Behringer PMP1000 Owner's manual

Brand: Behringer

Model: PMP1000

Category: Audio mixers

Type: Owner's manual

This manual is also suitable for

User Manual

EUROPOWER

PMP6000

1600-Watt 20-Channel Powered Mixer with Dual Multi-FX Processor and FBQ Feedback

Detection System

PMP4000

1600-Watt 16-Channel Powered Mixer with Multi-FX Processor and FBQ Feedback

Detection System

PMP1000

500-Watt 12-Channel Powered Mixer with Multi-FX Processor and FBQ Feedback

Detection System

V 1.0

2EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Thank you

Congratulations! With the PMP1000/PMP4000/PMP6000 you have acquired a

state-of-the-art power mixer that sets new standards. Right from the very start

it has been our goal to design a revolutionary unit that can be used for a wide

variety of applications. Indeed, this overwhelming power mixer gives you plenty

of functionality and a broad range of connection and expansion options.

Table of Contents

Thank you .......................................................................2

Important Safety Instructions ...................................... 3

Legal Disclaimer ............................................................. 3

Limited warranty ............................................................ 3

1. Introduction ............................................................... 4

1.1 Before you get started ...................................................... 4

1.2 The manual ........................................................................... 4

2. Control Elements ....................................................... 8

2.1 Mono and stereo channels .............................................. 8

2.2 Equalizer and FBQ .............................................................. 9

2.3 Eects section .................................................................. 10

2.4 Main and monitor section ............................................. 10

2.5 Rear panel ........................................................................... 11

3. Digital Eects Processor ......................................... 11

4. Installation ............................................................... 13

4.1 Mains connection ............................................................. 13

4.2 Audio connections ........................................................... 13

4.3 Loudspeaker connections ............................................. 14

5. Wiring Examples ...................................................... 14

6. Specications ........................................................... 18

3EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Important Safety

Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

Terminals marked with this symbol carry

electrical current of sucient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modication should be performed only

by qualiedpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be sucient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

qualied personnel.

Caution

To reduce the risk of re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by qualied service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by qualied

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories specied by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table specied by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualied service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

17. Correct disposal of this

product: This symbol indicates

that this product must not be

disposed of with household

waste, according to the WEEE

Directive (2012/19/EU) and

your national law. This product

should be taken to a collection center licensed for the

recycling of waste electrical and electronic equipment

(EEE). The mishandling of this type of waste could have

a possible negative impact on the environment and

human health due to potentially hazardous substances

that are generally associated with EEE. At the same time,

your cooperation in the correct disposal of this product

will contribute to the ecient use of natural resources.

For more information about where you can take your

waste equipment for recycling, please contact your local

city oce, or your household waste collection service.

18. Do not install in a conned space, such as a book

case or similar unit.

19. Do not place naked ame sources, such as lighted

candles, on the apparatus.

20. Please keep the environmental aspects of battery

disposal in mind. Batteries must be disposed-of at a

battery collection point.

21.

This apparatus may be used in tropical and moderate

climates up to 45°C.

Music Tribe accepts no liability for any loss which may

be suered by any person who relies either wholly or in

part upon any description, photograph, or statement

contained herein. Technical specications, appearances

and other information are subject to change without

notice. All trademarks are the property of their

respective owners. Midas, Klark Teknik, Lab Gruppen,

Lake, Tannoy, Turbosound, TC Electronic, TC Helicon,

Behringer, Bugera, Aston Microphones and Coolaudio

are trademarks or registered trademarks of Music

Tribe Global Brands Ltd. © Music Tribe Global Brands

For the applicable warranty terms and conditions

and additional information regarding Music Tribe’s

Limited Warranty, please see complete details online at

musictribe.com/warranty.

4EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

1. Introduction

Further advantages are the integrated Voice Canceller that removes vocal

passages from playbacks, the FBQ function, which detects feedback frequencies,

and the Speaker Processing function for loudspeaker alignment—all with a

resolution of 24 bits and 40 kHz. Plus, our tried and tested XENYX Mic Preamps

give you crystal-clear audio free of noise and distortion when using microphones.

Behringer is a company with its roots in professional recording studio technology.

For many years we have been successful in developing products for studio and

live use. These include microphones and 19" units of all types (compressors,

enhancers, noise gates, tube processors, headphone ampliers, digital eects, DI

boxes, etc.), monitor and P.A. speakers and professional live and recording mixers.

Our entire technical know-how has gone into your PMPpowermixer.

1.1 Before you get started

1.1.1 Shipment

Your PMP was carefully packed at the factory and the packaging is designed

to protect the unit from rough handling. Nevertheless, we recommend that

you carefully examine the packaging and its contents for any signs of physical

damage which may have occurred during transit.

◊ ◊ If the unit is damaged, please do NOT return it to Behringer,

but notify your dealer and the shipping company immediately.

Otherwise, claims for damage or replacement may not be granted.

◊ ◊ We recommend that you use a flight case, so as to give your power

mixer optimum protection during use or transport.

◊ ◊ Always use the original packing carton to prevent damage during

storage or transport.

◊ ◊ Make sure that children cannot play unsupervised with the device or

its packaging.

◊ ◊ Please ensure proper disposal of all packing materials.

1.1.2 Initial operation

Be sure that there is enough air space around the unit for cooling and, to avoid

overheating, please do not place the EUROPOWER near radiators, etc.

◊ ◊ Blown fuses must be replaced by fuses of the same type and rating!

Please refer to the “Specifications” for details.

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certication requirements.

◊ ◊ Please make sure that all units have a proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or on the AC power cord.

To avoid damage on the device, do not

• • earth the loudspeaker outputs

• • connect the loudspeaker outputs to each other

• • connect the loudspeaker outputs to those of other ampliers

IMPORTANT NOTES CONCERNING INSTALLATION

The sound quality may diminish within the range of powerful broadcasting

stations and high-frequency sources. Increase the distance between the

transmitter and the device and use shielded cables for all connections.

1.1.3 Online registration

Please register your new Behringer equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warrantycarefully.

Should your Behringer product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the Behringer retailer from whom the equipment was purchased. Shouldyour

Behringer dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in the

original equipment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the distributor

nearest you. A list of distributors can be found in the support area of our website

(http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

1.2 The manual

This manual is designed to give you both an overview of all control elements and

to provide details about how to use them. To provide you with a clear structure,

we have grouped the control elements according to their function. They can

easily be found on the enclosed numbered illustrations. If you need more

detailed information on specic topics, please visit our web site at behringer.com.

5EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

EUROPOWER PMP1000 FRONT PANEL

(57) (58) (61) (62) (65)

(35)

(64)(60)

(22)

(55)

(18)

(19)

(20)

(21)

(31)

(36)

(43)

(44)

(40)

(47) (46) (54) (48)

(42)

(14)

(3)

(1) (2)

(4)

(6)

(8)

(9)

(11)

(13)

(16)

(17)

(27)

(26)

(30)

(32)

(33)

(34)

(39)

(37)

(56)

(52)

(29)

6EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

EUROPOWER PMP4000 FRONT PANEL

(18) (23)

(56) (55) (57) (58) (59)

(62)

(63)

(64)

(65)

(22)

(19)

(20)

(21)

(24)

(25)

(35)

(36)

(38)

(37)

(40)

(45)

(46) (47) (48) (49)

(41)

(52)

(42)

(53)

(54)

(33)

(32)

(34)

(31)

(44)(43)(27)

(61) (60)

(26)

(30)

(14)

(1) (2)

(4)

(3)

(5)

(6)

(8)

(9)

(10)

(11)

(13)

(15)

(16)

(17)

7EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

EUROPOWER PMP6000 FRONT PANEL

(56) (57) (58) (59)

(62)

(63)

(64)

(65)

(61)

(26) (27) (28) (29)

(34)

(31)

(32)

(33)

(54)

(53)

(52)

(42)

(50)

(41)

(51)

(22)

(23)

(18)

(19)

(20)

(21)

(24)

(25)

(35)

(36)

(37)

(38)

(39)

(43)

(40)

(44)

(45)

(14)

(1) (2)

(4)

(3)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(15)

(16)

(17)

(49)(48)(47)(46)

(55)

(60)

8EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

EUROPOWER PMP6000 REAR PANEL

(66) (69) (70)

(71)(72)(68)(67)

2. Control Elements

A detailed description of all functions of your power mixer can be found in the

following chapters. Please also refer to the enclosed sheet with the numbered

illustrations to get a good overview of the control layout.

2.1 Mono and stereo channels

(1) Use the GAIN control to adjust the input gain. Be sure to set this control

fully counter-clockwise before you connect or disconnect a signal source to

an input. GAIN controls both the microphone and the LINE input. Theblack

scale shows the microphone gain (+10 to +60 dB on channels with XENYX

MIC PREAMPS and 0 to +40 dB on conventional microphone inputs;

PMP1000 only, channels 5/6 and 7/8).

The “LINE” scale indicates the sensitivity of the LINE input, ranging from

+10to -40 dBu.

PMP1000: The mono/stereo combination channels 5/6 and 7/8 have a

sensitivity of +20 to -20 dBu.

(2) The LEVEL SET LED illuminates when an optimum operating level has

beenadjusted.

(3) The mono channels are equipped with a high-slope LOW CUT lter

eliminating unwanted low-frequency signals like rumble noise.

(4) PMP4000/PMP6000 (stereo channels): Press the A/B button to switch

from ¼" jacks to RCA connectors, and vice versa. Position “A” = ¼" jacks;

position“B” = RCA connectors.

(5) The HIGH control in the EQ section governs the high frequency range of the

respective channel.

(6) Use the MID control to boost or cut the midrange frequencies.

(7) PMP6000: The PMP6000 has an additional semi-parametric lter for the

midrange frequencies in the mono channels (tunable from 100 Hz to 8 kHz).

Adjust the boost/cut with the MID control, and the frequency with the

FREQcontrol.

The stereo channels contain a stereo EQ section. The cut-o frequencies

of the high and low bands are 12 kHz and 80 Hz respectively, while the

center frequencies of the high-mid and low-mid bands are 3 kHz and

400Hzrespectively.

(8) The LOW control allows you to boost/cut the low frequency range.

(9) With the MON(ITOR) control you can adjust the volume of each channel in

the monitor mix.

(10) The PMP4000 and PMP6000 feature a second MON control (MON 2) for the

volume of the second monitor bus.

(11) The FX control determines the signal level sent from each channel to the

built-in eects processor; this signal is also present at the FX SEND jack

(see (64)).

(12) The PMP6000 has two FX controls (FX 1 and FX 2), so that you can use two

eects simultaneously. Accordingly, the PMP6000 also has two eect aux

buses, which have one output jack in common (see (46) and (64)).

◊ ◊ Please note that the effects processor signal will be inaudible,

as long as the FX TO MON/MAIN controls (40), (41), (42) are set fully

counter-clockwise.

(13) The PAN(ORAMA) control determines the position of the channel signal in

the stereo main mix.

(14) The BAL(ANCE) control for the stereo channels corresponds to the PAN

control for the mono channels. It determines the relative volume of the left

and right input signals before they are routed to the stereo main output.

(15) PMP4000/PMP6000: When you press the PFL button (Pre Fader Listening)

the left LED (34) shows the pre-fader input gain of the channel. Adjustthe

optimum input gain (0 dB) with the GAIN control (1). When PFL is on,

thecorres ponding LED illuminates.

If the LEVEL SET LED (2) is illuminated constantly, the signal is within the

optimum operating level range. However, if the CLIP LED indicates that the

input gain is too high, you should reduce the level slightly with the GAIN

control. The CLIP LED should never be illuminated all the time, only with

signal peaks.

(16) The MUTE switch mutes the channel in the main mix. The pre-fader signals

(monitor buses) remain operative. When MUTE is pressed, the corresponding

control LED illuminates.

(17) The channel fader controls the channel signal level in the main mix.

2.1.1 Input section

(18) Each mono input channel is equipped with a balanced microphone input

(XLR connector) which provides +48 V phantom power for condenser

microphones at the touch of a button (see rear panel).

PMP1000: The two stereo channels 5/6 and 7/8 have an additional balanced

XLR microphone input with +48 V phantom power.

◊ ◊ Be sure to switch off your audio system before you activate the

phantom power supply to protect your monitor speakers from

switch-on thumps.

(19) Each mono input features one LINE IN connector (¼" jack), which can be used

with either balanced or unbalanced signals.

◊ ◊ Please remember to use either the microphone or the line input on a

specific channel. Never use both at the same time!

◊ ◊ When you connect a mono line signal to a stereo channel, always use

the left input. The mono signal will then be reproduced by both

sides equally.

9EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

◊ ◊ PMP1000: This does not apply to the mono/stereo combination

channels 5/6 and 7/8.

(20) INSERT I/O. Insert points or simply inserts are used to process a signal with

dynamic processors or equalizers. They are pre-fader, pre-EQ and pre-MON/

FX SEND. Unlike reverb and other eects, which are usually added to the dry

signal, dynamic processors usually process the entire signal. So, aux send

buses are not the best solution. Dynamic processors need to be inserted

directly into the signal path. Once processed, the signal then returns to the

mixing console at the same point where it left. Signal interruption takes

place only if a plug is inserted into the corresponding jack (¼" stereo plug:

tip = signal output, ring = input). All mono input channels are equipped

with inserts.

(21) The stereo channels have a GAIN control for gain adjustment, with the input

sensitivity ranging from +20 to -20 dB.

PMP1000: The stereo channels 5/6 and 7/8 feature an additional

XLRconnector for microphones whose gain can be set from 0 to +40 dB.

(22) Each stereo channel has two line-level inputs (¼" jacks) for the left and right

channels. If only the jack marked “L” is used, the channel is mono. The signal

will then be reproduced on both sides.

◊ ◊ PMP1000: This does not apply to the mono/stereo combination

channels 5/6 and 7/8.

◊ ◊ PMP1000: Channels 13/14 and 15/16 are routed to the main mix

without additional tone or volume adjustment. For example, using the

channels 13/14 and 15/16 you can connect a submixer and utilize the

PMP1000’s power amplifier.

(23) PMP4000: The stereo channels 9/10 and 11/12 are equipped with additional

RCA connectors.

PMP6000: The stereo channels 13/14 and 15/16 are equipped with additional

RCA connectors.

◊ ◊ PMP4000/PMP6000: Please note that you need to set the A/B selector

(4) to A (¼") or B (RCA) when you connect a signal to the input.

(24) PMP4000/PMP6000: Each of the two stereo channels has two monitor

controls (MON 1/2) and a LEVEL control (25). Like the other channels,

theyalso feature a PFL switch.

(25) Instead of a fader this channel has a rotary LEVEL control.

(26) The phantom power supply provides the voltage necessary for the operation

of condenser microphones. Use the PHANTOM switch to activate the supply

for the XLR connectors of the input channels. The +48 V LED will illuminate

when phantom power is on. In most cases, dynamic microphones can still be

used, as long as they are connected in a balanced conguration. If in doubt,

please contact the manufacturer of your microphone!

◊ ◊ With phantom power switched on, you must never connect

microphones to the console (or to a stage/wall box). Also, be sure to

mute the monitor/P.A. speakers, before you turn on the phantom

power supply. After switching on, please allow the system to stabilize

for about one minute, before you adjust the input gain.

◊ ◊ Caution! Never use unbalanced XLR connectors (pins 1 and 3

interconnected) on the MIC input jacks, if you are going to use the

phantom power supply.

(27) The AMP MODE switch determines the mode of operation of the

PMPamplier stage:

PMP1000:

MAIN: In the “MAIN” position the mixer works as a stereo amplier.

MON: In this mode the monitor signal is present at OUTPUT A (71) and the

main signal at OUTPUT B (70) (both are mono).

BRIDGE (bridged mono mode): In BRIDGE AMP MODE the output power

of OUTPUT A is added to that of OUTPUT B, i.e. OUTPUT B delivers twice its

normal output power.

PMP4000/PMP6000:

MAIN L/MAIN R. In position MAIN MIX, the mixer works as a

stereoamplier.

MON 1/MONO. In this mode the monitor 1 signal is present at OUTPUT A (71)

and the main signal at OUTPUT B (70) (both are mono).

BRIDGE (bridged mono mode): In BRIDGE AMP MODE the output power

of OUTPUT A is added to that of OUTPUT B, i.e. OUTPUT B delivers twice its

normal output power.

◊ ◊ In BRIDGE mode, always connect only one loudspeaker with an

impedance of at least 8 Ω to the OUTPUT B jack! Please note that

OUTPUT A must NEVER be used in BRIDGE mode!

◊ ◊ In all other operating modes, the minimum impedance of the speaker

must not fall below 4 Ω.

◊ ◊ Please note that the power delivered to the speaker connected to

OUTPUT B in BRIDGE AMP MODE is considerably higher than the power

provided to the speakers wired to the parallel speaker outputs.

Please read the information given on the rear panel of the power mixer.

◊ ◊ Information on how to properly connect your speaker with regard to

polarity can be found on the rear of the unit (PIN assignment)

(see also (71) and (42)).

(28) PMP6000: Use the Behringer SPEAKER PROCESSING switch to activate

a lter that allows you to adapt the mixer to the characteristics of your

loudspeakers. If the speakers have a limited frequency response in the bass

range, this function allows you to lter this range at the output signal of the

mixer and thus adapt it optimally to the frequency response of the speakers.

(29) PMP1000/PMP6000: If STANDBY is pressed, all input channels are muted.

During pauses you can prevent the microphones from picking up noise

or interference, which would then be reproduced by the P.A. system or

possibly damage the speaker diaphragms. The benet is that all faders can

be left untouched while you play back music from CD via the CD/TAPE inputs

(see(55)). There is also no need to move the faders and lose your mix.

2.2 Equalizer and FBQ

(30) Your power mixer features a graphic 7-band equalizer, which allows

you to ne-tune the sound depending on the room acoustics. In the

center position the frequency response is not eected. To boost or cut a

certain frequency range, simply move the corresponding fader upward or

downwardrespectively.

◊ ◊ Please note that the equalizer behaviour depends on the position of

the AMP MODE switch (see (27)).

10 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

(31) Press the FBQ IN switch to activate the Feedback Detection

system (the FBQ will be active only if you have switched on

the equalizer (33) before). Frequencies causing feedback are

shown by brightly lit fader LEDs. All other LEDs will be darker.

Now, cut the frequency range in question until feedback disappears (the LED

gets darker or goes out). This function is available for both the main and

monitor mix.

PMP1000: The switch FBQ FEEDBACK DETECTION performs the same

function as on the PMP4000 and PMP6000.

(32) Use the MAIN/MON 1 switch to select whether the equalizer processes the

main or the monitor mix. When not pressed, the stereo equalizer processes

only the main mix. When the switch is pressed, the EQ processes only the

monitor mix.

PMP1000: The MAIN MIX/MONITOR switch performs the same function as

on the PMP4000 and PMP6000.

(33) Press the EQ IN switch to activate the equalizer. The fader LEDs illuminate

when the EQ is on.

(34) Use this LED display to control the output level of the main signal. The upper

LIM LED illuminates when the internal amp protection circuit responds to

levels that are too high.

PMP1000: The POWER LED is illuminated when you switch the unit on.

◊ ◊ The LIM LEDs and the LED display do NOT light up when an external

signal is fed in via the PWR AMP INSERT jacks (61).

2.3 Eects section

(35) List of all multi-eects processor presets.

(36) The LED level meter on the eects module should always show a suciently

high level. Make sure that the Clip LED illuminates with signal peaks only. Ifit

is constantly illu-minated, the eects processor is overloading, which can

lead to unpleasant distortion. The FX SEND fader (PMP1000) or FX/FX 1/2

fader (PMP4000/PMP6000) controls the level sent to the eects module and

to the FX SEND output jacks.

(37) The eects display always reads the currently selected preset.

(38) PMP4000/PMP6000: Press the FX 1/2 IN switch to activate the

eectsprocessor.

(39) PMP1000/PMP4000: Turn the PROGRAM control to select an eects

algorithm (preset number starts ashing). Press this control to activate the

eect selected (PMP6000: FX 1/2 (PUSH)).

◊ ◊ PMP1000: The effects processor is operative all the time. Adjust the

effect intensity for the MAIN or MON signals with controls (40) or

(42) respectively.

PMP6000: The PMP6000 has two separate eects processors, which can be

used independently of one another. Enable one or both processors with the

FX1/2 IN (38) buttons.

(40) PMP4000/PMP6000: The FX 1/2 TO MON 1 control allows you to set the

intensity of the multi-eects processors in the monitor mix. No eect is sent

to the monitor mix when this control is set fully counter-clockwise.

PMP1000: The FX TO MON control performs the same function as on the

PMP4000 and PMP6000.

(41) The FX 1/2 TO MON 2 control allows you to determine the eect intensity

of the multi-eects processor in the monitor 2 mix. No eect is sent to the

monitor 2 mix with this control turned fully counter-clockwise.

(42) The FX 1/2 TO MAIN control allows you to determine the eect intensity of

the multi-eects processor in the main mix. No eect is sent to the main mix

with this control turned fully counter-clockwise.

PMP1000: The FX TO MAIN control performs the same function as on the

PMP4000 and PMP6000.

2.4 Main and monitor section

(43) The surround control determines the eect intensity.

This is a built-in eect, which widens the stereo

panorama, thus making the sound more lively

andtransparent.

(44) Press the XPQ TO MAIN switch to activate this eect.

(45) Pressing the AFL switch (after-fader listening) activates the solo function.

If AFL is on for the corresponding channel in the main section, you will only

hear the signal from this channel. Its volume can be adjusted with the fader.

Switching AFL on has no eect on the main or monitor mix, as long as you

don’t move the fader. In this way, you can monitor one or several selected

signals via the PHONES/CTRL jack (65). When AFL is on, the corresponding

control LED illuminates.

◊ ◊ The PMP1000 does not have an AFL function.

(46) PMP1000: FX SEND fader.

PMP4000: FX fader.

PMP6000: FX 1/2 fader.

This is the master send fader for the signal routed to the eects processor

and to the FX SEND output (63) (see also (11) and (12)).

(47) PMP1000: MON SEND fader.

PMP4000/PMP6000: MON 1/2 fader.

These faders are used to set the monitor output volume

(see also (9) and (10)).

(48) PMP1000: The main mix allows you to control the volume from the Main 1

output with both faders.

PMP4000/PMP6000: The MAIN 1 fader controls the volume of the

EUROPOWER. The main signal is also provided at the MAIN 1 output

(see also (58)).

(49) PMP4000/PMP6000: The MONO fader controls the mono mix signal

(see also (63)).

(50) PMP6000: The SUB FILTER lters out frequencies above the selected

setting, so that only low frequencies are sent to an (active) subwoofer via the

MONOOUT (63)). Set this switch to “On” to activate the lter.

(51) PMP6000: The SUB FREQ control determines the cut-o frequency for the

subwoofer output. This value can be adjusted from 30 to 200 Hz.

(52) The PHONS/CTRL R control adjusts the headphone or control room volume

(see also (65)).

(53) PMP4000/PMP6000: The MAIN 2 control determines the volume at the

MAIN 2 output (see also (59)), which is the same signal as at MAIN 1, but with

extra output jacks and separate volume control.

(54) PMP4000/PMP6000: With the CD/TAPE IN control you can adjust the

volume of the line signal present at the CD/TAPE INPUT (55). Use the PFL

switch to monitor the signal.

PMP1000: With the CD/TAPE RET fader you can adjust the line signal

applied to the CD/TAPE INPUT (55). Use the CD/TAPE MUTE switch to mute

thechannel.

11 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

2.4.1 Connectors

(55) Use the CD/TAPE INPUT jacks (RCA) to connect an external stereo signal,

such as a CD player, tape deck or other line-level sources.

(56) The VOICE CANCELLER lters vocal-specic frequencies from

the CD/TAPE INPUT signal. This function can be used for

karaoke, i.e. you can remove the vocals from a song and then

sing along with the music yourself.

(57) The CD/TAPE OUTPUT provides the line level stereo signal

(e.g. for a DATrecorder).

◊ ◊ If the CD/TAPE OUT signal is connected to a recording machine whose

output signal is returned to the CD/TAPE IN, feedback can occur

when you activate the record function on the recording machine.

So, disconnect the CD/TAPE IN from the recording machine before you

start recording or set the CD/TAPE input signal to zero!

(58) PMP1000: The MAIN OUT jacks allow you to send the main line level signal

to an external amplier, when, for example, you want to use the mixer

and eects section. The PMP4000 and PMP6000 have two separately

controllable line level MAIN outputs (59) (MAIN 1/2).

(60) Connect your monitor power amps or active monitor speakers to the

MON1/2 SEND to monitor the signal mix created with the MON controls or

to route it to the musicians on stage.

(61) The PMP Series comes with a POWER AMP INSERT connection that is

provided for various applications. This connection enables you to use the

power amplier of the device to amplify the output signal of another

preamp. For example, it is possible to connect a larger mixer or preamp

output (line signal) of an instrument amplier. In this case, you only need an

unbalanced, mono jack cable.

Furthermore, it is possible to use the POWER AMP INSERT as a conventional

insert to add a compressor or graphic equalizer to the signal path,

forinstance. Here, a balanced, stereo jack cable is required and the

assignment of tip and ring needs to be observed according to Figure4.5

(see Chapter 4.2 “Audio Connections”). In this case, the ring is the so-called

Send, which is connected to the input of the additional device, andthe

tip is referred to as Return, which is connected to the output of the

additionaldevice.

Lastly, it is possible to tap the output signal of the device’s mixer section

from the POWER AMP INSERT in order to use a second, external power

amp. A balanced, stereo jack cable is required with the ring (not the tip)

connectedto the input of the external power amp. If you want to use the

internal and external power amps at the same time, just wire the connector’s

ring and tiptogether.

(62) The FOOTSWITCH jack is for a standard footswitch. You can activate an

“eect bypass”, thereby muting the eects processor. Use a dual foot switch

for the PMP6000, so that you can enable/disable FX1 and FX2 independently

of each other. In this case, the tip of the ¼" plug controls FX1, and the

ringFX2.

(63) PMP4000/PMP6000: The MONO OUT is for connecting a subwoofer.

ThePMP6000 has the additional possibility of setting the low-frequency

range for the subwoofer.

Use the SUB FILTER control (50) to adjust the frequency.

(64) The FX SEND connector can be used to route the FX SEND signal from

the input channel, for example, to the input of an external eects

device. Sincethe PMP6000 has two FX controls per input signal (see (12)),

bothFXSEND 1+2 are present at one jack.

◊ ◊ Please note: The SEND signal is in parallel with the FX SEND jacks and

with the effects processor, so that both can be controlled together by

one control.

◊ ◊ For the FX signals, use a ¼" stereo plug connected as follows:

FX1 = tip; FX2 = ring

(65) The PHONS/CTRL connector allows you to connect a pair of stereo

headphones or an (active) monitor speaker.

2.5 Rear panel

(66) The mains connection is via a standard IEC receptacle. An appropriate power

cord is supplied with the unit.

(67) FUSE HOLDER. Before connecting the unit to the mains, ensure that

the voltage setting matches your local voltage. Blown fuses should only

be replaced by fuses of the same type and rating. Please also read the

information given in the “Specications”.

(68) Use the POWER switch to put your PMP into operation. The POWER switch

should always be in the “O” position before connecting your unit to

themains.

◊ ◊ Please note: The POWER switch does not fully disconnect the unit from

the mains. Unplug the power cord completely when the unit is not used

for prolonged periods of time.

(69) SERIAL NUMBER.

(70) This is where you nd the cooling fan of the unit.

The PMP6000 has two cooling fans.

(71) OUTPUT A (LEFT) provides either the left stereo main signal or the monitor

signal in mono, depending on the operating mode selected (see (27)).

NEVERuse this output in bridged mono mode.

(72) OUTPUT B (RIGHT/BRIDGE) provides either the right stereo main signal,

the main mix signal (mono) or the bridged mono signal, depending on the

operating mode selected.

◊ ◊ In BRIDGE mode always connect only one loudspeaker with an

impedance of at least 8 Ω to the OUTPUT B jack! NEVER use OUTPUT A in

BRIDGE mode!

◊ ◊ In all other operating modes the impedance of the connected

loudspeaker must not fall below 4 Ω.

3. Digital Eects Processor

24-BIT MULTI-EFFECTS PROCESSOR

This built-in eects module produces high-grade standard eects such as

reverb, chorus, anger, delay and various combination eects. The integrated

eects module has the advantage of requiring no wiring. This way, the danger

of creating ground loops or uneven signal levels is eliminated at the outset,

completely simplifying the handling. These eect presets are designed to be

added to dry signals.

◊ ◊ Turn down the FX controls in those channel strips whose signals you

don’t wish to process.

12 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Eect Presets of EUROPOWER PMP6000

No. EFFECT Description No. EFFECT Description

HALL 00-09 DELAY 50-59

00 SMALL HALL 1 approx. 1.0s reverb decay 50 SHORT DELAY 1 Like a short shattering

01 SMALL HALL 2 approx. 1.2s reverb decay 51 SHORT DELAY 2 1-2 short impulse(s)

02 SMALL HALL 3 approx. 1.5s reverb decay 52 SHORT DELAY 3 1-2 short impulse(s)

03 MID HALL 1 approx. 1.8s reverb decay 53 MID DELAY 1 Classical Delay for up-tempo music (115-125 BPM)

04 MID HALL 2 approx. 2.0s reverb decay 54 MID DELAY 2 Classical Delay for mid-tempo music (105-115 BPM)

05 MID HALL 3 approx. 2.5s reverb decay 55 MID DELAY 3 Classical Delay for slow-tempo music (95-105 BPM)

06 BIG HALL 1 approx. 2.8s reverb decay 56 LONG DELAY 1 Classical Delay for reggae-tempo music (85-95 BPM)

07 BIG HALL 2 approx. 3.2s reverb decay 57 LONG DELAY 2 Classical Delay for dub-tempo music (75-85 BPM)

08 BIG HALL 3 approx. 4s reverb decay 58 LONG DELAY 3 Extra long (nearly innite) delay eect

09 CHURCH approx. 7s reverb decay 59 LONG ECHO Extra long canyon echo eect

ROOM 10-19 CHORUS 60-69

10 SMALL ROOM 1 approx. 0.5s reverb decay 60 SOFT CHORUS 1 Unobtrusive eect

11 SMALL ROOM 2 approx. 0.8s reverb decay 61 SOFT CHORUS 2 Unobtrusive eect with dierent color

12 SMALL ROOM 3 approx. 1.0s reverb decay 62 WARM CHORUS 1 Analog sounding

13 MID ROOM 1 approx. 1.2s reverb decay 63 WARM CHORUS 2 Analog sounding with dierent color

14 MID ROOM 2 approx. 1.5s reverb decay 64 PHAT CHORUS 1 Pronounced chorus eect

15 MID ROOM 3 approx. 1.8s reverb decay 65 PHAT CHORUS 2 Pronounced chorus eect with dierent color

16 BIG ROOM 1 approx. 2.0s reverb decay 66 CLASSIC FLANGER Standard anger eect

17 BIG ROOM 2 approx. 2.2s reverb decay 67 WARM FLANGER More analog touch

18 BIG ROOM 3 approx. 2.5s reverb decay 68 DEEP FLANGER Deep modulation impression

19 CHAPEL approx. 3s reverb decay 69 HEAVY FLANGER Extremely pronounced eect

PLATE 20-29 PHASE/PITCH 70-79

20 SHORT PLATE approx. 1.0s reverb decay 70 CLASSIC PHASER Standard phaser eect

21 MID PLATE approx. 1.5s reverb decay 71 WARM PHASER More analog touch

22 LONG PLATE approx. 2.2s reverb decay 72 DEEP PHASER Deep modulation impression

23 VOCAL PLATE approx. 1.2s reverb decay 73 HEAVY PHASER Extreme strong eect

24 DRUMS PLATE approx. 1.0s reverb decay 74 PITCH SHIFT DETUNE 2-3-times detune for a wider solo voice sound

25 GOLD PLATE 1 approx. 1.2s reverb decay 75 PITCH SHIFT +3 Minor third added voice

26 GOLD PLATE 2 approx. 2.0s reverb decay 76 PITCH SHIFT +4 Major third added voice

27 SHORT SPRING approx. 1.0s reverb decay 77 PITCH SHIFT +7 Quint above added voice

28 MID SPRING approx. 2.0s reverb decay 78 PITCH SHIFT -5 Fourth down added voice

29 LONG SPRING approx. 2.5s reverb decay 79 PITCH SHIFT -12 1 octave down added voice

GATED/REVERSE 30-39 MULTI 1 80-89

30 GATED REV SHORT approx. 0.8s gate time 80 CHORUS + REVERB 1 Soft chorus + medium-short reverb

31 GATED REV MID approx. 1.2s gate time 81 CHORUS + REVERB 2 Deep chorus + medium-long reverb

32 GATED REV LONG approx. 2.0s gate time 82 FLANGER + REVERB 1 Soft anger + medium-short reverb

33 GATED REV XXL approx. 3.0s gate time 83 FLANGER + REVERB 2 Deep anger + medium-long reverb

34 GATED REV DRUMS 1 approx. 0.8s gate time 84 PHASER + REVERB 1 Soft phaser + medium-short reverb

35 GATED REV DRUMS 2 approx. 1.2s gate time 85 PHASER + REVERB 2 Deep phaser + medium-long reverb

36 REVERSE SHORT approx. 0.8s reverb raise 86 PITCH + REVERB 1 Soft voice detuning + medium-short reverb

37 REVERSE MID approx. 1.2s reverb raise 87 PITCH + REVERB 2 Fourth above interval + medium-long reverb

38 REVERSE LONG approx. 2.0s reverb raise 88 DELAY + REVERB 1 Short delay + medium-short reverb

39 REVERSE XXL approx. 3.0s reverb raise 89 DELAY + REVERB 2 Medium-long delay + medium-long reverb

EARLY REFLECTIONS 40-49 MULTI 2 90-99

40 EARLY REFLECTION 1 Short 90 DELAY + GATED REV Short delay + medium-long gated reverb

41 EARLY REFLECTION 2 Medium-short 91 DELAY + REVERSE Medium-short delay + medium-long reverse reverb

42 EARLY REFLECTION 3 Medium-long 92 DELAY + CHORUS 1 Short delay + soft chorus

43 EARLY REFLECTION 4 Long 93 DELAY + CHORUS 2 Medium-long delay + deep chorus

44 SHORT AMBIENCE Short 94 DELAY + FLANGER 1 Short delay + soft anger

45 MID AMBIENCE Medium-short 95 DELAY + FLANGER 2 Medium-long delay + deep anger

46 LIVE AMBIENCE Medium-short 96 DELAY + PHASER 1 Short delay + soft phaser

47 BIG AMBIENCE Medium-long 97 DELAY + PHASER 2 Medium-long delay + deep phaser

48 STADIUM Long 98 DELAY + PITCH 1 Short delay + fourth down interval

49 GHOST AMBIENCE Extra-long special FX 99 DELAY + PITCH 2 Medium-long delay + minor third above interval

13 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

4. Installation

4.1 Mains connection

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certication requirements.

Blown fuses must be replaced by fuses of the same type and rating.

◊ ◊ Please make sure that all units have a proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or of the AC power cord.

4.2 Audio connections

The inputs and outputs of your Behringer EUROPOWER are unbalanced ¼" mono

jacks—except for the mono channel line inputs, which are balanced ¼" stereo

jacks. Of course, all inputs and outputs work with both balanced and unbalanced

connectors. The tape in and outputs are on RCA connectors.

◊ ◊ Please ensure that only qualified personnel install and operate the

PMP. During installation and operation, the user must have sufficient

electrical contact to earth. Electrostatic charges might affect the

operation of the unit.

strain relief clamp

sleeve

tip

sleeve

(ground/shield)

Unbalanced ¼" TS connector

tip

(signal)

Fig. 4.1: ¼" TS connector

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

For connection of balanced and unbalanced plugs,

ring and sleeve have to be bridged at the stereo plug.

Balanced ¼" TRS connector

ring

cold (-ve)

tip

hot (+ve)

Fig. 4.2: ¼" TRS connector

output

For unbalanced use, pin 1 and pin 3

have to be bridged

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

input

Balanced use with XLR connectors

Fig. 4.3: XLR connectors

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

¼" TRS footswitch connector

ring

FX2

tip

FX1

Fig. 4.4: ¼" mono plug for footswitch

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

Connect the insert send with the input and the insert with

the output of the output eects device.

Power amp insert send return ¼" TRS connector

ring

send (out)

tip

return (in)

Fig. 4.5: Stereo ¼" TRS connector for power amp ISR connection

14 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

4.3 Loudspeaker connections

Your power mixer is equipped with high-quality loudspeaker connectors ,

whichensure safe and trouble-free operation. The connector was especially

developed for high-power loudspeakers. Once it is plugged in, it safely locks into

position and cannot be accidentally disengaged. It prevents the occurrence of

electrical shock and ensures the correct polarity. Each of the loudspeaker jacks

carries only the assigned single signal (see the information given on the rear

panel of the power mixer).

1- 2-

front view rear view

Professional speaker connector

(compatible with Neutrik Speakon connectors)

Fig. 4.6: Professional speaker connector with polarity allocation

Please be sure to only use commercial cables (type NL4FC) for connecting your

loudspeakers to the power mixer. Please check the pin assignment of your

loudspeakers and cables dependent on the PMP speaker output you choose.

EUROPOWER PMP6000/PMP4000/PMP1000

OUTPUT A 1+ 1- 2+ 2-

MAIN L x x

MONITOR x x

MONO x x

OUTPUT B x x

OUTPUT B 1+ 1- 2+ 2-

MAIN R x x

MONO x x

BRIDGE x x

Tab. 4.1: Polarity conguration of speaker connectors

OUTPUT B

BRIDGE

1- 1-

8 Ω

4 Ω

8 Ω

4 Ω

16 Ω

8 Ω

OUTPUT B

Fig. 4.7: Pin assignment

5. Wiring Examples

Fig. 5.1: Stereo operation

Loudspeaker connection (monitor mix)

PMP1000

PMP4000

PMP6000

(part view)

2 x BEHRINGER EUROLIVE Stack

(B1800X & B1220, both passive)

2 x BEHRINGER F1220D

(active)

front panel (part view)

Footswitch Link Output

For stereo operation the POWER AMP switch (27) must be set to its upper position

(MAIN or MAIN L/MAIN R). Outputs A and B provide the stereo main signal for

passive speakers. The preamp monitor output is connected to two parallel active

speakers, which are used as on-stage monitors. Use the footswitch to enable/

disable the eects processor.

15 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Fig. 5.2: Bridged mono operation

Subwoofer

PMP1000

PMP4000

PMP6000

Rear panel

EUROPOWER EP2000

EUROLIVE

VP1520

EUROLIVE B1800X

Subwoofer

2 x BEHRINGER F1220D

(active)

F.O.H. mix Monitor mix

This illustration shows the power mixer with a sub-woofer connected to

OUTPUTB. For a bridged mono operation to OUTPUTB, the AMP MODE selector

switch (27) must be set to its lower position “BRIDGE”. A separate stereo power

amp (Behringer EUROPOWER EP2000) connected to the preamp main outputs

delivers the stereo main signal. Two active monitor speakers for on-stage

operation are connected to the preamp monitor output.

Fig. 5.3: Dual mono operation

Loudspeaker connection for F.O.H and monitor mix (mono)

PMP1000/PMP4000/PMP6000

Rear panel (excerpt)

2 x BEHRINGER EUROLIVE VP1520

(passive)

2 x BEHRINGER

EUROLIVE VP1220F

(passive)

For a dual mono operation, the AMP MODE switch (27) must be set to its center

position (MON1/MONO for PMP4000/PMP6000 or MON for PMP1000)! The two

loudspeaker outputs provide the main and the monitor signals, separately from

each another. Each of these signals is then sent to two speakers wired in parallel.

16 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Fig. 5.4: Standard set-up (example)

ULTRA-G GI100

Electric bass

Vocal mics

Mono

channels 1-4

Mono

channel 5

Mono

channel 6

CD player

DAT recorder

Stereo

channel

13/14

Electric guitar

V-AMP2

Keyboard

CD/tape

out

The illustration shows just one channel conguration possible, comprising mono

and stereo sources and additionally the tape input/output for recording the mix

signal or feeding in a playback signal.

17 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Fig. 5.5: Expanded set-up

BEHRINGER EUROLIVE VP1220 BEHRINGER EUROLIVE VP1220

BEHRINGER

EUROLIVE B1800X

BEHRINGER

EUROLIVE B1800X

PMP1000/PMP4000/

PMP6000 Rear panel

Output B

Vocals/voice

BEHRINGER

XM1800S

BEHRINGER B-2 PRO

Keyboard

Drum Computer

BEHRINGER

V-AMP 3

Electric guitar

Electric bass

BEHRINGER

BASS V-AMP

CD-Player

CD/TAPE IN

CD/TAPE OUT

DAT-Recorder

Passive monitors

BEHRINGER EUROLIVE

VP1220F IEM

(In-Ear-Monitoring)

BEHRINGER

HPS3000

BEHRINGER

EUROPOWER EP2000

MON 1/2 OUT

Headphone amplier

BEHRINGER POWERPLAY

PRO-XL HA4700

Stereo inputs

PHONS/CTRL OUT

Drums/percussion BEHRINGER

EUROPOWER EP2000

MAIN 1 OUT

B1800-Pro Active

Subwoofer

MONO

OUT

Output A

This application is an expanded set-up based on the standard set-up as shown

in g. 5.4, and provides additional connection options. Again, this is just an

example, which can be expanded in various ways.

18 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

6. Specications

PMP6000

Microphone Inputs

Type XLR, electronically balanced input circuit

Mic E.I.N. (20 Hz - 20 kHz)

@ 0 Ohm source resistance -134 dB / 136 dB A-weighted

@ 50 Ohm source resistance -131.5 dB / 134 dB A-weighted

@ 150 Ohm source resistance -129 dB / 155 dB A-weighted

Frequency response < 10 Hz - 200 kHz (-1 dB)

< 10 Hz - > 200 kHz (-3 dB)

Gain +10 dB, +60 dB

Max. input level +12 dBu @ +10 dB gain

Impedance approx. 2.6 kOhm balanced

approx. 1.3 kOhm unbalanced

Signal-to-noise ratio 109 dB / 112 dB A-weighted

(0 dBu In @ +10 dB gain)

Noise (THD + N) 0.002% / 0.0018% A-weighted

Mono Line Inputs

Type ¼" TS connectors, balanced

Impedance approx. 20 kOhm

Max. input level +21 dBu

Stereo Line Inputs

Type ¼" TRS connectors, unbalanced

Impedance > 3.6 kOhm

Max. input level +22 dBu

Equalizer

Low 80 Hz / ±15 dB

Mid 100 Hz - 8 kHz / ±15 dB

High 12 kHz / ±15 dB

2 Track Input

Type RCA

Impedance approx. 3.6 kOhm

Preamp Outputs

MAIN

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

Monitor

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

Stereo Outputs

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. input level +21 dBu

Type RCA

Impedance approx. 1 kOhm

Max. input level +21 dBu

Loudspeaker Outputs

Type Professional locking connector

Load Impedance:

MAIN L/R 4 - 8 Ohm

MONITOR/MAIN MONO 4 - 8 Ohm

MAIN MONO/MAIN MONO 4 - 8 Ohm

BRIDGE 8 - 16 Ohm

DSP

Converter 24-bit Delta-Sigma,

64/128-times oversampling

Dynamics D/A 90 dB

Sampling rate 46.875 kHz

Delay Time max. 5 secs

Signal run time approx. 1.5 ms (Line In > Line Out)

Display

Type 2 x 2-digit, 7-segment LED

19 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Output Power

RMS @ 1% THD, Both Channels Driven:

8 Ohm per channel 300 W

4 Ohm per channel 600 W

RMS @ 1% THD, Bridged Mode:

8 Ohm 1200 W

Peak Power, Both Channels Driven:

8 Ohm per channel 400 W

4 Ohm per channel 800 W

Peak Power, Bridged Mode:

8 Ohm 1,600 W

Power Supply

Mains Voltage

USA/Canada 120 V~, 60 Hz

China/Korea 220 V~, 50/60 Hz

Europe/Australia 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

Fuse 100 - 120 V~ T 10 A H 250 V

Fuse 220 - 240 V~ T 6.3 A H 250 V

Power Consumption

Power consumption 1,050 W

Mains connector IEC standard receptacle

Dimensions/Weight

Dimensions (H x W x D) 4.8 x 19.5 x 23.5"

122 x 496 x 596 mm

Weight 28.9 lbs / 13.1 kg

PMP4000

Microphone Inputs

Type XLR, electronically balanced input circuit

Mic E.I.N. (20 Hz - 20 kHz)

@ 0 Ohm source resistance -134 dB / 136 dB A-weighted

@ 50 Ohm source resistance -131.5 dB / 134 dB A-weighted

@ 150 Ohm source resistance -129 dB / 155 dB A-weighted

Frequency response < 10 Hz - 200 kHz (-1 dB)

< 10 Hz - > 200 kHz (-3 dB)

Gain +10 dB, +60 dB

Max. input level +12 dBu @ +10 dB gain

Impedance approx. 2.6 kOhm balanced

approx. 1.3 kOhm unbalanced

Signal-to-noise ratio 109 dB / 112 dB A-weighted

(0 dBu In @ +10 dB gain)

Noise (THD + N) 0.002% / 0.0018% A-weighted

Mono Line Inputs

Type ¼" TS connectors, balanced

Impedance approx. 20 kOhm

Max. input level +21 dBu

Stereo Line Inputs

Type ¼" TRS connectors, unbalanced

Impedance > 3.6 kOhm

Max. input level +22 dBu

Equalizer

Low 80 Hz / ±15 dB

Mid 2.5 kHz / ±15 dB

High 12 kHz / ±15 dB

2 Track Input

Type RCA

Impedance approx. 3.6 kOhm

20 EUROPOWER PMP6000/PMP4000/PMP1000 User Manual

Preamp Outputs

MAIN

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

Monitor

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

Stereo Outputs

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. input level +21 dBu

Type RCA

Impedance approx. 1 kOhm

Max. input level +21 dBu

Loudspeaker Outputs

Type Professional locking connector

Load Impedance:

MAIN L/R 4 - 8 Ohm

MONITOR/MAIN MONO 4 - 8 Ohm

MAIN MONO/MAIN MONO 4 - 8 Ohm

BRIDGE 8 - 16 Ohm

DSP

Converter 24-bit Delta-Sigma,

64/128-times oversampling

Dynamics D/A 90 dB

Sampling rate 46.875 kHz

Delay Time max. 5 secs

Signal run time approx. 1.5 ms (Line In > Line Out)

Display

Type 2-digit, 7 segment LED

Output Power

RMS @ 1% THD, Both Channels Driven:

8 Ohm per channel 300 W

4 Ohm per channel 600 W

RMS @ 1% THD, Bridged Mode:

8 Ohm 1200 W

Peak Power, Both Channels Driven:

8 Ohm per channel 400 W

4 Ohm per channel 800 W

Peak Power, Bridged Mode:

8 Ohm 1,600 W

Power Supply

Mains Voltage

USA/Canada 120 V~, 60 Hz

China/Korea 220 V~, 50/60 Hz

Europe/Australia 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

Fuse 100 - 120 V~ T 10 A H 250 V

Fuse 220 - 240 V~ T 6.3 A H 250 V

Power Consumption

Power consumption 1,050 W

Mains connector IEC standard receptacle

Dimensions/Weight

Dimensions (H x W x D) 4.8 x 18.1 x 18.7"

122 x 460 x 476 mm

Weight 22.9 lbs / 10.4 kg

Page is loading ...

Behringer PMP1000 Owner's manual

Brand: Behringer

Model: PMP1000

Category: Audio mixers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Behringer PMP1000 Owner's manual

This manual is also suitable for

Behringer PMP1000 Owner's manual

Related papers

Other documents