Sony CFD-S28L Operating instructions

Category
CD players
Type
Operating instructions

This manual is also suitable for

3-866-937-21 (1)
1999 by Sony Corporation
CD Radio
Cassette-Corder
GB
Operating Instructions page 2
GB
Manual de instrucciones página 2
ES
ES
CFD-S28L
CFD-S38
CFD-S38L
Introduction2
GB
Warning
To prevent fire or shock hazard, do
not expose the player to rain or
moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to
qualified personnel only.
Information
For customers in Europe
This Compact Disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is
located on the bottom exterior.
Warning
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Notice for customers in the United
Kingdom
A moulded plug complying with BS 1363 is
fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced, same rating fuse approved by
ASTA or BSI to BS 1362, (i.e. marked with
or mark) must be used.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never
use the plug without the fuse cover. If you
should lose the fuse cover, please contact
your nearest Sony service station.
About this manual
The instructions in this manual are for the
CFD-S28L, CFD-S38 and CFD-S38L. Before
you start reading, check your model number.
The CFD-S38L is the model used for
illustration purpose.
Note
The name of the switch to turn on/off this
player is indicated as below:
“OPERATE”: CFD-S28L/S38L
“POWER”: CFD-S38
3
GB
Introduction
Basic Operations
GB
Table of contents
Basic Operations
4 Playing a CD
6 Listening to the radio
8 Playing a tape
10 Recording on a tape
The CD Player
12 Using the display
13 Locating a specific point in a
track
14 Playing tracks repeatedly
(Repeat Play)
15 Playing tracks in random order
(Shuffle Play)
16 Creating your own program
(Program Play)
18 Enjoying sound effects
(LOOP/FLASH)
The Radio
19 Presetting radio stations
20 Playing preset radio stations
The Timer
21 Setting the clock
22 Waking up to music
24 Falling asleep to music
Setting Up
25 Choosing the power sources
27 Selecting the audio emphasis
(SOUND/MEGA BASS)
Additional Information
28 Precautions
30 Troubleshooting
32 Maintenance
33 Specifications
34 Index
Basic Operations4
GB
Playing a CD
Basic Operations
Display
Playing timeTrack number
With the label side up
3 1, 2
Connect the supplied AC power cord (see page 25).
1 Press 6PUSH OPEN/CLOSE
down to open the CD
compartment and place the CD
on the CD compartment.
2 Close the lid of the CD
compartment.
3 Press ^.
The player turns on (direct
power-on) and plays all the tracks
once.
PUSH
OPEN/CLOSE
PUSH
OPEN/CLOSE
CD
Basic Operations
Basic Operations
5
GB
Use these buttons for additional operations
To Press
adjust the volume VOLUME +, – (VOL +, –
on the remote, CFD-S38/
S38L only)
stop playback p
pause playback ^ (P on the remote,
CFD-S38/S38L only)
Press the button again to
resume play after pause.
go to the next track +
go back to the previous track =
remove the CD 6 PUSH OPEN/CLOSE
turn on/off the player OPERATE (or POWER, see
page 2)
Tip
Next time you want to
listen to a CD, just press
^. The player turns on
automatically and starts
playing the CD.
OPERATE
(or POWER)
p
^
=, +
VOLUME +, –
6 PUSH OPEN/CLOSE
Basic Operations6
GB
Listening to the radio
Connect the supplied AC power cord (see page 25).
1 Press RADIO BAND until the
band you want appears in the
display (direct power-on).
2 Hold down TIME SET•TUNE
+ or – (TUNE + or – on the
remote, CFD-S38/S38L only)
until the frequency digits begin to
change in the display.
The player automatically scans
the radio frequencies and stops
when it finds a clear station.
If you can't tune in a station,
press the button repeatedly to
change the frequency step by
step.
Display
Indicates an FM stereo
broadcast
12
RADIO
BAND
PRESET
TIME
SET
TUNE
Basic Operations
Basic Operations
7
GB
Use these buttons for additional operations
To Press
adjust the volume VOLUME +, – (VOL +, –
on the remote, CFD-S38/
S38L only)
turn on/off the radio OPERATE (or POWER,
see page 2)
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself
for AM or MW/LW.
for FM for AM/MW/LW
Tips
If the FM broadcast is
noisy, press PLAY
MODE •MONO/ST ISS
until “Mono” appears in
the display and the
radio will play in
monaural.
Next time you want to
listen to the radio, just
press RADIO BAND.
The player turns on
automatically and starts
playing the previous
station.
OPERATE
(or POWER)
VOLUME +, –
PLAY MODE
MONO/ST ISS
Basic Operations8
GB
Playing a tape
Connect the supplied AC power cord (see page 25).
1 Press p6 to open the tape
compartment and insert a
recorded tape. Use TYPE I
(normal) tape only. Close the
compartment.
2 Press (.
The player turns on (direct
power-on) and starts playing.
With the side you want
to play facing upward
Display
12
STOP/EJECT
PLAY
Basic Operations
Basic Operations
9
GB
Use these buttons for additional operations
To Press
adjust the volume VOLUME +, – (VOL +, –
on the remote, CFD-S38/
S38L only)
stop playback p6
fast-forward or rewind the tape ) or 0
pause playback P
Press the button again to
resume play after pause.
eject the cassette p6
turn on/off the player OPERATE (or POWER,
see page 2)
Tip
Next time you want to
listen to a tape, just
press (. The player
turns on automatically
and starts playing the
tape.
p6
P
0
OPERATE
(or POWER)
VOLUME +, –
)
Basic Operations10
GB
Recording on a tape
Connect the supplied AC power cord (see page 25).
1 Press p6 to open the tape
compartment and insert a blank
tape. Use TYPE I (normal) tape
only.
2 Select the program source you
want to record.
To record from the CD player,
insert a CD (see page 4) and press
p on the CD section.
To record from the radio, tune in
the station you want (see page 6).
31
With the side you want to
record on facing upward
Display
STOP/EJECT
CD
RADIO
BAND
PRESET
Basic Operations
Basic Operations
11
GB
3 Press r to start recording
(( is depressed automatically).
Use these buttons for additional operations
Tips
Adjusting the volume or
the audio emphasis (see
page 27) will not affect
the recording level.
CFD-S28L/S38L only: If
the MW/LW program
makes a whistling
sound after you've
pressed r in step 3,
press PLAY MODE•
MONO/ST ISS
(Interference Suppress
switch) repeatedly until
the noise is at a
minimum.
For the best results, use
the AC power as a
power source.
To erase a recording,
proceed as follows:
1 Insert the tape whose
recording you want to
erase.
2 Press FUNCTION to
select “TAPE”.
3 Press r.
To Press
stop recording p6
pause recording P
Press the button again to
resume recording.
turn on/off the player OPERATE (or POWER, see
page 2)
p6
P
OPERATE
(or POWER)
FUNCTION
REC
PLAY MODE
MONO/ST ISS
The CD Player12
GB
Using the display
You can check information about the
CD using the display.
The CD Player
Checking the total track number and playing
time
Press DISPLAY ENT•MEMORY in stop mode.
If the CD has more than 12 tracks, “OVER 12” appears
in the display.
Checking the remaining time
Press DISPLAY•ENT MEMORY while playing a CD.
The track numbers in the music calendar disappear
after they are played.
To display
Press DISPLAY ENT•
MEMORY
the current track number once
and the remaining time
on the current track*
the number of tracks left twice
and remaining time on the CD
the current track number three times
and playing time
* For a track whose number is more than 20, the remaining
time appears as “- -:- -”.
Music calendar
Total playing time
Total track number
DISPLAY ENT
MEMORY
The CD Player
The CD Player 13
GB
Locating a specific
point in a track
You can quickly find a specific point in
a track while playing a CD.
You can also locate any track using the
number buttons on the remote
(CFD-S38/S38L only).
To locate Press
a point while listening to + (forward) or =
the sound (backward) while playing
and hold down until you
find the point
a point while observing + (forward) or =
the display (backward) in pause and
hold down until you find
the point
a specific track directly the number button of the
(CFD-S38/S38L only) track on the remote
Note
CFD-S38/S38L only:
You cannot locate a
specific track if
“SHUF” or “PGM” is lit
in the display. Turn off
the indication by
pressing p.
Tip
CFD-S38/S38L only:
When you locate a
track numbered over
10, press >10 first, then
the corresponding
number buttons.
Example:
To play track number
23, press >10 first, then
2 and 3.
=, +
The CD Player14
GB
Playing tracks
repeatedly
(Repeat Play)
You can play tracks repeatedly in
normal, shuffle or program play modes
(see page 16).
1 Press p.
“Cd” appears in the display.
2 Proceed as follows.
To repeat Do this
a single track 1 Press PLAY MODE•
MONO/ST ISS until “REP
1” appears.
2 Press = or + to select
the track that you want to
repeat.
3 Press ^.
all the tracks 1 Press PLAY MODE•
MONO/ST ISS until “REP
ALL” appears.
2 Press ^.
tracks in random order 1 Press PLAY MODE•
MONO/ST ISS until
“SHUF REP” appears.
2 Press ^.
programmed tracks 1 Press PLAY MODE•
MONO/ST ISS until
“PGM REP” appears.
2 Program tracks (see step 3
on page 16).
3 Press ^.
To cancel Repeat Play
Press PLAY MODE•MONO/ST ISS until “REP”
disappears from the display.
p
PLAY MODE
MONO/ST ISS
=, +
^
On the remote
(CFD-S38/S38L only)
1 Press p.
2 Press MODE until
the repeat mode you
want appears in the
display.
3 Do either of the
following to start
repeat play:
When you’ve
selected “REP 1”,
select the track by
pressing the
number button.
When you’ve
selected “REP
ALL” or “SHUF
REP”, press (.
When you’ve
selected “PGM
REP”, program
tracks (see step 3
on page 16), then
press (.
The CD Player
The CD Player 15
GB
Playing tracks in
random order
(Shuffle Play)
You can play tracks in random order.
1 Press p.
“Cd” appears in the display.
2 Press PLAY MODE•MONO/ST ISS until “SHUF”
appears in the display.
3 Press ^ to start shuffle play.
To cancel Shuffle Play
Press PLAY MODE•MONO/ST ISS until “SHUF”
disappears from the display.
On the remote
(CFD-S38/S38L only)
1 Press p.
2 Press MODE until
“SHUF” appears in
the display.
3 Press (.
p
^
PLAY MODE
MONO/ST ISS
The CD Player16
GB
Creating your
own program
(Program Play)
You can arrange the playing order of
up to 20 tracks on a CD.
Programed track
Playing order
1 Press p.
“Cd” appears in the display.
2 Press PLAY MODE•MONO/ST ISS until “PGM”
appears in the display.
3 Press the = or + then press DISPLAY ENT•
MEMORY for the tracks you want to program in
the order you want.
The programed tracks appear in the music
calender.
4 Press ^ to start program play.
On the remote
(CFD-S38/S38L only)
1 Press p.
2 Press MODE until
“PGM” appears in
the display.
3 Press the number
buttons for the tracks
you want to program
in the order you
want.
4 Press (.
p
PLAY MODE
MONO/ST ISS
=, +
^
DISPLAY ENT
MEMORY
The CD Player
The CD Player 17
GB
Tips
You can play the same
program again, since
the program is saved
until you open the CD
compartment.
You can record your
own program. After
you’ve created the
program, insert a blank
tape and press r to
start recording.
To cancel Program Play
Press PLAY MODE•MONO/ST ISS until “PGM”
disappears from the display.
To check the order of tracks before play
Press DISPLAY ENT• MEMORY.
Every time you press the button, the track number
appears in the programed order.
To change the current program
Press p once if the CD is stopped and twice if the CD
is playing. The current program will be erased. Then
create a new program following the programing
procedure.
The CD Player18
GB
Enjoying sound
effects
(LOOP/FLASH)
You can repeat part of a CD (LOOP)
and can “flash” the CD sound (FLASH)
during playback.
1 Play a CD.
2 Press and hold LOOP•AUTO PRESET or FLASH
at the point you want to start the function.
To Press and hold
repeat a selected part of a CD LOOP•
AUTO PRESET
“flash” the CD sound FLASH
To cancel the LOOP or FLASH function
Release the button.
The player returns to normal play.
LOOP
AUTO PRESET
FLASH
The Radio
The Radio
19
GB
The Radio
Presetting radio
stations
You can store radio stations into the
player’s memory. You can preset up to
30 radio stations (CFD-S28L/S38L) or 20
radio stations (CFD-S38), 10 for each
band in any order.
On the remote
(CFD-S38/S38L only)
1 Press BAND until the
band you want
appears in the
display.
2 Tune in a station you
want.
3 Hold down the
number buttons that
you want to preset
the new station on for
2 seconds.
RADIO BAND
DISPLAY ENT
MEMORY
PRESET +, –
1 Press RADIO BAND until the band you want
appears in the display.
2 Hold down LOOP•AUTO PRESET for 2 seconds
until “AUTO” appears in the display.
The stations are stored in memory from the lower
frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal
manually.
1 Press RADIO BAND to select the band.
2 Tune in a station you want.
3 Hold down DISPLAY ENT•MEMORY for 2
seconds.
4 Press PRESET + or – until the preset number (1 to
10) you want for the station flashes in the music
calender.
5 Press DISPLAY ENT•MEMORY.
The new station replaces the old one.
LOOP
AUTO PRESET
The Radio20
GB
Playing preset
radio stations
Once you've preset the stations, use the
number buttons on the remote or
PRESET +/– on the player to tune in to
your favorite stations.
1 Press RADIO BAND to select the band.
2 Press PRESET + or – to tune in the stored station.
On the remote
(CFD-S38/S38L only)
1 Press BAND to select
the band.
2 Press the number
buttons to tune in the
stored station.
RADIO BAND
PRESET +, –
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Sony CFD-S28L Operating instructions

Category
CD players
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages