Symmons SRT-4470 Installation guide

Brand: Symmons

Model: SRT-4470

Type: Installation guide

This manual is also suitable for

SRT-4470-STN

Symmons SRT-4470 is a Roman tub faucet with a variety of features that make it a great choice for any bathroom. The faucet is made of durable materials and is designed to last for years. It has a classic design that will complement any bathroom décor. The faucet is easy to install and comes with all the necessary hardware.

The Symmons SRT-4470 has a number of features that make it a great choice for any bathroom. The faucet has a flow rate of 2.5 gallons per minute, which is ideal for filling a tub quickly. The faucet also has a spray function, which is great for rinsing off soap or shampoo. The faucet is also equipped with a diverter, which allows you to switch between the tub spout and the handheld showerhead.

Installation Procedure:

1. Drill three 1 1/4” holes into the deck (maximum deck

thickness 1-3/8” ).

2. Cut 1/2” copper tubing (RT-108) to length required.

Example: If a 10” valve center to valve center is required,

the tubing should be cut to 3 7/8”. e maximum overall

center to center dimension with supplied tubing is

18-1/4”.

For greater widths the installer will need to provide their

own tubing.

3. Ensure the centerbody nut (RT-103N) is threaded onto

the centerbody (RT-100) and then install 3/8” plug (RT-

105).

Solder the branch of the tee (HPT-10) to the centerbody.

Cut to proper length and solder the two 1/2” copper

tubing (RT-108) into the run of the tee (HPT-10) and

into the valve bodies (RT-103).

4. Push assembly through deck holes from the bottom with

hot on le.

Slip retaining plate (RT-101) over the centerbody (RT-

100) making sure the retaining plate (RT-101) slides over

the ange of the centerbody.

en turn the retaining plate 90 degrees under the

nut on the centerbody (RT-100) to hold in place. e

soldered assembly should be held in position on the

deck making sure the hot cartridge is on the le.

Ensure the tops of the valve bodies measure

approximately 1-7/8” from the nished deck by

adjusting centerbody and valve body nuts (RT-103N).

Note: If tile or nished surface will be installed while

the plumbing is in a “roughed in state” the retaining

plate (RT-101) should be shimmed the thickness of the

nishing material.

5. Tighten the centerbody nut (RT-103N) under the deck.

read valve body nuts (RT-103N) up to base of deck

but do not tighten.

6. Solder 1/2” hot and cold supplies to valve bodies

(RT-103).

7. e system can be tested at this time.

Remove plug (RT-105) when the spout (RT-135) is to be

assembled onto the faucet.

8. Grease o-ring (T-2) in the bore of the spout.

Assemble spout onto centerbody with gasket (RT-165)

under the spout.

Tighten spout (RT-135) in place with set screw

(SC-15A).

Important: O-ring (T-2) can be damaged if set screw

(SC-15A) is overtightened during installation. If faucet

begins to leak from under spout, replace o-ring (T-2).

9. read handle escutcheons (RT-104) onto valve bodies.

read collar (LN-112) onto the valve body until it

reaches the escutcheons (RT-104).

Tighten three body nuts (RT-103N) securely.

10. Faucet handle installation:

Place handle on valve spindle and thread screw

(LN-121A) into valve.

11. It is very important to thoroughly ush the supply lines

to prevent foreign matter, i.e. copper chips, sand, stones,

etc. from damaging the sealing surfaces of cartridge.

Remove aerator and open hot and cold to full open then

open both supplies.

Let water run through hot and cold long enough to ush

supply lines thoroughly.

Shut o faucet and replace aerator. Check for leaks.

Cartridge Replacement (KN-113 or KN-114)

1. Remove plug button (LN-243C or LN-243H), loosen

Philip head screw (LN-121A) and remove handle (LN-

177).

2. Remove collar (LN-112) by turning counter clockwise.

Caution: Do not use wrench as this may damage the

surface nish.

3. Place wrench on cartridge hex nut (KN-113, KN-114).

Turn wrench counter clockwise until cartridge is

removed.

4. Install new cartridge. Turn cartridge with wrench until

cartridge does not turn easily then turn 1/4 to 1/2 turn

further. Reassemble handle in reverse fashion.

Roman Tub Faucet SRT-4470

Installation and Service Instructions

Carrington®

Caution: Be sure to turn off hot and cold water supplies before

installing or servicing faucet.

Compliance: ASME A112.18.1/CSA B125.1

Note: Dimensions subject to change without notice.

2-1/2"

(62 mm)

2-1/4"

(58 mm)

(153 mm)

9-1/2" (241 mm)

(102 mm)

1-7/8"

(48 mm)

9-7/8"

(252 mm)

2-1/4" dia

(57 mm)

3" dia (76 mm)

1-1/2"

(38 mm)

Hole size

1-1/8" (29 mm) min

1-3/8" (35 mm) max

Deck thickness

1-3/8" (35 mm) max

10-1/8" (259 mm)

8º

connection for

1/2 inch copper tube

Dimensions Carrington Roman Tub Faucet, SRT-4470

HPT-10 1/2” Copper Tee

KN-113 Valve cartridge, cold

KN-114 Valve cartridge, hot

LN-112* Collar (lever handle) (2)

LN-121A* Oval Philips head screw (2)

LN-177* Cross handle (2)

RT-100 Centerbody

RT-101 Plate, Retaining

RT-103 1/2” Valve body (2)

RT-103N Nut (3)

RT-104 Escutcheon (2)

RT-105 Plug, 3/8” NPT Brass

RT-108 Tubing, 1/2” (2)

RT-116 Gasket, Escutcheon (2)

RT-135 Spout

RT-165-PL Ring

SC-15 Set screw (spout)

T-2 O-ring (spout)

T-288 Plug Button (spout)

RT-CRP-KIT* Handle kit (hot & cold handles)

*For Decorative Finish Faucets add sufx to

parts marked with an asterisk as follows:

Sufx STN: Satin Nickel nish

KN-114

hot indicator

T- 2

RT-105

RT-101

RT-100

HPT-10

RT-108

RT-103

cold indicator

Dimensions Carrington Roman Tub Faucet, SRT-4470

RT-103N

Handle kit

(qty 2 handles)

LN-243H (1) LN-243C (1)

L-26 (2)

LN-121A (2)

LN-177 (2)

LN-112 (2)

RT-104 (2)

RT-116 (2)

T-288

SC-15

RT-135

RT-165-PL

KN-113

RT-103N

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects,

or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Symmons SRT-4470 Installation guide

Brand: Symmons

Model: SRT-4470

Type: Installation guide

This manual is also suitable for

SRT-4470-STN

Download PDF

report

Symmons SRT-4470 Installation guide

This manual is also suitable for

Symmons SRT-4470 Installation guide

Related papers

Other documents