ALIBI ALI-NZ60 Quick Installation Manual

Brand: ALIBI

Model: ALI-NZ60

Category: Security cameras

Type: Quick Installation Manual

This manual is also suitable for

ALIBI ALI-NZ6012M is a 1080P WDR 3.7 mm Pinhole Tube Mini IP Security Camera that provides high-quality surveillance footage. With its compact size and discreet design, it's ideal for covert monitoring in various settings. The camera features:

1080p resolution: Captures clear and detailed images, ensuring you don't miss any crucial details.
Wide dynamic range (WDR): Adjusts exposure levels to provide a balanced image, even in challenging lighting conditions.
Pinhole design: Allows for discreet installation, making it less noticeable to potential intruders.
Tube construction: Provides a narrow field of view, making it suitable for monitoring specific areas.

1080p resolution: Captures clear and detailed images, ensuring you don't miss any crucial details.
Wide dynamic range (WDR): Adjusts exposure levels to provide a balanced image, even in challenging lighting conditions.
Pinhole design: Allows for discreet installation, making it less noticeable to potential intruders.
Tube construction: Provides a narrow field of view, making it suitable for monitoring specific areas.

www.observint.com

ALI-NZ60xx_CQ

170720

First install the install the ALI-NZ60 base station, install the add-on camera, and then congure the system.

Install your

Add-on camera

Install the

ALI-NZ60 Base Station

(pg. 1)

Congure the System

(pg. 5)

Install the ALI-NZ60 Base Station

pg. 1

ALI-NZ6012M Add-on Camera Installation

pg. 2

ALI-NZ6022M Add-on Camera Installation

pg. 3

ALI-NZ6032M Add-on Camera Installation

pg. 3

ALI-NZ6042HS Add-on Camera Installation

pg. 4

Configure the System

pg. 5

Specifications

pg. 5

Install the ALI-NZ60 Base Station

The ALI-NZ60 module can be anchored to a surface or set on a table or shelf. Ensure that it is positioned

where it can be reached by the cable attached to the camera head. The module should be installed in a

clean, low-dust location that is within the temperature and humidity specications of the device. See the

Specications section at the end of this document.

ALI-NZ60 Base Station includes the following:

• ALI-NZ60 Base Station module

• Base Station mounting bracket

• Rail bracket

• Mounting hardware

Base Station

Mounting

Bracket

Mounting

hardware

il bracket

ALI-NZ60 Base Station front panel: LAN / power / alarm connections

RESET button: To reset the device to the factory default settings, press and hold in the button while you

power on the base station for 10 seconds.

ALI-NZ60 Base Station back panel: camera / audio drop cable connectors , microSD card slot

To install the base station:

1. Anchor the module on a surface:

ALI-NZ60 Series Camera System

Quick Installation Guide

This guide provides installation instructions for the following products:

Product SKU Name Camera Type

ALI-NZ60 Base Station for ALI-NZ60 Series Mini IP Security

Cameras

ALI-NZ6012M Add-on 2.1 Megapixel 1080p WDR Pinhole Tube

Mini IP Security Camera

1080P WDR 3.7 mm Pinhole Tube Camera

ALI-NZ6022M Add-on 2.1 Megapixel 1080p WDR Right Angle

Pinhole Mini IP Security Camera

1080P WDR 3.7 mm Right Angle Pinhole Camera

ALI-NZ6032M Add-on 2.1 Megapixel 1080p WDR Wide Angle

Tube Mini IP Security Camera

1080P WDR 2.8 mm Wide Angle Tube Camera

ALI-NZ6042HS Add-on IP Height Strip Camera 1080P WDR 3.7 mm Right Angle Pinhole Camera

The ALI-NZ60 series camera system features:

• 1/2.7” Progressive Scan CMOS

• Up to 1920 x 1080 @ 30 fps for real-time output

• IR cut lter with auto switch

• Rotate mode, BLC, Defog and 120 dB WDR are supported

• 12 Vdc power supply or PoE supported

• Built-in micro SD / SDHC / SDXC card slot, up to 128GB capacity (card not included)

• Support for HLC, Defog

Status LEDs

ALI-NZ60 Base Station

Back panel

Right Angle

Pinhole Camera Assembly

ALI-NZ60 Base Station module with Right Angle Pinhole Camera

Pinhole Tube Camera head (left, cable not shown) and Wide Angle Tube Camera (right)

For more information, refer to these documents available from your product vendor:

• ALIBI™ Tools Utility Installation and User Manual

• ALIBI™ IP Camera Firmware Version 5.3 (or later) User Manual

To install the ALI-NZ60 camera system:

Brackets and hardware is provided to mount the camera assembly at on a surface, on a surface using the

tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The

ALI-NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not

provided).

• Make sure the device in the package is in good condition and all the assembly parts are included.

• Check the products specication for the installation environment.

• If the product does not function properly, please contact your provider. Do not disassemble the

camera for repair or maintenance by yourself.

• Make sure that the mounting surface is strong enough to support at least three times the weight of

the camera or base station.

www.observint.com

a. Attach the ALI-NZ60 module mounting bracket to the back of the module using the four

screws provided. The release tab should be down. See the drawing below.

Tab: pull to release

ALI-NP60 module

Mounting

bracket

b. Attach the rail bracket to the surface where you want to mount the ALIL-NZ60 module. The

mounting hardware provided is adequate for most surfaces. If mounting the bracket onto a

vertical surface, mount the rail bracket horizontally.

ALI-NP60 module with

mounting bracket

Rail bracket

c. Slide the ALI-NZ60 module mounting bracket sideways onto the rail bracket.

2. Plug the camera head cable into the VIN1 jack on the NZ60 module (RJ12 connector).

3. Insert a microSD card into the SD card slot near the VIN1 jack. Push the card in until it locks into

place. The microSD card can range in size up to 128GB.

NOTE: If a microSD card is not used, the device will not retain log information or recordings in

the NZ60 module. However, log information and recordings may be saved in a network recorder

congured to manage the camera.

4. Connect devices to the termination block as needed. The RS232 terminations are not used.

a. Connect an alarm input sensor (not provided) to the IN1 and GND connectors on the

termination block. Strip about 1/8” insulation from the wires, then carefully push the bare

wire into the connector while holding in the button above the connector. The alarm sensor

can be congured for normally open (N.O.) or normally closed (N.C.) contacts.

Battery

1 Amp max

Alarm In

Alarm Out

b. Connect an alarm output device (not provided) to the 1A and 1B connectors on the

termination block. Note that the 1A termination is on the same side of the battery as the

Battery + terminal. The internal alarm output circuit can drive up to 1 amp.

5. Plug a microphone and speaker (not provided) into the AUDIO IN and AUDIO OUT connectors on

the back of the controller.

6. Plug a network cable into the RJ45 LAN PoE connector on the front of the controller, and then plug

the other end of the cable into a router.

7. If the device is NOT powered through the network cable (PoE), plug a 12 Vdc power source into the

DC12V connector on the front of the NZ60 module. Use a power source that is adequate for the

device. Check the Specications section of this document for current/power requirements.

8. Check the STATUS LEDs on the face of the controller. Verify that:

POWER LED is solid red (normal when power is applied).

STATUS LED is solid green (the device is working normally). If this LED is ashing, the SD card may

not be recognized.

NETWORK LED is ashing amber (network is connected to the device).

ALI-NZ6012M Add-on Camera Installation

The ALI-NZ6012M add-on camera includes the following:

• 1080P WDR 3.7 mm Pinhole Tube Camera

• Round rail mounting bracket

Round rail

mounting

bracket

The AL-NZ6012M camera is used for concealed mounting only. To mounting the camera behind a surface:

1. Determine the best location for the camera. When mounted on a surface, the camera points out

perpendicular to the surface.

2. Drill a hole in the mounting surface for the camera lens. The hole should be large enough to not

obstruct the full view of the camera. Suggested hole sizes are shown below for dierent wall

thicknesses.

Camera (View angle)

Lens set back distance

from wall surface (in)

Hole size

(min. diameter in)

Drill (in)

ALI-NZ6012M (65˚)

0.25 .319 3/8 0.375

0.5 .637 11/16 0.688

0.75 .956 1.00.1.00

3. Remove the covering of the adhesive tape on the bracket, and then press the bracket onto the back

of the mounting surface, aligning the hole with the camera lens. See shown in gure below.

Front of

mounting

surface

Round rail

mounting

bracket

4. Install the camera into the round rail mounting bracket. See below.

ALI-NZ6012M

Camera censor

TOP label

5. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.

www.observint.com

ALI-NZ6022M Add-on Camera Installation

ALI-NZ6022M add-on camera includes the following:

• 1080P WDR 3.7 mm Right Angle Pinhole camera

• Decorative cover

• Straight mounting bracket

• Tilt mounting bracket

• Foam pads (2)

Foam pads (2)

Tilt mount

bracket

ecorative cover

Straight mounting bracket

A bracket and hardware is provided to mount the camera assembly at on a surface, on a surface using the

tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The ALI-

NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not provided).

Mounting the camera on a surface

To mount the camera on a surface:

1. Determine the best location for the camera. Note that when mounted on a surface, the camera

points out perpendicular to the surface and has a view angle of 57˚.

2. Attach the camera to the surface with two screws. Depending on the surface, wall inserts may be

required. The mounting hardware provided is adequate for most surfaces.

Cover

Camera

3. Push the cover onto the camera. The cover will snap into place.

4. Route the cable to the location where the ALI-NZ60 Base Station module will be located.

Mounting the camera on a surface with the tilt-mount bracket

The tilt mount bracket is used to mount the camera on a vertical (wall) or horizontal (ceiling) surface where

tilting the camera provides a better eld of view. To use the tilt-mount bracket to mount the camera:

1. Determine the best location for the camera. The camera view angle is 65˚.

2. Attach the tilt-mount bracket to the surface.

the hardware provided is adequate for most

installations.

3. Attach the camera to the bracket with the two

screws provided.

4. Route the camera cable to the ALI-NZ60

module and plug it into the VIN1 connector.

5. After adjusting the camera for the best eld

of view, tighten the screws on the sides of the

tilt-mount bracket, and then attach the cover.

Tilt-mount bracket

Camera

Screw (2)

Mounting the camera behind a surface

To mount the camera behind a surface:

1. Determine the best location for the camera. Note that when mounted on a surface, the camera

points out perpendicular to the surface.

2. Drill a hole in the mounting surface for the camera lens. The hole should be large enough to not

obstruct the full view of the camera. Suggested hole sizes are shown below for dierent wall

thicknesses.

Camera (View angle)

Lens set back distance

from wall surface (in)

Hole size

(min. diameter in)

Drill (in)

ALI-NZ6022M (65˚)

0.5 .637 11/16 0.688

0.75 .956 1.00.1.00

3. Peal the protective paper o of one side of an adhesive foam strip and then align and apply it to the

face of the bracket. See the drawing below.

Adhesive foam

on surface

Camera

Hole

Bracket

Screw

4. Press the camera into the back of the bracket, and then tighten the screw to secure it in place.

5. Peal the protective paper from the front side of the adhesive foam on the bracket, and press the

bracket with the camera onto the surface, aligning the camera lens with the center of the hole.

6. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.

ALI-NZ6032M Add-on Camera Installation

ALI-NZ6032M add-on camera includes the following:

• 1080P WDR 2.8 mm Wide Angle Tube Camera

• Tilt mount bracket with sleeve assembly

Tilt-mount

bracket assembly

Sleeve

This product also includes a junction box adapter plate for attaching the camera assembly onto a

junction box.

The ALI-NZ6032M camera sensor is usually mounted to a ceiling with the tilt-mount bracket and sleeve

assembly provided. To install the camera:

1. Unscrew the tilt-mount bracket extension from the mounting base, and then lift o the mounting

base cover.

www.observint.com

Mounting base

Mounting base cover

Tilt-mount

bracket

extension

2. Attach the mounting base securely to the ceiling using two screws as needed. Screws and other

hardware items provided are adequate for mounting surfaces, but more appropriate fasteners may

be required.

Mounting base

3. Position the mounting base cover over the base, and then reattach the tilt-mount bracket extension.

4. Attach the sleeve to the camera sensor as shown in the drawing below. Install the screw (provided)

to secure the camera to the sleeve. The TOP label on the camera must be up.

Sleeve

Screw (provided)

ALI-NZ6032M camera sensor

TOP (label)

5. Screw the sleeve with the camera onto the tilt-mount bracket as shown below.

Lock

nut

Knob

6. Loosen the knob, and then aim the camera at your surveillance target. Tighten the knob and lock nut

to hold the camera in position.

7. Plug the camera cable into the VIN1 connector of the ALI-NZ60 module.

ALI-NZ6042HS Add-on Camera Installation

ALI-NZ6042HS add-on camera includes the following:

• 1080P WDR 3.7 mm Right Angle Pinhole camera

• Upper and lower end caps for height strip

• Camera mounting bracket

• Mounting screws

Upper, lower

end caps

Height Strip

Right Angle

Pinhole camera

Camera bracket

front and back

To install this camera:

1. Install the camera in the back of the camera bracket as shown below. The camera will snap into

place. Route the camera drop cable through the cable channel.

Cable

channel

2. Slide the plastic measuring guide out of the Height Strip.

Measuring guide

3. Anchor the Height Strip frame vertically at the preferred location. The mark inside the frame should

be 6 feet (1.83 m) above the oor. Use two screws, one at the top and one at the bottom. Screws

and other hardware items provided are adequate for mounting surfaces, but more appropriate

fasteners may be required.

Holes for

routing the

camera

drop cable

through the

surface

Height

strip

frame

www.observint.com

4. The camera drop cable can be routed either through the surface using the large holes in the frame,

or out through the end caps to be installed at the top or bottom of the frame. If routing the drop

cable through the surface, drill a hole through the surface at the upper or lower hole location in the

frame.

5. Position the camera bracket with the camera onto the raised screw holes in the frame, and then

secure it loosely with the screw or thumbscrew provided. Orient the bracket up or down as needed.

Place the camera bracket on the raised

screw holes in the frame. The bracket

can be oriented either up or down.

Use the screw or

thumbscrew provided to

hold the bracket in place.

6. Route the camera drop cable to the ALI-NZ60 base station, and then plug it into the VIN1 connector.

7. Adjust the pan angle of the camera as needed. It can point up to ± 15˚ from perpendicular to

the wall. NOTE: This adjustment may need to be re-performed after viewing live video from the

camera.

Adjust the pan direction

± 15 degrees from perpendicular

8. Install the other bracket screw or thumbscrew and then tighten both until snug to hold the camera

bracket in position.

9. Install the upper end cap with two screws (provided). If the camera drop cable is routed out the top,

remove the knockout for the cable.

Knockout for drop cable Screws

End cap

10. Reinstall the plastic measuring guide.

11. Install the lower end cap with two screws (provided). If the camera drop cable is routed out the

bottom, remove the knockout for the cable.

Configure the System

To perform the following steps, refer to the following documents available from your product vendor:

• ALIBI™ Tools Utility Installation and User Manual

• ALIBI™ IP Camera Firmware Version 5.3 (or later) User Manual

1. Refer to the ALIBI™ Tools Utility Installation and User Manual to do the following:

a. Install the Alibi Tools Utility on a computer connected to the same LAN as the device.

b. Use the Discover application to nd the device on the LAN.

c. Recongure the device network settings, if necessary. The default administrative username

is admin and password is undened. Create a Strong password for the device, and then

continue.

2. Use Microsoft Internet Explorer on a computer on the same network as the base station to log into

the device. Use the IP address of the device as the URL. The default administrative username is

admin and password is undened. Create a Strong password for the device, and then continue.

a. Create a new, strongly secure password for the device. A secure password improves the

overall security of the camera system.

b. Use the ALIBI™ IP Camera Firmware Version 5.3 User Manual to congure the device

as needed.

Specications

Camera

Image Sensor 1/2.7’’ Progressive Scan CMOS

Min. Illumination

0.01 Lux @ (F1.2, AGC ON) , 0 Lux with IR

0.028 Lux @ (F2.0, AGC ON), 0 Lux with IR

Shutter Speed 1/3 s ~ 1/100,000 s

Slow Shutter Supported

Lens Focal Length and

View Angle

For ALI-NZ6012M, ALI-NZ6022M, ALI-NZ6042HS: 3.7 mm @ F2.5, angle of view: 65°

For ALI-NZ6032M: 2.8 mm@ F2.0, angle of view: 115°

Lens Mount M12

Day and Night Electronic

WDR 120 dB

Digital Noise Reduction 3D DNR

Length of Lens Cable 6.6 ft (2 m)

Compression Standard

Video Compression

Main stream: H.264 / MJPEG

Sub stream: H.264 / MJPEG

Transcoded: H.264 / MJPEG

H.264 Type Main Prole / High Prole

H.264+ Supported

Video Bit Rate 32 Kbps – 16 Mbps

Audio Compression G.711 / G.722.1 / G.726 / MP2L2 / PCM

Audio Bit Rate 64 Kbps (G.711) / 16 Kbps (G.722.1) / 16 Kbps (G.726) / 32-160 Kbps (MP2L2)

Image

Max. Resolution 1920 × 1080

Main stream

50 Hz: 25 fps (1920×1080, 1280 × 960, 1280 × 720)

60 Hz: 30 fps (1920×1080, 1280 × 960, 1280 × 720)

Sub stream

50 Hz: 25 fps (704 × 576, 640 × 480, 352 × 288)

60 Hz: 30 fps (704 × 480, 640 × 480, 352 × 240)

Third stream

50 Hz: 25 fps (1920×1080, 1280 × 960, 1280 × 720, 704 × 576, 640 × 480, 352 × 288)

60 Hz: 30 fps (1920×1080, 1280 × 960, 1280 × 720, 704 × 480, 640 × 480, 352 × 240)

Image Enhancement BLC (Back Light Compensation) / 3D DNR / Defog

Image Setting Saturation, Brightness, Contrast, Sharpness adjustable by client software or web browser

Region of Interest (ROI) Supports 4 xed regions for each stream and dynamic face tracking

Day / Night switch Auto / Scheduled / Triggered by Alarm In

Picture Overlay LOGO picture can be overlaid on video with 128 × 128 24 bit image in .bmp format

Target Cropping Supported

www.observint.com

Audio

Environment noise

ltering

Supported

Audio I/O Supported

Audio sampling rate 48 kHz maximum

Smart feature set

Line Crossing Detection Cross a pre-dened virtual line, 1 pre-dened virtual lines supported

Intrusion Detection Enter and loiter in a pre-dened virtual region, 1 pre-dened virtual regions supported

Exception Detection Scene change detection, audio exception detection, defocus detection

Recognition Face detection recognition

Network

Network Storage Support Micro SD / SDHC / SDXC card up to 128GB for local storage and NAS (NFS, SMB/CIFS), ANR

Alarm Trigger

Motion detection, video tampering alarm, network disconnected, IP address conicted, illegal

Protocols

TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP,

IGMP, 802.1X, QoS, IPv6, Bonjour

Standard ONVIF (PROFILE S, PROFILE G), PSIA, CGI, ISAPI

General

One-key reset, anti-icker, heartbeat, password protection, privacy mask, watermark, IP address

lter

Interface

Communication 1 × RJ45 10M/100M Ethernet interface

Audio Interface 1-ch 3.5 mm audio in (Mic in/Line in)/out interface

Alarm 1-ch alarm input, 1-ch alarm output (up to 24 Vdc 1A or 110 Vac 500 mA)

On-board storage Built-in Micro SD / SDHC / SDXC slot, up to 128 GB

Reset button Yes

General

Working temperature

and humidity

-22 °F ~ 140 °F (-30 °C ~ 60 °C)

Humidity 95% or less (non-condensing)

Power Supply 12 Vdc ± 10% / PoE (802.3af)

Power Consumption Max. 6.5 W

Dimensions

ALI-NZ60 Base station: 3.07" × 4.13" × 1.26" (78 × 105 × 32 mm)

Height strip bracket: 2.39" × 1.5" × 34.80" (60.6 × 38.2 × 883.8 mm)

Net Weight

Main body: 210 g

Cylindrical lens: 113 g

L-shaped lens: 99 g)

Tube lens: 129 g

Height strip bracket: 2.06 lb (934 g)

ALIBI ALI-NZ60 Quick Installation Manual

Brand: ALIBI

Model: ALI-NZ60

Category: Security cameras

Type: Quick Installation Manual

This manual is also suitable for

1080p resolution: Captures clear and detailed images, ensuring you don't miss any crucial details.
Wide dynamic range (WDR): Adjusts exposure levels to provide a balanced image, even in challenging lighting conditions.
Pinhole design: Allows for discreet installation, making it less noticeable to potential intruders.
Tube construction: Provides a narrow field of view, making it suitable for monitoring specific areas.

Download PDF

report

ALIBI ALI-NZ60 Quick Installation Manual

This manual is also suitable for

ALIBI ALI-NZ60 Quick Installation Manual

Related papers

Other documents