Multoo MT1 User manual

Brand: Multoo

Model: MT1

Type: User manual

Manual of multoo 3D printing

Accessories

Standard Advance

Power Wire Y Y

USB cable Y Y

Wrench Y Y

Single Extruder Kit Y Y

Dual Extruder Kit Y Y

Laser Engraving Kit N Y

Protective Glasses N Y

Filament Bracket Y Y

2 Rolls Filament Y Y

Glue Stick Y Y

SD card Y Y

Assemble Structure

Suggestion: this step shell be completed by two persons.

Products assembly specific operation as follows:

multoo 3d printer assembly only two sections, pedestal and Z Aluminum frame.

As shown in the picture:

Pedestal:

Z Frame:

Next we start the assembly steps ...

Electrical box

Please fix electrical box behind Z aluminum frame, as long

as not drop.

Move Print-plate

Please put bottom parts on flat desktop, and push printing

plate to the forefront.

Fix Pedestal and Z frame Together

Please assemble Z frame and bottom frame of Pedestal

together. First, please put Z frame onto bottom frame,

then put T-form screws into groove as bellow(don't

tigthen temporary ), the same operation on the other

side(can tighten) .

Finally, ensure both sides is fastening state.

Screen

Please fix screen on Y aluminium frame, and

screw them with screwdriver.

Adjust the box height

The wire of extruder module throught electrical box, and

adjust the distance is 290mm as below.

Note: please do not pull wires fiercely, or else it will lead

to loose contact.

Power cable

There are two relatively thick wires. One has

two wires and the other has three wires.

Please see the figure.

We give them a number, A has two lines, B has

three lines.

So,

A-brown => Abrown

A-blue => Ab

B-yellow => By

B-blue => Bb

B-brown => Bbrown

Connection

Please complete the connection according to the color.

Left ---- > Right

1 2 3 4 5 6 7 8 9

Abrown Ab By Bb Bbrown

Notice,

Color brown is positive or FireWire.

Color blue is negative or neutral.

Color yellow is the ground. Take easy.

Wiring section

Note: The limit switch has 3 root wires, the motor has 4 root wires.

The X motor wires and limit switch wires is in together, can be found easily according to

line mark. please connect wires to X motor and limit switch respectively.

The rest of limit switch wires for Y and Z. Connect the shorter wires to Z axis limit switch,

connect the longer wires to Y axis limit switch.

Then connect wires to Y motor and Z motor respectively.

Extruder modules assembly

Just put extruder or laser engraver onto pedestal of extruder, then use screwdriver

tightened. All operations are simple.

Level plate

Please level plate well when first printing.

Choose "Prepare" -> "Plate Leveling" in LCD.

Prepare a piece of A4 paper, then put it between nozzle and glass, when the nozzle

puse, you can adjust the height of plate by rotating 4 nuts beneath.

The nozzl will go though 4 level points in turn. When it

moves to first leveling point, please twitch paper, if there is

slight friction, it means OK, then move to next point.

Components

All printing parts in SD card Gcode folder. if you want to recepment them, can printing

them directly.

Hope you will enjoy 3D printing very much! : )

multoo

Yiwu Mantuo Intelligent Technology Co.,Ltd

Website : www.multoo.com

Email : [email protected]

Skype : karenshi521

Add.: Liuqing District No.23, Yiwu City, Zhejiang Province, China

Multoo MT1 User manual

Brand: Multoo

Model: MT1

Type: User manual

Download PDF

report

Multoo MT1 User manual

Multoo MT1 User manual

Other documents