

620-8587 Rev. C

HIIT Rower

TO ROWER

TO WALL

STEP 1: Install the power cord into the power adapter.

STEP 2: Insert the end of the power adapter into

the power inlet located on the console mast.

TO WALL

STEP 3: Route the power adapter cable as shown in image right, use the zip ties included with the power

kit to secure the cable to the HIIT Rower where indicated by the arrows.

STEP 4: After routing the cable, plug the power cable into the wall.

Stairmaster HIITMill X 9-4640 Owner's manual

Brand: Stairmaster

Model: HIITMill X 9-4640

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Stairmaster HIITMill X 9-4640 Owner's manual

This manual is also suitable for

Stairmaster HIITMill X 9-4640 Owner's manual

Related papers

Other documents