ThermoMart 220V kiln plug and play Owner's manual

Brand
ThermoMart
Model
220V kiln plug and play
Type
Owner's manual

This manual is also suitable for

ThermoMart 220V kiln plug and play

The ThermoMart 220V kiln plug and play is a versatile and reliable device that can be used for a variety of applications, including:

  • Kiln control: The ThermoMart 220V kiln plug and play can be used to control the temperature of a kiln. This is ideal for potters, glass blowers, and other artists who need to precisely control the temperature of their kilns.
  • Temperature monitoring: The ThermoMart 220V kiln plug and play can also be used to monitor the temperature of a kiln. This is useful for ensuring that the kiln is operating at the correct temperature and for troubleshooting any problems that may occur.

ThermoMart 220V kiln plug and play

The ThermoMart 220V kiln plug and play is a versatile and reliable device that can be used for a variety of applications, including:

  • Kiln control: The ThermoMart 220V kiln plug and play can be used to control the temperature of a kiln. This is ideal for potters, glass blowers, and other artists who need to precisely control the temperature of their kilns.
  • Temperature monitoring: The ThermoMart 220V kiln plug and play can also be used to monitor the temperature of a kiln. This is useful for ensuring that the kiln is operating at the correct temperature and for troubleshooting any problems that may occur.
Plug & play Temperature Controller Box 220V – 30Amp (www.thermomart.com)
Wiring and installation
Before attempting installation or service all power to the system must be disconnected/Off (from
the circuit breaker and/or any other power supplying sources). The device must be installed by a
QUALIFIED PROFESSIONAL.
Using the provided key, please gently open the box and install the cable glands as well as the
thermocouple gland (the smaller gland with thermocouple extension passing through it) on your
box and connect the male connector of the thermocouple to the female connector of
thermocouple wire extension. Then by loosening the 2 nuts on the panel mount of the terminals
box gently bring out the panel mount (be careful to not pull the wires inside the box). This
controller box should be placed between the 220V receptacle on the wall and your kiln. For easy
wiring, you need to cut your kiln cable in 2 halves. Bring out the 2 hot lines, neutral and ground
wires from the cable jacket of each end and then start with first hotline (black - H1) and connect
the hotline of one half to pole1 of terminal (loosen the screw and put the wire under the
terminal) and the black hotline of the other half (output) to the same pole in the other side. Do
the same with other hotline (Red), Neutral (white) and Ground (green) wires too. For more
clarification please check the following diagram.
After wiring, put back the terminal panel mount and tighten the nuts as well as the input and
output glands and slowly close the control box door. Make sure the wires are inside the box and
far from the SSRs.
This controller box is equipped with the following items:
1- Circuit breaker on the box. It will turn your controller ON/OFF and also protects the controller
and your kiln against overloading of more than 30 Amps.
2- The turn ON/OFF switch for 2 fans. The fans cool down the controller box during operation.
The fans must turn ON when you run your kiln and OFF when kiln work is finished and is OFF.
3- The alarm switch and LED light on the box. Turn this switch ON if you program the controller
to use the alarm feature. When the temperature passes the alarm limits, both the LED light and
the alarm sound will come ON.
4- A temperature/humidity display on the box for monitoring these parameters inside the box.
5- Manual of the temperature controller.
  • Page 1 1

ThermoMart 220V kiln plug and play Owner's manual

Brand
ThermoMart
Model
220V kiln plug and play
Type
Owner's manual
This manual is also suitable for

ThermoMart 220V kiln plug and play

The ThermoMart 220V kiln plug and play is a versatile and reliable device that can be used for a variety of applications, including:

  • Kiln control: The ThermoMart 220V kiln plug and play can be used to control the temperature of a kiln. This is ideal for potters, glass blowers, and other artists who need to precisely control the temperature of their kilns.
  • Temperature monitoring: The ThermoMart 220V kiln plug and play can also be used to monitor the temperature of a kiln. This is useful for ensuring that the kiln is operating at the correct temperature and for troubleshooting any problems that may occur.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents