Magnescale LG20 is a versatile device designed to meet various measurement needs. Its key capabilities include:
-
Display Resolution and Polarity:
- Adjust the measurement unit resolution for precise readings.
- Reverse the counting direction (display polarity) as per your requirement.
-
Diameter Display:
- Display measurements as diameters, doubling the count value for convenience.
-
Detailed Settings:
- Access advanced settings to fine-tune the display resolution of each axis.
- Set the diameter display option for specific axes.
Magnescale LG20 is a versatile device designed to meet various measurement needs. Its key capabilities include:
-
Display Resolution and Polarity:
- Adjust the measurement unit resolution for precise readings.
- Reverse the counting direction (display polarity) as per your requirement.
-
Diameter Display:
- Display measurements as diameters, doubling the count value for convenience.
-
Detailed Settings:
- Access advanced settings to fine-tune the display resolution of each axis.
- Set the diameter display option for specific axes.
1/2
LG20 Change of display resolution (polarity)
Press key of the axis you want to change and select
the measurement unit resolution.
When you have made your selection, press key to save your settings.
Press key once while the display is .
The display will be (measurement unit resolution).
Press key to check the current measurement unit resolution.
LG20 Change of display resolution (polarity)
Ver.1 (2021.1) CS&S
* If you do not know the output resolution of the measurement unit, refer to the separate "Initial setup manual".
About 2 sec
For LG20-1, LG20-2, LG20-3
Press key once to automatically switch to advanced settings mode.
The display will be .
Press key, the display becomes the normal display.
Display of measurement unit resolution (LG20-3)
Purpose of change Operation Explanation
Change the measurement unit resolution Change the length measurement unit resolution in
the basic settings. And check the display resolution
in the detailed settings.
Change the display resolution Change the display resolution in the detailed
settings
Change the display polarity
(Counting direction is reversed)
Change the display resolution in the detailed
settings
Diameter display (double count value) Change to diameter display with display resolution
in the detailed settings
Detailed settings ⇒Display resolution ⇒Change
Detailed settings ⇒Display resolution ⇒Diameter display
LG20-3
The operation method for changing the display resolution differs depending on the purpose and conditions of the change.
Select the purpose and conditions to be changed from the table below and perform the operation.
Basic settings ⇒Measurement unit resolution ⇒Change
Detailed settings ⇒Display resolution ⇒Change polarity
Selection of measurement unit resolution
Set to basic setting mode.
Turn key “ON” while the AC adapter is energized.
Press and hold key for 3 seconds after the lamp changes from blinking to off.
Basic settings ⇒Measurement unit resolution ⇒Change
①
②
③
④
⑤
Switch from basic settings to normal count mode.
Press key once and the display will change to .
Press key once and the display will change to .
Input 1
Input 2
Input 3
Power ON
2/2
LG20 Change of display resolution (polarity)
Diameter display
Length display
NOTE : Selection of a value smaller than the basic settings measurement
unit resolution is not displayed.
Selection of display resolution
Press key once to display the display resolution of each axis.
Press key of the axis you want to change and select the resolution.
Please note that the lamp lights up once every two times and
the diameter display is set.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Set to the detailed settings mode.
Press key while the normal count mode is energized.
The display will be . (Detailed settings mode)
Detailed settings ⇒Display resolution ⇒Change
①
②
Before After
Change polarity
Example of changing the polarity of the display in the middle row
Set to advanced mode.
Press key in normal count mode
The display will be .
Press key once to get the display resolution of each axis.
Press key of the axis you want to change to the diameter display and turn on the lamp.
If the resolution changes, press key again.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Press key once to get the display resolution of each axis.
Press key for the axis for which you want to change the polarity,
and then press key.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Detailed settings ⇒Display resolution ⇒Diameter display
Detailed settings ⇒Display resolution ⇒Change polarity
①
②
②
Set to advanced mode.
Press key in normal count mode
The display will be .
①
Diameter display
-
1
-
2
Magnescale LG20 is a versatile device designed to meet various measurement needs. Its key capabilities include:
-
Display Resolution and Polarity:
- Adjust the measurement unit resolution for precise readings.
- Reverse the counting direction (display polarity) as per your requirement.
-
Diameter Display:
- Display measurements as diameters, doubling the count value for convenience.
-
Detailed Settings:
- Access advanced settings to fine-tune the display resolution of each axis.
- Set the diameter display option for specific axes.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
HP 8568B User manual
-
Energy Star 200W6CS User manual
-
ACU-RITE III User manual
-
YOKOGAWA DL6154 User manual
-
Agilent Technologies InfiniiVision 6000 Series User manual
-
-
Agilent Technologies 54622D User manual
-
LeCroy WavePro HD User manual
-
-
Meiji Techno MTIEH-542-072A Owner's manual
