Equinox Systems Apollo CFD Installation guide

Equinox Systems
Brand
Equinox Systems
Model
Apollo CFD
Type
Installation guide
Equinox Payments
9045 E. Pima Center Pkwy, Suite 3, Scosdale, AZ 85258, USA | Tel: +1.877.497.3726 | Fax: +1.480.551.7811 | www.EquinoxPayments.com
© 2013-2014 Equinox Payments, all rights reserved. Equinox Payments and the Equinox Payments logo are registered trade-
marks of Equinox Payments. Informaon within this guide may not match the terminal device and its accessories exactly and
thus are subject to change. 940649-001E Rev. C 09/14
INSTALLATION GUIDE
APOLLO CFD
INSTALLATION GUIDE
APOLLO CFD
WARNING
•
Only use the provided Equinox Payments A/C Power Adapter.
Non-compliant power adapters may damage the device.
•
Do not use if visibly damaged.
•
Do not expose to temperatures below -10 °C or above 60 °C
storage (not powered).
•
Intended operating humidity range is 5% to 95% rh (non-condensing).
•
Do not disassemble.
•
Do not incinerate or crush.
•
This device is not designed or cerfied to be used in a
flammable atmosphere such as a petrol staon or chemical
depot where there is a risk of explosion.
•
Keep out of reach of children or pets.
•
Only use your finger on the display. Do NOT use a pen,
pencil or hard p stylus for it WILL damage the display and
void the warranty.
SAFETY INFORMATION
The Apollo family of devices must be used within the operang
condions, electrical supply requirements, environmental
condions and connecon requirements as specified below:
•
Power Supply: These devices must be connected to the
correct electrical supply. Connecon to an inappropriate
supply may damage or destroy this device(s), thereby
invalidang its warranty(s).
•
Only operate these devices within the temperature range of
0 °C - 45 °C.
•
Hazardous Environments: These devices must NOT be
installed in locaons where there is danger of explosion.
COMPLIANCE
Changes or modificaons not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
•
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
on against harmful interference when the equipment is
operated in a commercial environment. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instrucon manual,
may cause harmful interference to radio communicaons.
Operaon of this equipment in a residenal area is likely to
cause harmful interference in which case the user will be
required to correct the interference in which case the user will
be required to correct the interference at his own expense.
The user is cauoned that changes or modificaons not ex-
pressly approved by the party responsible for compliance
could void the user’s authority to operate this device.
•
UL/cUL Listed
•
FCC ID: NVA00008
•
FCC Part 68
This device complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the underside of this
device is a label that contains, among other informaon, a
product idenfier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone
company.
A plug and jack used to connect this device to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with
this device. It is designed to be connected to a compable
modular jack that is also compliant.
The REN is used to determine the number of devices that may
be connected to a telephone line. Excessive RENs on a tele-
phone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the
total RENS, contact the local telephone company. The REN for
this device is part of the product idenfier that has the format
US:AAAEQ##-TXXXX, where the digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). If this
device causes harm to the telephone network, the telephone
company will nofy you in advance that temporary disconnu-
ance of service may be required. But if advance noce isn’t
praccal, the telephone company will nofy the customer as
soon as possible. Also, you will be advised of your right to file
a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilies,
equipment, operaons or procedures that could affect the
operaon of this device. If this happens, the telephone compa-
ny will provide advance noce in order for you to make neces-
sary modificaons to maintain uninterrupted service.
If trouble is experienced with this device, please contact
Equinox Payments at 1.877.497.3726 for repair or warran-
ty informaon. If this device is causing harm to the tele-
phone network, the telephone company may request that
you disconnect this device unl the problem is resolved.
The user is not authorized to perform any service of this device.
Connecon to party-line service is subject to state tariffs.
Contact the state public ulity commission, public service
commission, or corporaon commission for informaon.
940649-001E
SHIPPING
CONTENTS*
Addional cables
available for purchase:
• RS232 cable
• Ethernet cable
• MFD to AIO/CFD cable
(810417-002E)
• CFD/MFD Mono cable
(810418-002E)
RJ11 Cable (Line)
(810005-010)
A/C Power Adapter
(870082-10XE)
Apollo CFD Terminal
(020372-00XE)
*Contents may not exactly match
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Cerfied Telecommunicaon Line Cord.
APOLLO CFD INSTALLATION GUIDE
STEP 1: Remove Back Cover
BACK VIEW with COVER ON
Back Cover
MounƟng
Holes
STEP 2: Connect Cables
940649-001E
Push tab in to remove back cover
A
+
+
+
MFD Mono Cable
(810417-001E)
3
+
APOLLO MFD APOLLO CFD
CFD/MFD Mono Cable
(810418-002E)
+
Line
Port
RS232
Port
Ethernet
Port
USB Host
Port
USB OTG
Port
+
Power Port
A/C POWER CABLE
INSTALLATION or REMOVAL
Insert power cable
as shown
Clip
+ + +
CAUTION: Do NOT wiggle power cable to remove.
Doing so may break connector pins.
STEP 3: Connect CFD to MFD using Mono Cable
Press clip and
pull cable
straight up to
remove
+
MFD Mono
Cable
(810417-001E)
+
Power
Port
2
Line
Port
Ethernet
Port
USB Host
Port
6 5
7
+
4
Power Port
CAUTION: Do NOT wiggle power cable to remove.
Doing so may break connector pins.
A/C Power
Adapter
(870082-10XE)
+
MFD
Power
Port
+
Line
Port
+
Ethernet
Port
CAUTION:
Do NOT wiggle
power cable
to remove.
Doing so
may break
connector
pins.
1
Plug other end into
electrical outlet
(Inserted cable ends (as shown above)
are part of the CFD/MFD Mono Cable)
8
INSERT CABLES IN
NUMERICAL ORDER
A/C Power Adapter
  • Page 1 1
  • Page 2 2

Equinox Systems Apollo CFD Installation guide

Equinox Systems
Brand
Equinox Systems
Model
Apollo CFD
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents