ALIBI ALI-NZ6032M Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-NZ6032M
Category
Security cameras
Type
Quick Installation Manual

This manual is also suitable for

1
www.observint.com
ALI-NZ60xx_CQ
170720
First install the install the ALI-NZ60 base station, install the add-on camera, and then congure the system.
Install your
Add-on camera
Install the
ALI-NZ60 Base Station
(pg. 1)
Congure the System
(pg. 5)
Install the ALI-NZ60 Base Station
pg. 1
ALI-NZ6012M Add-on Camera Installation
pg. 2
ALI-NZ6022M Add-on Camera Installation
pg. 3
ALI-NZ6032M Add-on Camera Installation
pg. 3
ALI-NZ6042HS Add-on Camera Installation
pg. 4
Configure the System
pg. 5
Specifications
pg. 5
Install the ALI-NZ60 Base Station
The ALI-NZ60 module can be anchored to a surface or set on a table or shelf. Ensure that it is positioned
where it can be reached by the cable attached to the camera head. The module should be installed in a
clean, low-dust location that is within the temperature and humidity specications of the device. See the
Specications section at the end of this document.
ALI-NZ60 Base Station includes the following:
• ALI-NZ60 Base Station module
• Base Station mounting bracket
• Rail bracket
• Mounting hardware
Base Station
Mounting
Bracket
Mounting
hardware
Ra
il bracket
ALI-NZ60 Base Station front panel: LAN / power / alarm connections
RESET button: To reset the device to the factory default settings, press and hold in the button while you
power on the base station for 10 seconds.
ALI-NZ60 Base Station back panel: camera / audio drop cable connectors , microSD card slot
To install the base station:
1. Anchor the module on a surface:
ALI-NZ60 Series Camera System
Quick Installation Guide
This guide provides installation instructions for the following products:
Product SKU Name Camera Type
ALI-NZ60 Base Station for ALI-NZ60 Series Mini IP Security
Cameras
--
ALI-NZ6012M Add-on 2.1 Megapixel 1080p WDR Pinhole Tube
Mini IP Security Camera
1080P WDR 3.7 mm Pinhole Tube Camera
ALI-NZ6022M Add-on 2.1 Megapixel 1080p WDR Right Angle
Pinhole Mini IP Security Camera
1080P WDR 3.7 mm Right Angle Pinhole Camera
ALI-NZ6032M Add-on 2.1 Megapixel 1080p WDR Wide Angle
Tube Mini IP Security Camera
1080P WDR 2.8 mm Wide Angle Tube Camera
ALI-NZ6042HS Add-on IP Height Strip Camera 1080P WDR 3.7 mm Right Angle Pinhole Camera
The ALI-NZ60 series camera system features:
• 1/2.7” Progressive Scan CMOS
• Up to 1920 x 1080 @ 30 fps for real-time output
• IR cut lter with auto switch
• Rotate mode, BLC, Defog and 120 dB WDR are supported
• 12 Vdc power supply or PoE supported
• Built-in micro SD / SDHC / SDXC card slot, up to 128GB capacity (card not included)
• Support for HLC, Defog
Status LEDs
ALI-NZ60 Base Station
Back panel
Right Angle
Pinhole Camera Assembly
ALI-NZ60 Base Station module with Right Angle Pinhole Camera
Pinhole Tube Camera head (left, cable not shown) and Wide Angle Tube Camera (right)
For more information, refer to these documents available from your product vendor:
• ALIBI™ Tools Utility Installation and User Manual
• ALIBI™ IP Camera Firmware Version 5.3 (or later) User Manual
To install the ALI-NZ60 camera system:
Brackets and hardware is provided to mount the camera assembly at on a surface, on a surface using the
tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The
ALI-NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not
provided).
• Make sure the device in the package is in good condition and all the assembly parts are included.
• Check the products specication for the installation environment.
• If the product does not function properly, please contact your provider. Do not disassemble the
camera for repair or maintenance by yourself.
• Make sure that the mounting surface is strong enough to support at least three times the weight of
the camera or base station.
2
www.observint.com
a. Attach the ALI-NZ60 module mounting bracket to the back of the module using the four
screws provided. The release tab should be down. See the drawing below.
Tab: pull to release
ALI-NP60 module
Mounting
bracket
b. Attach the rail bracket to the surface where you want to mount the ALIL-NZ60 module. The
mounting hardware provided is adequate for most surfaces. If mounting the bracket onto a
vertical surface, mount the rail bracket horizontally.
ALI-NP60 module with
mounting bracket
Rail bracket
c. Slide the ALI-NZ60 module mounting bracket sideways onto the rail bracket.
2. Plug the camera head cable into the VIN1 jack on the NZ60 module (RJ12 connector).
3. Insert a microSD card into the SD card slot near the VIN1 jack. Push the card in until it locks into
place. The microSD card can range in size up to 128GB.
NOTE: If a microSD card is not used, the device will not retain log information or recordings in
the NZ60 module. However, log information and recordings may be saved in a network recorder
congured to manage the camera.
4. Connect devices to the termination block as needed. The RS232 terminations are not used.
a. Connect an alarm input sensor (not provided) to the IN1 and GND connectors on the
termination block. Strip about 1/8” insulation from the wires, then carefully push the bare
wire into the connector while holding in the button above the connector. The alarm sensor
can be congured for normally open (N.O.) or normally closed (N.C.) contacts.
Battery
+
-
1 Amp max
G
BP
Alarm In
Alarm Out
b. Connect an alarm output device (not provided) to the 1A and 1B connectors on the
termination block. Note that the 1A termination is on the same side of the battery as the
Battery + terminal. The internal alarm output circuit can drive up to 1 amp.
5. Plug a microphone and speaker (not provided) into the AUDIO IN and AUDIO OUT connectors on
the back of the controller.
6. Plug a network cable into the RJ45 LAN PoE connector on the front of the controller, and then plug
the other end of the cable into a router.
7. If the device is NOT powered through the network cable (PoE), plug a 12 Vdc power source into the
DC12V connector on the front of the NZ60 module. Use a power source that is adequate for the
device. Check the Specications section of this document for current/power requirements.
8. Check the STATUS LEDs on the face of the controller. Verify that:
POWER LED is solid red (normal when power is applied).
STATUS LED is solid green (the device is working normally). If this LED is ashing, the SD card may
not be recognized.
NETWORK LED is ashing amber (network is connected to the device).
ALI-NZ6012M Add-on Camera Installation
The ALI-NZ6012M add-on camera includes the following:
• 1080P WDR 3.7 mm Pinhole Tube Camera
• Round rail mounting bracket
Round rail
mounting
bracket
The AL-NZ6012M camera is used for concealed mounting only. To mounting the camera behind a surface:
1. Determine the best location for the camera. When mounted on a surface, the camera points out
perpendicular to the surface.
2. Drill a hole in the mounting surface for the camera lens. The hole should be large enough to not
obstruct the full view of the camera. Suggested hole sizes are shown below for dierent wall
thicknesses.
Camera (View angle)
Lens set back distance
from wall surface (in)
Hole size
(min. diameter in)
Drill (in)
ALI-NZ6012M (65˚)
0.25 .319 3/8 0.375
0.5 .637 11/16 0.688
0.75 .956 1.00.1.00
3. Remove the covering of the adhesive tape on the bracket, and then press the bracket onto the back
of the mounting surface, aligning the hole with the camera lens. See shown in gure below.
Front of
mounting
surface
Round rail
mounting
bracket
4. Install the camera into the round rail mounting bracket. See below.
ALI-NZ6012M
Camera censor
TOP label
5. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.
© 2016, 2017 Observint Technologies. All rights reserved.
3
www.observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
ALI-NZ6022M Add-on Camera Installation
ALI-NZ6022M add-on camera includes the following:
• 1080P WDR 3.7 mm Right Angle Pinhole camera
• Decorative cover
• Straight mounting bracket
• Tilt mounting bracket
• Foam pads (2)
Foam pads (2)
Tilt mount
bracket
D
ecorative cover
Straight mounting bracket
A bracket and hardware is provided to mount the camera assembly at on a surface, on a surface using the
tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The ALI-
NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not provided).
Mounting the camera on a surface
To mount the camera on a surface:
1. Determine the best location for the camera. Note that when mounted on a surface, the camera
points out perpendicular to the surface and has a view angle of 57˚.
2. Attach the camera to the surface with two screws. Depending on the surface, wall inserts may be
required. The mounting hardware provided is adequate for most surfaces.
Cover
Camera
3. Push the cover onto the camera. The cover will snap into place.
4. Route the cable to the location where the ALI-NZ60 Base Station module will be located.
Mounting the camera on a surface with the tilt-mount bracket
The tilt mount bracket is used to mount the camera on a vertical (wall) or horizontal (ceiling) surface where
tilting the camera provides a better eld of view. To use the tilt-mount bracket to mount the camera:
1. Determine the best location for the camera. The camera view angle is 65˚.
2. Attach the tilt-mount bracket to the surface.
the hardware provided is adequate for most
installations.
3. Attach the camera to the bracket with the two
screws provided.
4. Route the camera cable to the ALI-NZ60
module and plug it into the VIN1 connector.
5. After adjusting the camera for the best eld
of view, tighten the screws on the sides of the
tilt-mount bracket, and then attach the cover.
Tilt-mount bracket
Camera
Screw (2)
Mounting the camera behind a surface
To mount the camera behind a surface:
1. Determine the best location for the camera. Note that when mounted on a surface, the camera
points out perpendicular to the surface.
2. Drill a hole in the mounting surface for the camera lens. The hole should be large enough to not
obstruct the full view of the camera. Suggested hole sizes are shown below for dierent wall
thicknesses.
Camera (View angle)
Lens set back distance
from wall surface (in)
Hole size
(min. diameter in)
Drill (in)
ALI-NZ6022M (65˚)
0.5 .637 11/16 0.688
0.75 .956 1.00.1.00
3. Peal the protective paper o of one side of an adhesive foam strip and then align and apply it to the
face of the bracket. See the drawing below.
Adhesive foam
on surface
Camera
Hole
Bracket
Screw
4. Press the camera into the back of the bracket, and then tighten the screw to secure it in place.
5. Peal the protective paper from the front side of the adhesive foam on the bracket, and press the
bracket with the camera onto the surface, aligning the camera lens with the center of the hole.
6. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.
ALI-NZ6032M Add-on Camera Installation
ALI-NZ6032M add-on camera includes the following:
• 1080P WDR 2.8 mm Wide Angle Tube Camera
• Tilt mount bracket with sleeve assembly
Tilt-mount
bracket assembly
Sleeve
This product also includes a junction box adapter plate for attaching the camera assembly onto a
junction box.
The ALI-NZ6032M camera sensor is usually mounted to a ceiling with the tilt-mount bracket and sleeve
assembly provided. To install the camera:
1. Unscrew the tilt-mount bracket extension from the mounting base, and then lift o the mounting
base cover.
4
www.observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
Mounting base
Mounting base cover
Tilt-mount
bracket
extension
2. Attach the mounting base securely to the ceiling using two screws as needed. Screws and other
hardware items provided are adequate for mounting surfaces, but more appropriate fasteners may
be required.
Mounting base
3. Position the mounting base cover over the base, and then reattach the tilt-mount bracket extension.
4. Attach the sleeve to the camera sensor as shown in the drawing below. Install the screw (provided)
to secure the camera to the sleeve. The TOP label on the camera must be up.
Sleeve
Screw (provided)
ALI-NZ6032M camera sensor
TOP (label)
5. Screw the sleeve with the camera onto the tilt-mount bracket as shown below.
Lock
nut
Knob
6. Loosen the knob, and then aim the camera at your surveillance target. Tighten the knob and lock nut
to hold the camera in position.
7. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.
ALI-NZ6042HS Add-on Camera Installation
ALI-NZ6042HS add-on camera includes the following:
• 1080P WDR 3.7 mm Right Angle Pinhole camera
• Upper and lower end caps for height strip
• Camera mounting bracket
• Mounting screws
Upper, lower
end caps
Height Strip
Right Angle
Pinhole camera
Camera bracket
front and back
To install this camera:
1. Install the camera in the back of the camera bracket as shown below. The camera will snap into
place. Route the camera drop cable through the cable channel.
Cable
channel
2. Slide the plastic measuring guide out of the Height Strip.
Measuring guide
3. Anchor the Height Strip frame vertically at the preferred location. The mark inside the frame should
be 6 feet (1.83 m) above the oor. Use two screws, one at the top and one at the bottom. Screws
and other hardware items provided are adequate for mounting surfaces, but more appropriate
fasteners may be required.
Holes for
routing the
camera
drop cable
through the
surface
Height
strip
frame
5
www.observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
4. The camera drop cable can be routed either through the surface using the large holes in the frame,
or out through the end caps to be installed at the top or bottom of the frame. If routing the drop
cable through the surface, drill a hole through the surface at the upper or lower hole location in the
frame.
5. Position the camera bracket with the camera onto the raised screw holes in the frame, and then
secure it loosely with the screw or thumbscrew provided. Orient the bracket up or down as needed.
Place the camera bracket on the raised
screw holes in the frame. The bracket
can be oriented either up or down.
Use the screw or
thumbscrew provided to
hold the bracket in place.
6. Route the camera drop cable to the ALI-NZ60 base station, and then plug it into the VIN1 connector.
7. Adjust the pan angle of the camera as needed. It can point up to ± 15˚ from perpendicular to
the wall. NOTE: This adjustment may need to be re-performed after viewing live video from the
camera.
Adjust the pan direction
± 15 degrees from perpendicular
8. Install the other bracket screw or thumbscrew and then tighten both until snug to hold the camera
bracket in position.
9. Install the upper end cap with two screws (provided). If the camera drop cable is routed out the top,
remove the knockout for the cable.
Knockout for drop cable Screws
End cap
10. Reinstall the plastic measuring guide.
11. Install the lower end cap with two screws (provided). If the camera drop cable is routed out the
bottom, remove the knockout for the cable.
Configure the System
To perform the following steps, refer to the following documents available from your product vendor:
• ALIBI™ Tools Utility Installation and User Manual
• ALIBI™ IP Camera Firmware Version 5.3 (or later) User Manual
1. Refer to the ALIBI™ Tools Utility Installation and User Manual to do the following:
a. Install the Alibi Tools Utility on a computer connected to the same LAN as the device.
b. Use the Discover application to nd the device on the LAN.
c. Recongure the device network settings, if necessary. The default administrative username
is admin and password is undened. Create a Strong password for the device, and then
continue.
2. Use Microsoft Internet Explorer on a computer on the same network as the base station to log into
the device. Use the IP address of the device as the URL. The default administrative username is
admin and password is undened. Create a Strong password for the device, and then continue.
a. Create a new, strongly secure password for the device. A secure password improves the
overall security of the camera system.
b. Use the ALIBI™ IP Camera Firmware Version 5.3 User Manual to congure the device
as needed.
Specications
Camera
Image Sensor 1/2.7’’ Progressive Scan CMOS
Min. Illumination
0.01 Lux @ (F1.2, AGC ON) , 0 Lux with IR
0.028 Lux @ (F2.0, AGC ON), 0 Lux with IR
Shutter Speed 1/3 s ~ 1/100,000 s
Slow Shutter Supported
Lens Focal Length and
View Angle
For ALI-NZ6012M, ALI-NZ6022M, ALI-NZ6042HS: 3.7 mm @ F2.5, angle of view: 65°
For ALI-NZ6032M: 2.8 mm@ F2.0, angle of view: 115°
Lens Mount M12
Day and Night Electronic
WDR 120 dB
Digital Noise Reduction 3D DNR
Length of Lens Cable 6.6 ft (2 m)
Compression Standard
Video Compression
Main stream: H.264 / MJPEG
Sub stream: H.264 / MJPEG
Transcoded: H.264 / MJPEG
H.264 Type Main Prole / High Prole
H.264+ Supported
Video Bit Rate 32 Kbps – 16 Mbps
Audio Compression G.711 / G.722.1 / G.726 / MP2L2 / PCM
Audio Bit Rate 64 Kbps (G.711) / 16 Kbps (G.722.1) / 16 Kbps (G.726) / 32-160 Kbps (MP2L2)
Image
Max. Resolution 1920 × 1080
Main stream
50 Hz: 25 fps (1920×1080, 1280 × 960, 1280 × 720)
60 Hz: 30 fps (1920×1080, 1280 × 960, 1280 × 720)
Sub stream
50 Hz: 25 fps (704 × 576, 640 × 480, 352 × 288)
60 Hz: 30 fps (704 × 480, 640 × 480, 352 × 240)
Third stream
50 Hz: 25 fps (1920×1080, 1280 × 960, 1280 × 720, 704 × 576, 640 × 480, 352 × 288)
60 Hz: 30 fps (1920×1080, 1280 × 960, 1280 × 720, 704 × 480, 640 × 480, 352 × 240)
Image Enhancement BLC (Back Light Compensation) / 3D DNR / Defog
Image Setting Saturation, Brightness, Contrast, Sharpness adjustable by client software or web browser
Region of Interest (ROI) Supports 4 xed regions for each stream and dynamic face tracking
Day / Night switch Auto / Scheduled / Triggered by Alarm In
Picture Overlay LOGO picture can be overlaid on video with 128 × 128 24 bit image in .bmp format
Target Cropping Supported
6
www.observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
Audio
Environment noise
ltering
Supported
Audio I/O Supported
Audio sampling rate 48 kHz maximum
Smart feature set
Line Crossing Detection Cross a pre-dened virtual line, 1 pre-dened virtual lines supported
Intrusion Detection Enter and loiter in a pre-dened virtual region, 1 pre-dened virtual regions supported
Exception Detection Scene change detection, audio exception detection, defocus detection
Recognition Face detection recognition
Network
Network Storage Support Micro SD / SDHC / SDXC card up to 128GB for local storage and NAS (NFS, SMB/CIFS), ANR
Alarm Trigger
Motion detection, video tampering alarm, network disconnected, IP address conicted, illegal
login, HDD full, HDD error
Protocols
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP,
IGMP, 802.1X, QoS, IPv6, Bonjour
Standard ONVIF (PROFILE S, PROFILE G), PSIA, CGI, ISAPI
General
One-key reset, anti-icker, heartbeat, password protection, privacy mask, watermark, IP address
lter
Interface
Communication 1 × RJ45 10M/100M Ethernet interface
Audio Interface 1-ch 3.5 mm audio in (Mic in/Line in)/out interface
Alarm 1-ch alarm input, 1-ch alarm output (up to 24 Vdc 1A or 110 Vac 500 mA)
On-board storage Built-in Micro SD / SDHC / SDXC slot, up to 128 GB
Reset button Yes
General
Working temperature
and humidity
-22 °F ~ 140 °F (-30 °C ~ 60 °C)
Humidity 95% or less (non-condensing)
Power Supply 12 Vdc ± 10% / PoE (802.3af)
Power Consumption Max. 6.5 W
Dimensions
ALI-NZ60 Base station: 3.07" × 4.13" × 1.26" (78 × 105 × 32 mm)
Height strip bracket: 2.39" × 1.5" × 34.80" (60.6 × 38.2 × 883.8 mm)
Net Weight
Main body: 210 g
Cylindrical lens: 113 g
L-shaped lens: 99 g)
Tube lens: 129 g
Height strip bracket: 2.06 lb (934 g)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

ALIBI ALI-NZ6032M Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-NZ6032M
Category
Security cameras
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents