Orava CM-551 User manual
- Category
- Small kitchen appliances
- Type
- User manual
Cotton candy device
CM-551
CM-551
Instruction manual EN
2EN
Intended use of the device
The equipment is intended solely for the manufacture of cotton candy, from
pure crystal sugar (or similar crystalline sugar), to the extent determined
by technical and operational parameters and functions, safety and user
instructions, and external infl uences of the operating environment.
ORAVA electrical appliances are manufactured according to state-of-the-art
knowledge and recognized safety regulations. Nevertheless, improper or
improper use or improper use may result in injury or endangerment to the life
of the user or a third party or to a third party. damage to equipment and other
property.
1. GENERAL SAFETY INSTRUCTIONS AND WARNINGS
• This document contains important safety instructions and warnings for safe,
correct and economical operation of the electrical equipment. Its compliance
helps the user avoid risks, increase reliability and product life.
• In this document, the generic term product is used in text parts such as:
electrical equipment - any device used for the production, conversion,
transmission, distribution or use of electricity.
• From the point of view of the purpose of using electricity, the concept of
electrical equipment in the strict sense of the word will include the following
categories:
- household electric appliances,
- information and communication equipment,
- consumer electronics,
- lighting equipment,
- electrical and electronic tools,
- toys and equipment for sporting and recreational
1.1 General safety instructions
• Before commissioning the unit, we recommend that you carefully read
the operating instructions and operate the equipment in accordance with the
instructions!
• The safety instructions and warnings in this manual do not cover all the
possible conditions and situations that may arise when using the device. The
user must understand that a factor that can not be incorporated into any of the
products is responsibility and caution. These factors must therefore be ensured
by users / users who use and operate this device.
• Failure to follow the safety instructions and warnings is forbidden by the
manufacturer for any damage to health or property!
• Make sure that the appliance is complete and shows no signs of damage
before using the appliance for the fi rst time. If the product is defective or if it
has any visible damage, do not use the product.
• Keep the operating instructions as close to the device as possible throughout
its service life. Always keep the operating instructions together with the
appliance for future use and use by new users.
• Use the appliance only for the purpose for which it is intended and in the
manner specifi ed by the manufacturer.
• The appliance is intended for home and similar indoor use, with no special
focus.
3EN
• It is not a professional device for commercial use.
• Do not change the technical parameters and features of the device by
unauthorized modifi cation or modifi cation of any part of the device.
• The manufacturer is not responsible for damages caused during
transportation, misuse, damage or destruction of the equipment due to
adverse weather conditions.
1.2 Safety of the operating environment
• Do not use the device in an industrial environment or outside environment.
• Always keep the operating environment clean and well lit.
• Do not place the device on an unstable surface. Overriding or dropping the
device may result in personal injury or damage to the device.
• Do not expose the unit to direct sunlight or excessive heat sources.
• Do not use an electric appliance in areas with fl ammable liquids, gases or dust.
The appliance may be the source of scaling, which can result in the ignition of
dust or vapors.
Features of the operating environment
1. Ambient temperature: +5 ÷ +40 ° C
2. Humidity: 5 ÷ 85%
3. Altitude: ≤ 2 000 m
4. Occurrence of water: intermittent condensation of water or occurrence of water
vapor
5. Occurrence of foreign bodies: amount and type of dust are not signifi cant
Protection class: IP20
• Other characteristics of the operating environment (mechanical stress
- shocks and vibrations, occurrence of plant, animals, weather effects) are
negligible in terms of effect on the correct and safe use of electrical equipment.
1.3 Electrical safety
• Before connecting the appliance to the power supply for the fi rst time, make
sure that the voltage on the appliance label corresponds to that of the
household electrical outlet.
• The electrical appliance is designed for mains supply 230 V ~.
The electrical safety of the appliance is guaranteed only if it is properly
connected to the electricity grid.
• Only use a power cord with a plug (mains lead) that came with the device and
compatible with a wall outlet. Using another cable may result in fi re or electric
shock.
• Always connect an electrical appliance to an easily accessible power outlet. In
the event of an operating fault, the appliance must be switched off as soon as
possible and disconnected from mains supply.
• Do not pull the power cord / power cord by pulling on the cord / cord.
Disconnect the power cord by pulling the plug behind the power cord / power
cord plug.
• If you use an extension cord, check that the total rated (ampere) power of
all devices connected to the extension cord does not exceed the maximum
current rating of the extension cable.
• If you need to use an extension cord or power supply block, make sure that
the extension cord or power pack is plugged into a power outlet, and not to
another extension cord or power supply. Extension power cord or power supply
block must be designed for grounded plugs and plugged into a grounded
outlet.
4EN
• The power plug of the appliance must be compatible with the mains socket.
Never use any adapters or modify the socket in any other way. Do not use
inappropriate or damaged soclets.
• To avoid electrical shock, plug the power cables into properly grounded
electrical outlets. If the device is equipped with a 3-pin power supply cord,
do not use adapters that do not have a grounding element or remove the
grounding element from the plug or adapter.
• Do not bend, crush or otherwise expose the power cord / power cord of the
appliance to mechanical stress or external heat sources. Damage to the power
cord may result in electric shock.
• If the power cord is damaged, disconnect the appliance from the mains and do
not use it again. If the power cord / power cord is damaged, it must be replaced
by the manufacturer, its service department, or a qualifi ed person to avoid the
risk of electric shock.
• Regularly check and maintain the electrical appliance as well as the power
cable. Disconnect the power plug regularly and clean it if necessary. Pollution
by dust or other substances may cause disruption of the insulating state and
consequently fi re.
• Do not expose the appliance to water or moisture. The ingress of water into
the appliance increases the risk of electric shock. If the power cord is wet
or the appliance gets water, disconnect it immediately from the mains. If the
appliance is plugged into a mains socket and if possible, turn off the power
supply before attempting to disconnect the power supply. If you are pulling wet
wires from a live power source, be very careful.
• If the electrical equipment is installed (connecting) the protective covers are
dismantled, the electrical parts must not be accessible to the user when the
installation is fi nished.
1.4 Safety of persons
• This appliance is intended for use by persons without an electrotechnical
qualifi cation (layperson) according to the instructions specifi ed by the
manufacturer.
• Device operation includes activities such as switching on and off, user
manipulation and setting of operating parameters, visual or auditory inspection
of the equipment, and user cleaning and maintenance.
• This appliance can be used by children 8 years of age and older and persons
with reduced physical, sensory or mental abilities or lack of experience and
knowledge only when under the supervision or guidance of the responsible
person have been instructed to use the appliance in a safe way and
understand the potential hazards .
• Cleaning and user maintenance can be carried out by children 8 years of age
and older only under the supervision of the responsible person.
• Children may not play with the appliance.
• Always keep the appliance out of reach of children during use and operation.
Be sure to download the appliance even for a freely accessible power cord.
• Always be careful when operating the electric appliance. Do not use an electric
appliance if you are overly tired, under the infl uence of medication or narcotic
drugs that reduce attention and focus. Inattention during operation may result
in serious injury.
5EN
1.5 Cleaning, maintenance and repairs
• Observe the normal user cleaning and maintenance of the appliance in
the recommended way. Do not use solvents or harsh cleaners for cleaning.
Pollution and visible stains from fi nger contact, respectively. The hands can
be cleaned using detergent detergents specially designed to clean household
appliances.
• If you do not use the appliance, clean it or disconnect the appliance from the
power supply when the appliance is faulty.
• Electrical appliances that are cleaned after use and are not intended to be
completely or partly immersed in water or other liquid, protect against the
effects of dripping and / or splashing water and before immersion.
• Electric household appliances, like all other technical devices, are subject to
the surrounding environment and natural wear. Since the legal framework of
regular maintenance is not laid down for lay-in electrical household appliances,
the manufacturer recommends that the user have the appliance checked and
cleaned at least once a year by a specialist workshop.
• By doing so, it is possible to achieve safety, operational reliability and
increased service life.
• Do not disassemble the electric appliance! The appliance works with a
dangerous voltage. For this reason, always switch off the appliance and
disconnect it from the mains supply during user maintenance. In the event of a
fault, please have the repair serviced by an authorized service center.
• Before calling a service:
1. Turn the appliance off and on to make sure the fault reappears.
2. If the malfunction of the appliance still persists after these operations, call
the nearest specialist service center.
• Never repair the electric appliance yourself!
• Unauthorized, unqualifi ed and improper use of an electric appliance may result
in electric shock or other serious injury.
• Only carry out the warranty or post-warranty repair of an electrical appliance to
an authorized qualifi ed person (*).
(*) Competent qualifi ed expert: the sales department of the manufacturer or importer or the person
qualifi ed and authorized to carry out this type of activity with the ability to avoid all risks.
6EN
2.Special safety instructions.
Read carefully!
• The electrical equipment is designed and manufactured in such a way as to
allow safe operation and use by unauthorized persons. Despite all precautions
taken by the manufacturer for safe use, operation and use entails certain
residual risks and the associated potential hazards.
• The following symbols and their meanings have been used on the device and
in the accompanying documentation to indicate potential hazards:
This symbol alerts users that the device is operating with hazardous
electrical voltages. Do not remove protective covers on the device.
Failure to follow the safety instructions while using and operating the
equipment may result in:
Risk of electric shock! Risk of serious injury or death!
This symbol warns users that if the safety instructions for using and
operating the device are not followed, there is a risk of: serious injury
or death!
Risk of equipment damage or other property damage!
This symbol warns the user that if the safety instructions for use and
operation of the device are not followed, there is a risk of burning from
a hot surface!
Transport/Carrying
• When using the transport trolley, be careful not to tip over the machine.
• Never carry the machine while it is in operation.
• Do not carry the device until all cable connections have been disconnected.
• Carry the device by grasping the handles or solid body parts.
Risk of serious injury or death! Risk of equipment damage!
Unpacking/Packaging
• Unpack the device and accessories before putting it into operation and remove
all parts of the packaging material, labels and tags. Store the packaging
materials in a safe place or keep them out of the reach of children and
incapacitated persons.
Risk of serious injury! Risk of suffocation!
Inspection/Commissioning
• The appliance is intended for food preparation. Therefore, thoroughly clean all
parts before commissioning, following the instructions in the “Commissioning”
section or “Cleaning” section.
• Never clean the device (its electrical unit with a heater) and the power cord
with plug in a way (under running water) that could cause liquid to fl ow into the
device.
• Clean these parts only with a damp cloth and wipe them dry or allow them to
dry.
• Only clean the unit when it is turned off and unplugged.
• We recommend performing initial and subsequent regular inspections of the
equipment.
• Never use the appliance if it is incomplete, damaged or any part of it has been
damaged during use.
7EN
• Do not use non-original and incomplete parts and accessories. Risk of electric
shock!
Risk of electric short circuit!
• Use the machine only with original accessories intended for use with the type.
Use only complete and fully assembled equipment.
Location/Installation
• Only place the appliance on a fl at, fi rm and stable surface - on the kitchen
worktops and on the furniture parts intended for the location of the kitchen
appliances.
• Always make sure that the area where you want to place the machine has
suffi cient space, mechanical strength, and adequate lighting.
Warning!
• Do not expose the device to:
- direct sunlight, heat-producing sources and equipment,
- vibration and mechanical stresses,
- excessive dust,
- water and excessive moisture,
- insect,
- aggressive external environment.
• Do not use or place the device:
- for unstable tables or furniture parts,
- on uneven and dirty surfaces,
- on the tight edge of tables or parts of furniture,
- in the vicinity of containers containing water or other liquids.
• Do not partially cover the device. Do not place any objects on the device.
Do not insert or allow foreign bodies to enter the openings of the machine’s
covers.
• Do not block the air vents of the covers. Air ventilation ensures correct, reliable
and safe operation of the device.
Risk of electric shock! Risk of fi re!
Warning!
• Place the device in a place where children cannot reach freely.
• Keep children away from the device. The device may fall over and cause
serious injury.
• Mechanical damage (rupture or breakage of parts and covers) of the device
can cause serious injury.
Risk of serious injury!
There is a risk of damage to the equipment or other property damage!
• Do not place or use this product near containers containing water. If the
device falls into the water, do not remove it! Unplug the power cord from the
wall outlet before removing the machine from the water. In such cases, take
the equipment to a professional service center to check that it is safe and
functioning properly.
Risk of electric shock! Risk of electric short circuit!
Operation/Supervision
• Keep the unit under supervision during use and operation!
• This unit is not intended to be operated by a programmer, external timer or
remote control, as there is a risk of fi re if it is covered or incorrectly positioned.
• Do not use this product near fl ammable materials or objects such as. curtains,
drapes, decorative fabrics, etc.
Risk of fi re!
8EN
Warning!
• The appliance must not be left unattended while it is connected to the mains!
Risk of electric shock! Risk of burns from hot surfaces!
• Make sure that the controller (main switch) is in the “0” (Off) position each time
the machine is connected to the mains.
• Do not turn the machine on or off by plugging in or unplugging the power cord.
• Always connect the machine to the wall outlet (wall socket) in normal use, and
then turn on the power switch.
• After use, turn off the machine with the power switch, and then unplug the
power cord.
• Do not use the machine if the power switch is not working.
• The equipment is under dangerous voltage when the AC power is connected.
Risk of electric shock! Risk of serious injury!
• The machine contains rotating parts - rotary pulling head.
Warning!
• Never put your fi ngers or other objects into the working area - inside the bowl
and near rotating parts while the machine is working.
• Be extremely careful not to come into contact with the rotary head when
turning cotton candy fi bers onto a wooden stick!
• In case of necessary manipulation in the working area (cleaning of rotating
parts from food residue) - always only when the machine is switched off,
disconnected from the power supply and if the rotating parts have stopped
completely, use only designated accessories of the machine or suitable object,
eg. plastic knife, plastic spatula. Do not use metal objects.
Warning!
• After the unit has been switched off, the rotating parts drive is still running for a
while. Always wait until the rotating parts have come to a complete stop before
handling the machine or the working area of the container.
Risk of serious injury!
• The device contains parts that become very hot during operation - a rotating
head with a heating element.
• Do not touch the rotating parts with your hands or any parts of the body and
the hot surface of the machine!
Risk of burns from hot surfaces!
Warning!
• After turning the unit off, the rotating head and the heating element remain hot
for some time. Before any further manipulation with the device - postponement
or always keep the hot parts of the device cool completely.
• Keep your face away from the working area of the machine’s container when
it is in operation. Keep away from loose and long hair, loose clothing or loose
decorative chains, etc. near the machine’s workspace.
Risk of serious injury!
There is a risk of damage to the equipment or other property damage!
• Never leave the machine free of charge and do not leave it with the power cord
freely accessible. Children could pull the device off the power cord.
Risk of serious injury!
• Never overload the device beyond the limits specifi ed in the technical data!
• Always divide the operating mode (operating time/operation and pause) of the
machine into the recommended working intervals and follow these instructions.
9EN
• If you notice any abnormal effects (sound, odor, smoke, ...) while using the
unit, turn off the unit immediately and unplug it from the wall outlet. Have the
device checked by a specialist garage.
• Only install and remove individual parts and accessories of the unit when the
unit is turned off and unplugged.
• Always clean the appliance thoroughly immediately after use and remove any
residues of food being processed.
• If any safety part/component (mechanical, electrical) is part of the device,
never put this part/component out of operation! Do not use the appliance if the
safety part/component is damaged or malfunctioning!
• Children under 3 years of age must be prevented from accessing the appliance
unless they are constantly supervised.
• Children from 3 years of age and under 8 years of age must not plug the
appliance in, regulate or clean it, or perform maintenance by the user.
• CAUTION: Some parts of this product may become very hot and cause burns.
Pay special attention when vulnerable persons or children are present.
• Never underestimate possible dangers and be careful !!!
10EN
A
B
C
D
E
F
Before fi rst use
Do not connect the device to the mains during preparation.
Unpack the device and remove all packaging material. To remove any dirt that
may have formed during the packaging process, clean the inside and the cover
with a dry, lint-free cloth. When cleaning sharp parts, be careful not to injure
yourself. (See section
„Cleaning and maintenance“ in this manual.)
Wash the pull-out rotary head assembly and the bowl in warm water.
Do not immerse the heating element in water! Clean the surface with a cloth
dampened in water.
Dry all parts thoroughly.
Never immerse the body of the device in water or any other liquid!
For home use only!
Description of parts
ň
A bowl cover
B bowl
C rotary head assembly
D body of the device
E mains switch 0/I
F indicators
G sugar measuring cup
G
11EN
Assembly and use of equipment
Follow these steps to set up and use your device.
1. Place the body of the device (D) on a dry, level and fi rm surface. Do not
plug the power cord into an electrical outlet before assembling the device
completely!
2. Slide the bowl (B) onto the device body (D) and then place the bowl cover
(A) on the bowl.
3. Fit the rotary head (C). Make sure that you
push the rotary head fi rmly downwards with
the groove and fi t it correctly. Improper seating
of the extraction head can cause cotton candy
production failure or excessive vibration.
4. Plug the power cord into an electrical outlet.
5. The READY indicator lights up.
6. Pour one scoop of pure granulated sugar into the center of the extraction
head so that it is spread evenly (you can also use a fl at tablespoon).
Notes
Do not give more than one scoop of sugar. Excessive sugar causes noise
or vibration.
Use only pure granulated sugar in this cotton candy machine.
The use of other sugar can cause cotton candy production to fail. Do not
use sugar mixed with other materials, such as coffee or powdered milk.
They will cause the extraction head to block.
Never use materials other than pure granulated sugar (eg salt).
7. Set switch 0/1 (E) to „on position - 1“ - the START-UP light comes on.
The head rotates and is heated by the heating unit.
8. Cotton candy starts to form in about 2 or 3 minutes.
Wrap the cotton candy on a wooden stick as
follows:
Hold the wooden stick in an upright position, turn it
a few times from the inside around the bowl. Then
place the wooden stick horizontally and rotate it
over the rotating head and the inner edge of the
bowl to wind the cotton candy.
9. When the cotton candy is ready, switch off the appliance by moving the
switch 0/1 (E) to the „off position - 0“.
10. To make another cotton candy, repeat the procedure in the same
sequence.
12EN
Note
The sugar only needs to be emptied after stopping the extraction head.
Recommendation
After making 3 to 4 cotton candy, we recommend wiping and removing the
accumulated sugar residues from the inside of the bowl.
Notifi cations!
• Do not pour sugar into the extraction head when the 0/1 switch is in the „on
position - 1“ and the head is rotating.
• Make sure you switch off the appliance after making cotton candy. When
the cotton candy in the device is made from sugar left in the extraction head
from a previous use, an extraction head imbalance may occur. This may
cause noise or vibration of the device, which may damage the device.
• The rotating head rotates at high temperature and high speed. Reduce the
risk of injury and never touch it with your hands, spoons or other objects.
• The temperature of the extraction head is still high for a short time (approx.
15 minutes) even after the appliance has been switched off and stopped. Do
not touch it with your hands, reduce the risk of burns.
• After turning off the machine, wait until the rotating head stops moving.
Do not stop it with any object. This may cause injury or damage to the
equipment.
• Make sure the bowl is properly seated.
• Do not use the device on a carpet.
• Do not put your hands in the bowl during operation.
• Keep your face away from the bowl during operation.
• Use the cotton candy machine within the room temperature range 10 °
C - 35 ° C. Cotton candy will not thrive at temperatures outside the optimal
range.
• Do not use the cotton candy machine where the air from the fan or air
conditioner blows directly on it, otherwise the cotton candy will not be wound
evenly.
• When carrying the appliance, always hold it by the body of the appliance,
not the bowl.
• Do not switch on the cotton candy machine without the rotating head in
place.
WARNING!
Do not pour the sugar out of the rotary head assembly, in which case the
sugar will stick inside the device, causing the sugar to burn and then smoke.
In this case, the device must be switched off, allowed to cool down and
cleaned.
Production of colored cotton candy
Use only approved food coloring in the production of colored cotton candy.
1. Pour 1 scoop of sugar into a small cup.
2. Add a small amount of food coloring to the sugar.
3. Shake the cup gently and mix the sugar with the food coloring.
4. Pour it into the rotary head and follow the instructions.
13EN
Cleaning and maintenance
Before cleaning, turn the machine off and unplug the power cord. Wash the
bowl, cover, and rotary head in warm soapy water, wipe and gently dry. Do not
leave parts wet.
Do not use solvents or abrasive cleaners to clean any elements.
Wash parts immediately after use to avoid sugar residue. Wash your head
with a dish brush.
Cleaning the bowl
1. Remove the bowl from the appliance body.
2. Wash the bowl in hot or warm water. Use a soft cloth for washing.
The brush would scratch the bowl surface. Wipe the surface dry.
Cleaning the Rotary Head Assembly
CAUTION
The rotary head assembly is still hot for about 15 minutes after switching off,
remove the head after cooling to avoid the risk of burns.
1. Wash the rotary head in hot or warm water. Soak it before washing to clean
it more easily. Use a soft cloth for cleaning.
2. Wipe the rotary head dry.
Note
Be careful when handling the head. Do not let it fall or bend it.
Sugar deposits can be quickly released by immersing the rotating head in hot
water.
Body cleaning equipment
Use a soft cloth to clean the unit body and the power cord. Do not clean them
with a brush, as a brush of any kind would scratch the surface of these parts.
Never immerse the device body in water or any other liquid! Wipe the body
and power cord with a dry cloth.
After cleaning and drying, re-assemble the bowl and pull-out head to its
original position.
WARNING
- Do not clean any part of the cotton candy machine with petrol, kerosene,
glass or furniture polish, or thinner.
- Do not spray water on the housing. There is a risk of electric shock and
damage to the electrical components of the machine.
- Do not disconnect the device if your hands are wet. This may result in
electric shock.
14EN
Technical specifi cations
Power supply: 220 - 240 V~ 50/60 Hz
Power consumption: 500 W
Dimensions (W x H x D): 27,5 x 26 x 27,5 mm
Weight: 1,45 kg
Noise: 65 dB (A)
The declared noise emission value of this appliance is 65 dB (A), which
represents the sound power level A with respect to the reference sound power
of 1 pW.
We reserve the right to make changes!
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
Dispose of used packaging material at a municipal waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the products or in the accompanying documents means that used
electrical and electronic products should not be mixed with general household waste.
For proper disposal, recovery and recycling, please return these products to designated
collection points. Alternatively, in some countries of the European Union or other
European countries, you may return your products to your local retailer when purchasing
an equivalent new product. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment natural resources and help
prevent potential negative effects on environment and human health, which could be the
consequences of improper disposal waste. Contact your local authority or nearest offi ce
for more details collection point. Improper disposal of this type of waste may result in
penalties in accordance with national regulations.
For business entities in the countries of the European Union
If you wish to discard electrical and electronic equipment, please request the necessary information
from your seller or supplier.
Disposal in other countries outside the European Union
This symbol is valid in the European Union. If you wish to discard this product, please request
obtain the necessary information on the correct method of disposal from the local authorities or from the
your supplier.
Producer:
Importer:
ORAVA retail 1, a.s.
Seberíniho 2
821 03 Bratislava
Slovenská republika
ORAVA distribution CZ, s.r.o.
Ostravská 494
739 25 Sviadnov
Česká republika
ORAVA retail 1, a.s.
Seberíniho 2
821 03 Bratislava
Slovenská republika
This product complies with all the essential requirements of the EU directives that apply to it.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Orava CM-551 User manual
- Category
- Small kitchen appliances
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Blaupunkt COBP6PB4U1 User manual
-
-
partyrent com 1798 User manual
-
Argos PMX-2301 User manual
-
Nostalgia Electrics CCM-527 User manual
-
-
ANKO Cotton Candy Maker CCM-500L User manual
-
AmeriHome CCMAKER User guide
-
Centurion SSR120 User manual
-
