Orava CM-551 User manual

Brand: Orava

Model: CM-551

Category: Small kitchen appliances

Type: User manual

Cotton candy device

CM-551

Instruction manual EN

2EN

Intended use of the device

The equipment is intended solely for the manufacture of cotton candy, from

pure crystal sugar (or similar crystalline sugar), to the extent determined

by technical and operational parameters and functions, safety and user

instructions, and external inﬂ uences of the operating environment.

ORAVA electrical appliances are manufactured according to state-of-the-art

knowledge and recognized safety regulations. Nevertheless, improper or

improper use or improper use may result in injury or endangerment to the life

of the user or a third party or to a third party. damage to equipment and other

property.

1. GENERAL SAFETY INSTRUCTIONS AND WARNINGS

• This document contains important safety instructions and warnings for safe,

correct and economical operation of the electrical equipment. Its compliance

helps the user avoid risks, increase reliability and product life.

• In this document, the generic term product is used in text parts such as:

electrical equipment - any device used for the production, conversion,

transmission, distribution or use of electricity.

• From the point of view of the purpose of using electricity, the concept of

electrical equipment in the strict sense of the word will include the following

categories:

- household electric appliances,

- information and communication equipment,

- consumer electronics,

- lighting equipment,

- electrical and electronic tools,

- toys and equipment for sporting and recreational

1.1 General safety instructions

• Before commissioning the unit, we recommend that you carefully read

the operating instructions and operate the equipment in accordance with the

instructions!

• The safety instructions and warnings in this manual do not cover all the

possible conditions and situations that may arise when using the device. The

user must understand that a factor that can not be incorporated into any of the

products is responsibility and caution. These factors must therefore be ensured

by users / users who use and operate this device.

• Failure to follow the safety instructions and warnings is forbidden by the

manufacturer for any damage to health or property!

• Make sure that the appliance is complete and shows no signs of damage

before using the appliance for the ﬁ rst time. If the product is defective or if it

has any visible damage, do not use the product.

• Keep the operating instructions as close to the device as possible throughout

its service life. Always keep the operating instructions together with the

appliance for future use and use by new users.

• Use the appliance only for the purpose for which it is intended and in the

manner speciﬁ ed by the manufacturer.

• The appliance is intended for home and similar indoor use, with no special

focus.

3EN

• It is not a professional device for commercial use.

• Do not change the technical parameters and features of the device by

unauthorized modiﬁ cation or modiﬁ cation of any part of the device.

• The manufacturer is not responsible for damages caused during

transportation, misuse, damage or destruction of the equipment due to

adverse weather conditions.

1.2 Safety of the operating environment

• Do not use the device in an industrial environment or outside environment.

• Always keep the operating environment clean and well lit.

• Do not place the device on an unstable surface. Overriding or dropping the

device may result in personal injury or damage to the device.

• Do not expose the unit to direct sunlight or excessive heat sources.

• Do not use an electric appliance in areas with ﬂ ammable liquids, gases or dust.

The appliance may be the source of scaling, which can result in the ignition of

dust or vapors.

Features of the operating environment

1. Ambient temperature: +5 ÷ +40 ° C

2. Humidity: 5 ÷ 85%

3. Altitude: ≤ 2 000 m

4. Occurrence of water: intermittent condensation of water or occurrence of water

vapor

5. Occurrence of foreign bodies: amount and type of dust are not signiﬁ cant

Protection class: IP20

• Other characteristics of the operating environment (mechanical stress

- shocks and vibrations, occurrence of plant, animals, weather effects) are

negligible in terms of effect on the correct and safe use of electrical equipment.

1.3 Electrical safety

• Before connecting the appliance to the power supply for the ﬁ rst time, make

sure that the voltage on the appliance label corresponds to that of the

household electrical outlet.

• The electrical appliance is designed for mains supply 230 V ~.

The electrical safety of the appliance is guaranteed only if it is properly

connected to the electricity grid.

• Only use a power cord with a plug (mains lead) that came with the device and

compatible with a wall outlet. Using another cable may result in ﬁ re or electric

shock.

• Always connect an electrical appliance to an easily accessible power outlet. In

the event of an operating fault, the appliance must be switched off as soon as

possible and disconnected from mains supply.

• Do not pull the power cord / power cord by pulling on the cord / cord.

Disconnect the power cord by pulling the plug behind the power cord / power

cord plug.

• If you use an extension cord, check that the total rated (ampere) power of

all devices connected to the extension cord does not exceed the maximum

current rating of the extension cable.

• If you need to use an extension cord or power supply block, make sure that

the extension cord or power pack is plugged into a power outlet, and not to

another extension cord or power supply. Extension power cord or power supply

block must be designed for grounded plugs and plugged into a grounded

outlet.

4EN

• The power plug of the appliance must be compatible with the mains socket.

Never use any adapters or modify the socket in any other way. Do not use

inappropriate or damaged soclets.

• To avoid electrical shock, plug the power cables into properly grounded

electrical outlets. If the device is equipped with a 3-pin power supply cord,

do not use adapters that do not have a grounding element or remove the

grounding element from the plug or adapter.

• Do not bend, crush or otherwise expose the power cord / power cord of the

appliance to mechanical stress or external heat sources. Damage to the power

cord may result in electric shock.

• If the power cord is damaged, disconnect the appliance from the mains and do

not use it again. If the power cord / power cord is damaged, it must be replaced

by the manufacturer, its service department, or a qualiﬁ ed person to avoid the

risk of electric shock.

• Regularly check and maintain the electrical appliance as well as the power

cable. Disconnect the power plug regularly and clean it if necessary. Pollution

by dust or other substances may cause disruption of the insulating state and

consequently ﬁ re.

• Do not expose the appliance to water or moisture. The ingress of water into

the appliance increases the risk of electric shock. If the power cord is wet

or the appliance gets water, disconnect it immediately from the mains. If the

appliance is plugged into a mains socket and if possible, turn off the power

supply before attempting to disconnect the power supply. If you are pulling wet

wires from a live power source, be very careful.

• If the electrical equipment is installed (connecting) the protective covers are

dismantled, the electrical parts must not be accessible to the user when the

installation is ﬁ nished.

1.4 Safety of persons

• This appliance is intended for use by persons without an electrotechnical

qualiﬁ cation (layperson) according to the instructions speciﬁ ed by the

manufacturer.

• Device operation includes activities such as switching on and off, user

manipulation and setting of operating parameters, visual or auditory inspection

of the equipment, and user cleaning and maintenance.

• This appliance can be used by children 8 years of age and older and persons

with reduced physical, sensory or mental abilities or lack of experience and

knowledge only when under the supervision or guidance of the responsible

person have been instructed to use the appliance in a safe way and

understand the potential hazards .

• Cleaning and user maintenance can be carried out by children 8 years of age

and older only under the supervision of the responsible person.

• Children may not play with the appliance.

• Always keep the appliance out of reach of children during use and operation.

Be sure to download the appliance even for a freely accessible power cord.

• Always be careful when operating the electric appliance. Do not use an electric

appliance if you are overly tired, under the inﬂ uence of medication or narcotic

drugs that reduce attention and focus. Inattention during operation may result

in serious injury.

5EN

1.5 Cleaning, maintenance and repairs

• Observe the normal user cleaning and maintenance of the appliance in

the recommended way. Do not use solvents or harsh cleaners for cleaning.

Pollution and visible stains from ﬁ nger contact, respectively. The hands can

be cleaned using detergent detergents specially designed to clean household

appliances.

• If you do not use the appliance, clean it or disconnect the appliance from the

power supply when the appliance is faulty.

• Electrical appliances that are cleaned after use and are not intended to be

completely or partly immersed in water or other liquid, protect against the

effects of dripping and / or splashing water and before immersion.

• Electric household appliances, like all other technical devices, are subject to

the surrounding environment and natural wear. Since the legal framework of

regular maintenance is not laid down for lay-in electrical household appliances,

the manufacturer recommends that the user have the appliance checked and

cleaned at least once a year by a specialist workshop.

• By doing so, it is possible to achieve safety, operational reliability and

increased service life.

• Do not disassemble the electric appliance! The appliance works with a

dangerous voltage. For this reason, always switch off the appliance and

disconnect it from the mains supply during user maintenance. In the event of a

fault, please have the repair serviced by an authorized service center.

• Before calling a service:

1. Turn the appliance off and on to make sure the fault reappears.

2. If the malfunction of the appliance still persists after these operations, call

the nearest specialist service center.

• Never repair the electric appliance yourself!

• Unauthorized, unqualiﬁ ed and improper use of an electric appliance may result

in electric shock or other serious injury.

• Only carry out the warranty or post-warranty repair of an electrical appliance to

an authorized qualiﬁ ed person (*).

(*) Competent qualiﬁ ed expert: the sales department of the manufacturer or importer or the person

qualiﬁ ed and authorized to carry out this type of activity with the ability to avoid all risks.

6EN

2.Special safety instructions.

Read carefully!

• The electrical equipment is designed and manufactured in such a way as to

allow safe operation and use by unauthorized persons. Despite all precautions

taken by the manufacturer for safe use, operation and use entails certain

residual risks and the associated potential hazards.

• The following symbols and their meanings have been used on the device and

in the accompanying documentation to indicate potential hazards:

This symbol alerts users that the device is operating with hazardous

electrical voltages. Do not remove protective covers on the device.

Failure to follow the safety instructions while using and operating the

equipment may result in:

Risk of electric shock! Risk of serious injury or death!

This symbol warns users that if the safety instructions for using and

operating the device are not followed, there is a risk of: serious injury

or death!

Risk of equipment damage or other property damage!

This symbol warns the user that if the safety instructions for use and

operation of the device are not followed, there is a risk of burning from

a hot surface!

Transport/Carrying

• When using the transport trolley, be careful not to tip over the machine.

• Never carry the machine while it is in operation.

• Do not carry the device until all cable connections have been disconnected.

• Carry the device by grasping the handles or solid body parts.

Risk of serious injury or death! Risk of equipment damage!

Unpacking/Packaging

• Unpack the device and accessories before putting it into operation and remove

all parts of the packaging material, labels and tags. Store the packaging

materials in a safe place or keep them out of the reach of children and

incapacitated persons.

Risk of serious injury! Risk of suffocation!

Inspection/Commissioning

• The appliance is intended for food preparation. Therefore, thoroughly clean all

parts before commissioning, following the instructions in the “Commissioning”

section or “Cleaning” section.

• Never clean the device (its electrical unit with a heater) and the power cord

with plug in a way (under running water) that could cause liquid to ﬂ ow into the

device.

• Clean these parts only with a damp cloth and wipe them dry or allow them to

dry.

• Only clean the unit when it is turned off and unplugged.

• We recommend performing initial and subsequent regular inspections of the

equipment.

• Never use the appliance if it is incomplete, damaged or any part of it has been

damaged during use.

7EN

• Do not use non-original and incomplete parts and accessories. Risk of electric

shock!

Risk of electric short circuit!

• Use the machine only with original accessories intended for use with the type.

Use only complete and fully assembled equipment.

Location/Installation

• Only place the appliance on a ﬂ at, ﬁ rm and stable surface - on the kitchen

worktops and on the furniture parts intended for the location of the kitchen

appliances.

• Always make sure that the area where you want to place the machine has

sufﬁ cient space, mechanical strength, and adequate lighting.

Warning!

• Do not expose the device to:

- direct sunlight, heat-producing sources and equipment,

- vibration and mechanical stresses,

- excessive dust,

- water and excessive moisture,

- insect,

- aggressive external environment.

• Do not use or place the device:

- for unstable tables or furniture parts,

- on uneven and dirty surfaces,

- on the tight edge of tables or parts of furniture,

- in the vicinity of containers containing water or other liquids.

• Do not partially cover the device. Do not place any objects on the device.

Do not insert or allow foreign bodies to enter the openings of the machine’s

covers.

• Do not block the air vents of the covers. Air ventilation ensures correct, reliable

and safe operation of the device.

Risk of electric shock! Risk of ﬁ re!

Warning!

• Place the device in a place where children cannot reach freely.

• Keep children away from the device. The device may fall over and cause

serious injury.

• Mechanical damage (rupture or breakage of parts and covers) of the device

can cause serious injury.

Risk of serious injury!

There is a risk of damage to the equipment or other property damage!

• Do not place or use this product near containers containing water. If the

device falls into the water, do not remove it! Unplug the power cord from the

wall outlet before removing the machine from the water. In such cases, take

the equipment to a professional service center to check that it is safe and

functioning properly.

Risk of electric shock! Risk of electric short circuit!

Operation/Supervision

• Keep the unit under supervision during use and operation!

• This unit is not intended to be operated by a programmer, external timer or

remote control, as there is a risk of ﬁ re if it is covered or incorrectly positioned.

• Do not use this product near ﬂ ammable materials or objects such as. curtains,

drapes, decorative fabrics, etc.

Risk of ﬁ re!

8EN

Warning!

• The appliance must not be left unattended while it is connected to the mains!

Risk of electric shock! Risk of burns from hot surfaces!

• Make sure that the controller (main switch) is in the “0” (Off) position each time

the machine is connected to the mains.

• Do not turn the machine on or off by plugging in or unplugging the power cord.

• Always connect the machine to the wall outlet (wall socket) in normal use, and

then turn on the power switch.

• After use, turn off the machine with the power switch, and then unplug the

power cord.

• Do not use the machine if the power switch is not working.

• The equipment is under dangerous voltage when the AC power is connected.

Risk of electric shock! Risk of serious injury!

• The machine contains rotating parts - rotary pulling head.

Warning!

• Never put your ﬁ ngers or other objects into the working area - inside the bowl

and near rotating parts while the machine is working.

• Be extremely careful not to come into contact with the rotary head when

turning cotton candy ﬁ bers onto a wooden stick!

• In case of necessary manipulation in the working area (cleaning of rotating

parts from food residue) - always only when the machine is switched off,

disconnected from the power supply and if the rotating parts have stopped

completely, use only designated accessories of the machine or suitable object,

eg. plastic knife, plastic spatula. Do not use metal objects.

Warning!

• After the unit has been switched off, the rotating parts drive is still running for a

while. Always wait until the rotating parts have come to a complete stop before

handling the machine or the working area of the container.

Risk of serious injury!

• The device contains parts that become very hot during operation - a rotating

head with a heating element.

• Do not touch the rotating parts with your hands or any parts of the body and

the hot surface of the machine!

Risk of burns from hot surfaces!

Warning!

• After turning the unit off, the rotating head and the heating element remain hot

for some time. Before any further manipulation with the device - postponement

or always keep the hot parts of the device cool completely.

• Keep your face away from the working area of the machine’s container when

it is in operation. Keep away from loose and long hair, loose clothing or loose

decorative chains, etc. near the machine’s workspace.

Risk of serious injury!

There is a risk of damage to the equipment or other property damage!

• Never leave the machine free of charge and do not leave it with the power cord

freely accessible. Children could pull the device off the power cord.

Risk of serious injury!

• Never overload the device beyond the limits speciﬁ ed in the technical data!

• Always divide the operating mode (operating time/operation and pause) of the

machine into the recommended working intervals and follow these instructions.

9EN

• If you notice any abnormal effects (sound, odor, smoke, ...) while using the

unit, turn off the unit immediately and unplug it from the wall outlet. Have the

device checked by a specialist garage.

• Only install and remove individual parts and accessories of the unit when the

unit is turned off and unplugged.

• Always clean the appliance thoroughly immediately after use and remove any

residues of food being processed.

• If any safety part/component (mechanical, electrical) is part of the device,

never put this part/component out of operation! Do not use the appliance if the

safety part/component is damaged or malfunctioning!

• Children under 3 years of age must be prevented from accessing the appliance

unless they are constantly supervised.

• Children from 3 years of age and under 8 years of age must not plug the

appliance in, regulate or clean it, or perform maintenance by the user.

• CAUTION: Some parts of this product may become very hot and cause burns.

Pay special attention when vulnerable persons or children are present.

• Never underestimate possible dangers and be careful !!!

10EN

Before ﬁ rst use

Do not connect the device to the mains during preparation.

Unpack the device and remove all packaging material. To remove any dirt that

may have formed during the packaging process, clean the inside and the cover

with a dry, lint-free cloth. When cleaning sharp parts, be careful not to injure

yourself. (See section

„Cleaning and maintenance“ in this manual.)

Wash the pull-out rotary head assembly and the bowl in warm water.

Do not immerse the heating element in water! Clean the surface with a cloth

dampened in water.

Dry all parts thoroughly.

Never immerse the body of the device in water or any other liquid!

For home use only!

Description of parts

A bowl cover

B bowl

C rotary head assembly

D body of the device

E mains switch 0/I

F indicators

G sugar measuring cup

11EN

Assembly and use of equipment

Follow these steps to set up and use your device.

1. Place the body of the device (D) on a dry, level and ﬁ rm surface. Do not

plug the power cord into an electrical outlet before assembling the device

completely!

2. Slide the bowl (B) onto the device body (D) and then place the bowl cover

(A) on the bowl.

3. Fit the rotary head (C). Make sure that you

push the rotary head ﬁ rmly downwards with

the groove and ﬁ t it correctly. Improper seating

of the extraction head can cause cotton candy

production failure or excessive vibration.

4. Plug the power cord into an electrical outlet.

5. The READY indicator lights up.

6. Pour one scoop of pure granulated sugar into the center of the extraction

head so that it is spread evenly (you can also use a ﬂ at tablespoon).

Notes

Do not give more than one scoop of sugar. Excessive sugar causes noise

or vibration.

Use only pure granulated sugar in this cotton candy machine.

The use of other sugar can cause cotton candy production to fail. Do not

use sugar mixed with other materials, such as coffee or powdered milk.

They will cause the extraction head to block.

Never use materials other than pure granulated sugar (eg salt).

7. Set switch 0/1 (E) to „on position - 1“ - the START-UP light comes on.

The head rotates and is heated by the heating unit.

8. Cotton candy starts to form in about 2 or 3 minutes.

Wrap the cotton candy on a wooden stick as

follows:

Hold the wooden stick in an upright position, turn it

a few times from the inside around the bowl. Then

place the wooden stick horizontally and rotate it

over the rotating head and the inner edge of the

bowl to wind the cotton candy.

9. When the cotton candy is ready, switch off the appliance by moving the

switch 0/1 (E) to the „off position - 0“.

10. To make another cotton candy, repeat the procedure in the same

sequence.

12EN

Note

The sugar only needs to be emptied after stopping the extraction head.

Recommendation

After making 3 to 4 cotton candy, we recommend wiping and removing the

accumulated sugar residues from the inside of the bowl.

Notiﬁ cations!

• Do not pour sugar into the extraction head when the 0/1 switch is in the „on

position - 1“ and the head is rotating.

• Make sure you switch off the appliance after making cotton candy. When

the cotton candy in the device is made from sugar left in the extraction head

from a previous use, an extraction head imbalance may occur. This may

cause noise or vibration of the device, which may damage the device.

• The rotating head rotates at high temperature and high speed. Reduce the

risk of injury and never touch it with your hands, spoons or other objects.

• The temperature of the extraction head is still high for a short time (approx.

15 minutes) even after the appliance has been switched off and stopped. Do

not touch it with your hands, reduce the risk of burns.

• After turning off the machine, wait until the rotating head stops moving.

Do not stop it with any object. This may cause injury or damage to the

equipment.

• Make sure the bowl is properly seated.

• Do not use the device on a carpet.

• Do not put your hands in the bowl during operation.

• Keep your face away from the bowl during operation.

• Use the cotton candy machine within the room temperature range 10 °

C - 35 ° C. Cotton candy will not thrive at temperatures outside the optimal

range.

• Do not use the cotton candy machine where the air from the fan or air

conditioner blows directly on it, otherwise the cotton candy will not be wound

evenly.

• When carrying the appliance, always hold it by the body of the appliance,

not the bowl.

• Do not switch on the cotton candy machine without the rotating head in

place.

WARNING!

Do not pour the sugar out of the rotary head assembly, in which case the

sugar will stick inside the device, causing the sugar to burn and then smoke.

In this case, the device must be switched off, allowed to cool down and

cleaned.

Production of colored cotton candy

Use only approved food coloring in the production of colored cotton candy.

1. Pour 1 scoop of sugar into a small cup.

2. Add a small amount of food coloring to the sugar.

3. Shake the cup gently and mix the sugar with the food coloring.

4. Pour it into the rotary head and follow the instructions.

13EN

Cleaning and maintenance

Before cleaning, turn the machine off and unplug the power cord. Wash the

bowl, cover, and rotary head in warm soapy water, wipe and gently dry. Do not

leave parts wet.

Do not use solvents or abrasive cleaners to clean any elements.

Wash parts immediately after use to avoid sugar residue. Wash your head

with a dish brush.

Cleaning the bowl

1. Remove the bowl from the appliance body.

2. Wash the bowl in hot or warm water. Use a soft cloth for washing.

The brush would scratch the bowl surface. Wipe the surface dry.

Cleaning the Rotary Head Assembly

CAUTION

The rotary head assembly is still hot for about 15 minutes after switching off,

remove the head after cooling to avoid the risk of burns.

1. Wash the rotary head in hot or warm water. Soak it before washing to clean

it more easily. Use a soft cloth for cleaning.

2. Wipe the rotary head dry.

Note

Be careful when handling the head. Do not let it fall or bend it.

Sugar deposits can be quickly released by immersing the rotating head in hot

water.

Body cleaning equipment

Use a soft cloth to clean the unit body and the power cord. Do not clean them

with a brush, as a brush of any kind would scratch the surface of these parts.

Never immerse the device body in water or any other liquid! Wipe the body

and power cord with a dry cloth.

After cleaning and drying, re-assemble the bowl and pull-out head to its

original position.

WARNING

- Do not clean any part of the cotton candy machine with petrol, kerosene,

glass or furniture polish, or thinner.

- Do not spray water on the housing. There is a risk of electric shock and

damage to the electrical components of the machine.

- Do not disconnect the device if your hands are wet. This may result in

electric shock.

14EN

Technical speciﬁ cations

Power supply: 220 - 240 V~ 50/60 Hz

Power consumption: 500 W

Dimensions (W x H x D): 27,5 x 26 x 27,5 mm

Weight: 1,45 kg

Noise: 65 dB (A)

The declared noise emission value of this appliance is 65 dB (A), which

represents the sound power level A with respect to the reference sound power

of 1 pW.

We reserve the right to make changes!

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING

Dispose of used packaging material at a municipal waste disposal site.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

This symbol on the products or in the accompanying documents means that used

electrical and electronic products should not be mixed with general household waste.

For proper disposal, recovery and recycling, please return these products to designated

collection points. Alternatively, in some countries of the European Union or other

European countries, you may return your products to your local retailer when purchasing

an equivalent new product. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment natural resources and help

prevent potential negative effects on environment and human health, which could be the

consequences of improper disposal waste. Contact your local authority or nearest ofﬁ ce

for more details collection point. Improper disposal of this type of waste may result in

penalties in accordance with national regulations.

For business entities in the countries of the European Union

If you wish to discard electrical and electronic equipment, please request the necessary information

from your seller or supplier.

Disposal in other countries outside the European Union

This symbol is valid in the European Union. If you wish to discard this product, please request

obtain the necessary information on the correct method of disposal from the local authorities or from the

your supplier.

Producer:

Importer:

ORAVA retail 1, a.s.

Seberíniho 2

821 03 Bratislava

Slovenská republika

ORAVA distribution CZ, s.r.o.

Ostravská 494

739 25 Sviadnov

Česká republika

ORAVA retail 1, a.s.

Seberíniho 2

821 03 Bratislava

Slovenská republika

This product complies with all the essential requirements of the EU directives that apply to it.

Orava CM-551 User manual

Brand: Orava

Model: CM-551

Category: Small kitchen appliances

Type: User manual

Download PDF

report

Orava CM-551 User manual

Orava CM-551 User manual

Related papers

Other documents