meitav-tec ETN-24-PM2-3S Product information

Brand
meitav-tec
Model
ETN-24-PM2-3S
Type
Product information

meitav-tec ETN-24-PM2-3S is a programmable thermostat that has several features and functions to help you control the temperature of your home or office.

This thermostat has three fan speeds: low, medium, and high, as well allowing you to set custom fan speeds.

It also has an adjustable open/close time for the motor, ranging from 10-400 seconds, with a default of 60 seconds.

The thermostat can be set to either heat or cool mode, and it has an auto change-over function that will switch between modes automatically based on the temperature.

The thermostat also has a number of other features, including:

meitav-tec ETN-24-PM2-3S is a programmable thermostat that has several features and functions to help you control the temperature of your home or office.

This thermostat has three fan speeds: low, medium, and high, as well allowing you to set custom fan speeds.

It also has an adjustable open/close time for the motor, ranging from 10-400 seconds, with a default of 60 seconds.

The thermostat can be set to either heat or cool mode, and it has an auto change-over function that will switch between modes automatically based on the temperature.

The thermostat also has a number of other features, including:

ETN24-PM2-3S
G3G2G1
CL1
Technician Settings
Adjust the Open/Close time for the motor.
The Open/Close time of the motor can be adjusted by the technician, according
to the motor specifications. Adjustable range: 10-400 seconds, Default 60 seconds.
Use DIP switch S1.4 to switch between normal mode and technician mode.
- Move DIP switch S1.4 to ON position.
- Adjust the Open/Close time using the [+] or [-] buttons according to the following equation:
Time (seconds) = ( 1 ÷ 40 ) X 10 example: 30 30 X 10 = 300 seconds.
- Move DIP switch S1.4 back to OFF position.
Internal / External sensor.
Use DIP Switches S1.1, S1.2 and S1.3 to select between Internal and External sensor configuration as follows:
Internal sensor (default): S1.1, S1.3 – ON, S1.2 – OFF
External sensor: S1.1, S1.3 – OFF, S1.2 – ON
Offset for calibration of measured temperature
- Adjust the set point temperature to 10°C.
- Press and hold the [Mode] button for more than 15 seconds.
- Adjust the offset using the [+] and [-] buttons – range (-6)…(+6)°C.
- Press the [Mode] button again to return to normal display.
Note:
- DIP Switches 5 and 6 are not in use (OFF position)
- The two jumpers standing on the left side of the DIP switch must be in Pos.1 – two upper legs short
Operating Manual
On/Off
- Press the [On/Off] button to activate or deactivate the thermostat. The words "ON" or "OFF" will appear on display.
Set point temperature
- Press the [+] or [-] buttons – the set point temperature will flash.
- Adjust the set point temperature using the [+] or [-] buttons.
Modes
- Press the [Mode] button to switch between modes:
- Cool – “Cool” will appear on display. “Cool” will flash when cooling active.
- Heat – “Heat” will appear on display. “Heat” will flash when heating active.
- Auto change-over – “Cool” and “Heat” will appear on display. The active mode will flash.
Fan speeds
- Press the [Fan] button to switch between modes:
- Low speed – “Lo” will appear on display.
- Medium speed – “Me” will appear on display.
- Hi speed – “Hi” will appear on display.
- Auto speed – “Lo”, “Me” and “Hi” will appear on display. The active speed will flash.
RC
COM
Common
24VAC
Main
input
Fan
°C
ModeOn/Off
SET
Cool
OP1
Date:
Title:
1 Original 25.04.05 File name: etn24-pm2-3s.vsd
Drawn: P.Rechtman
Checked: Y.Podkovirin
Approved: E.Roy
ETN24-PM2-3S
16.02.09
meitav-tec
Tel: Tel: +972-3-9626462
Fax: +972-3-9626620
email: [email protected]
Print name: ETN24-PM2
Print: ETN24-PM-3S-3H 225.06.07
CL2OP2
Open
Close
Open
Close
Cool
24VAC
3-wire
Heat
24VAC
3-wire
Low
High
Medium
Fan speeds
24VAC
Heat Hi
Me
Lo
ON
OFF
ON
123456
ON
123456
Technician mode Normal mode
ON
123456
Internal sensor External sensor
ON
123456
Software: EPM2S36
Checksum: F5D8
New print: ETN24-PM2 Rev.B3 16.02.09
T0
Not in use
External sensor
  • Page 1 1

meitav-tec ETN-24-PM2-3S Product information

Brand
meitav-tec
Model
ETN-24-PM2-3S
Type
Product information

meitav-tec ETN-24-PM2-3S is a programmable thermostat that has several features and functions to help you control the temperature of your home or office.

This thermostat has three fan speeds: low, medium, and high, as well allowing you to set custom fan speeds.

It also has an adjustable open/close time for the motor, ranging from 10-400 seconds, with a default of 60 seconds.

The thermostat can be set to either heat or cool mode, and it has an auto change-over function that will switch between modes automatically based on the temperature.

The thermostat also has a number of other features, including:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents