MODEL T33150/T33151
ADVANCED HANGING
AIR FILTERS
OWNER'S MANUAL
(For models manufactured since 03/22)
T33150
T33151
COPYRIGHT © MARCH, 2022 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#SS22175 PRINTED IN TAIWAN V1.03.22
***Keep for Future Reference***
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION ............................................................................................................................... 2
Contact Info ................................................................................................................................ 2
Manual Accuracy ........................................................................................................................ 2
Identification ............................................................................................................................... 3
Controls & Components ............................................................................................................. 4
Machine Data Sheet (T33150) ................................................................................................... 6
Machine Data Sheet (T33151) ................................................................................................... 8
SECTION 1: SAFETY ..................................................................................................................... 10
Safety Instructions for Machinery ............................................................................................. 10
Additional Safety for Air Filters ................................................................................................. 12
SECTION 2: POWER SUPPLY ...................................................................................................... 13
SECTION 3: SETUP ....................................................................................................................... 15
Unpacking ................................................................................................................................ 15
Needed for Setup ..................................................................................................................... 15
Inventory ................................................................................................................................... 15
T33150 Assembly..................................................................................................................... 16
Site Considerations .................................................................................................................. 16
Test Run ................................................................................................................................... 17
Site Planning ............................................................................................................................ 18
Installing Air Filter ..................................................................................................................... 19
SECTION 4: OPERATIONS ........................................................................................................... 22
Operation Overview.................................................................................................................. 22
General ..................................................................................................................................... 22
Filtering Performance ............................................................................................................... 23
SECTION 5: ACCESSORIES ......................................................................................................... 24
SECTION 6: MAINTENANCE......................................................................................................... 26
Schedule .................................................................................................................................. 26
Cleaning/Replacing Filters ....................................................................................................... 26
Replacing Remote Control Batteries ........................................................................................ 27
Machine Storage ...................................................................................................................... 27
SECTION 7: SERVICE ................................................................................................................... 28
Troubleshooting ........................................................................................................................ 28
SECTION 8: WIRING ...................................................................................................................... 29
Wiring Safety Instructions ........................................................................................................ 29
T33150 Wiring Diagram ........................................................................................................... 30
T33151 Wiring Diagram ........................................................................................................... 31
SECTION 9: PARTS ....................................................................................................................... 32
T33150 Main ............................................................................................................................ 32
T33151 Main ............................................................................................................................ 34
T33150 Labels & Cosmetics .................................................................................................... 35
T33151 Labels & Cosmetics .................................................................................................... 36
WARRANTY & RETURNS ............................................................................................................. 37
-2- Model T33150/T33151 (Mfd. Since 03/22)
We stand behind our machines! If you have ques-
tions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number
and manufacture date
from the
machine ID label. This will help us help you faster.
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: (570) 546-9663
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We
made every effort to be exact with the
instruc-
tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that
sometimes the machine
you receive is
slightly different than shown in the manual
.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something
,
check our
website for an updated version. W
e post
current
manuals and
manual updates for free
on our web-
site at
www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write
down the
manufacture date and
serial number
from the machine ID label (see below). This
information is required for us to provide proper
tech support, and it helps us determine if updated
documentation is available for your machine.
Manufacture Date
Serial Number
Manual Accuracy
INTRODUCTION
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, serious
personal injury may occur.
Model T33150/T33151 (Mfd. Since 03/22) -3-
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Identification
Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.
Handle
Control Panel
Eye
Bolt
Lock Knob
Exhaust
Port & Filter
Access Door
Remote
Control
Secondary/
Activated
Carbon Filter
(Model T33151 shown)
Primary/
HEPA
Filter
Pre-Filter
-4- Model T33150/T33151 (Mfd. Since 03/22)
Controls &
Components
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Control Panel
Figure 1. Control panel.
A
Refer to the following figures and descriptions to
become familiar with the basic controls and com-
ponents of this machine. Understanding these
items and how they work will help you understand
the rest of the manual and minimize your risk of
injury when operating this machine.
A. Digital Readout: Displays time setting or fan
speed setting (depending on which indicator
is illuminated).
B. Air Quality Sensors: Detect amount of
particulate matter (PM2.5) and/or volatile
organic compounds (VOC) in air.
G
I
H
C. Filter 1 Indicator: Remains blue during nor-
mal operations. Turns red after 300 hours
run-time to indicate HEPA filter must be
replaced.
D. Filter 2 Indicator: Remains blue during nor-
mal operations. Turns red after 600 hours
run-time to indicate activated carbon filter
must be replaced.
E. Air QUALITY Indicator: Illumination cycles
between green, orange, and red as changing
levels of particulate matter (PM2.5) and vola-
tile organic compounds (VOC) are detected
by air quality sensors. Green is lowest level;
red is highest level.
F. on/off Button: Powers machine ON and
OFF.
G. Auto Indicator: Illuminates when fan speed
has been set to automatic mode. In this
mode, machine will automatically adjust fan
speed according to air quality, with fan speed
increasing as air quality worsens. As air qual-
ity improves, fan speed will automatically
decrease.
H. Fan Indicator: Illuminates when fan speed
setting is displayed on digital readout.
I. Time Indicator: Illuminates when time set-
ting is displayed on digital readout.
C
B
DE
F
Model T33150/T33151 (Mfd. Since 03/22) -5-
Remote Control
Figure 2. Remote control.
J. AUTO on/off Button: Turns automatic fan
speed setting ON or OFF.
K. on/off Button: Powers machine ON or OFF.
L. Fan Button: Cycles through fan speed set-
tings as indicated on digital readout.
— T33150: Speed settings 1 (400 CFM),
2 (500 CFM), and 3 (620 CFM).
— T33151: Speed settings 1 (800 CFM),
2 (1000 CFM), 3 (1200 CFM), 4 (1300
CFM), and 5 (1400 CFM).
M. Filter 2 Reset Button (FR2): Resets Filter
2 Indicator Light on control panel after acti-
vated carbon filter has been replaced. Press
FR2 button on remote control and hold for 5
seconds. Machine will beep and light on con-
trol panel will turn blue.
JK
M
L
N
O
N. Filter 1 Reset Button (FR1): Resets FIlter 1
Indicator Light on control panel after HEPA
filter has been replaced. Press FR1 button
on remote control and hold down for 5 sec-
onds. Machine will beep and light on control
panel will turn blue.
O. Time Button: Cycles through time settings
as indicated on digital readout. Time settings
are 2 hours (2), 4 hours (4), 6 hours (6), 8
hours (8), and indefinite (blank). If left on
indefinite, machine digital readout will return
to indicating fan speed.
Exhaust Port & Filter Access Door
Q
Figure 3. Exhaust port on T33150.
P. Exhaust Port: Location where filtered air
exits machine.
Q. Filter Access Door: Unscrew knobs to
access secondary activated carbon filter.
P
-6- Model T33150/T33151 (Mfd. Since 03/22)
The information contained herein is deemed accurate as of 9/26/2022 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2
Model T33150
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL T33150 3‐SPEED HEPA HANGING AIR FILTER
Product Dimensions:
Weight................................................................................................................................................................ 34 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................ 17-1/2 x 21-1/2 x 12-1/2 in.
Footprint (Length x Width)............................................................................................................... 21-1/2 x 17-1/2 in.
Shipping Dimensions:
Type............................................................................................................................................................. Cardboard
Content........................................................................................................................................................... Machine
Weight................................................................................................................................................................ 36 lbs.
Length x Width x Height....................................................................................................................... 22 x 14 x 26 in.
Electrical:
Power Requirement........................................................................................................... 110V, Single-Phase, 60 Hz
Full-Load Current Rating.......................................................................................................................................... 2A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length.............................................................................................................................................. 72 in.
Power Cord Gauge......................................................................................................................................... 18 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 5-15
Switch Type............................................................................................................... Control Panel & Remote Control
Motors:
Main
Horsepower............................................................................................................................................. 1/6 HP
Phase............................................................................................................................................ Single-Phase
Amps.............................................................................................................................................................. 2A
Speed............................................................................................................................ 1100, 1500, 1870 RPM
Type..................................................................................................................................................... Induction
Bearings........................................................................................................ Sealed & Permanently Lubricated
Main Specifications:
Operation
Dust Collector Type............................................................................................................................... Air Filter
Approved Dust Types........................................................................................................................ Particulate
Filter Type................................................................................................................................. Pleated, Panels
Airflow Performance............................................................................................................ 400, 500, 620 CFM
Machine Data Sheet (T33150)
Model T33150/T33151 (Mfd. Since 03/22) -7-
The information contained herein is deemed accurate as of 9/26/2022 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2
Model T33150
Filter Information
Number of Filters.............................................................................................................................................. 3
Filtration Rating................................................................................................................................ 0.3 Microns
Pre-Filter Type............................................................................................................................ Pleated Cotton
Pre-Filter Length.................................................................................................................................. 16-3/8 in.
Pre-Filter Width............................................................................................................................................ 7 in.
Pre-Filter Thickness................................................................................................................................ 3/16 in.
Primary Filter Type................................................................................................................................... HEPA
Primary Filter Rating....................................................................................................... 99.97% at 0.3 Microns
Primary Filter Length.............................................................................................................................. 415mm
Primary Filter Width................................................................................................................................ 178mm
Primary Filter Thickness........................................................................................................................... 27mm
Secondary Filter Type............................................................................................................. Activated Carbon
Secondary Filter Rating.................................................................................................................... 10 Microns
Secondary Filter Length......................................................................................................................... 280mm
Secondary Filter Width........................................................................................................................... 182mm
Secondary Filter Thickness...................................................................................................................... 22mm
Impeller Information
Impeller Type.............................................................................................................................................. Steel
Impeller Size.............................................................................................................................. 5-1/4 x 8-1/4 in.
Construction
Impeller....................................................................................................................................................... Steel
Paint Type/Finish....................................................................................................................... Powder Coated
Body........................................................................................................................................................... Steel
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ........................................................................................................ 30 Minutes
ISO 9001 Factory .................................................................................................................................................. Yes
Features:
Remote Control
Three-Stage Filtration
Three Fan Speeds
Hanging Mounts
Rubber Feet for Benchtop Mount
Primary Filter: 99.97% at 0.3 Microns (MERV-17 HEPA)
Secondary Filter: 10 Microns
Pre-Filter
-8- Model T33150/T33151 (Mfd. Since 03/22)
The information contained herein is deemed accurate as of 9/26/2022 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2
Model T33151
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL T33151 5‐SPEED HEPA HANGING AIR FILTER
Product Dimensions:
Weight................................................................................................................................................................ 64 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................ 20-1/2 x 27-1/2 x 20-1/2 in.
Footprint (Length x Width)............................................................................................................... 27-1/2 x 20-1/2 in.
Shipping Dimensions:
Type............................................................................................................................................................. Cardboard
Content........................................................................................................................................................... Machine
Weight................................................................................................................................................................ 68 lbs.
Length x Width x Height....................................................................................................................... 25 x 23 x 31 in.
Electrical:
Power Requirement........................................................................................................... 110V, Single-Phase, 60 Hz
Full-Load Current Rating....................................................................................................................................... 2.8A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length.............................................................................................................................................. 72 in.
Power Cord Gauge......................................................................................................................................... 18 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 5-15
Switch Type............................................................................................................... Control Panel & Remote Control
Motors:
Main
Horsepower............................................................................................................................................. 1/3 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 2.8A
Speed.................................................................................................................. 480, 560, 640, 730, 820 RPM
Type..................................................................................................................................................... Induction
Bearings........................................................................................................ Sealed & Permanently Lubricated
Main Specifications:
Operation
Dust Collector Type............................................................................................................................... Air Filter
Approved Dust Types........................................................................................................................ Particulate
Filter Type................................................................................................................................. Pleated, Panels
Airflow Performance.................................................................................... 800, 1000, 1200, 1300, 1400 CFM
Machine Data Sheet (T33151)
Model T33150/T33151 (Mfd. Since 03/22) -9-
The information contained herein is deemed accurate as of 9/26/2022 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2
Model T33151
Filter Information
Number of Filters.............................................................................................................................................. 3
Filtration Rating................................................................................................................................ 0.3 Microns
Pre-Filter Type............................................................................................................................ Pleated Cotton
Pre-Filter Length.................................................................................................................................. 19-3/8 in.
Pre-Filter Width.................................................................................................................................... 15-3/8 in.
Pre-Filter Thickness................................................................................................................................ 3/16 in.
Primary Filter Type................................................................................................................................... HEPA
Primary Filter Rating....................................................................................................... 99.97% at 0.3 Microns
Primary Filter Length.............................................................................................................................. 391mm
Primary Filter Width................................................................................................................................ 492mm
Primary Filter Thickness........................................................................................................................... 27mm
Secondary Filter Type............................................................................................................. Activated Carbon
Secondary Filter Rating.................................................................................................................... 10 Microns
Secondary Filter Length......................................................................................................................... 370mm
Secondary Filter Width........................................................................................................................... 370mm
Secondary Filter Thickness...................................................................................................................... 22mm
Impeller Information
Impeller Type........................................................................................................................................... Plastic
Impeller Size.............................................................................................................................. 9-3/4 x 6-1/4 in.
Construction
Impeller.................................................................................................................................................... Plastic
Paint Type/Finish....................................................................................................................... Powder Coated
Body........................................................................................................................................................... Steel
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ........................................................................................................ 30 Minutes
ISO 9001 Factory .................................................................................................................................................. Yes
Features:
Remote Control
Three-Stage Filtration
Five Fan Speeds
Hanging Mounts
Primary Filter: 99.97% at 0.3 Microns (MERV-17 HEPA)
Secondary Filter: 10 Microns
Pre-Filter
-10- Model T33150/T33151 (Mfd. Since 03/22)
ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST.
Always discon-
nect machine from power supply BEFORE mak-
ing adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unin-
tended startup or contact with live electrical com-
ponents.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Alerts the user to useful information about proper operation of the
machine to avoid machine damage.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY
Model T33150/T33151 (Mfd. Since 03/22) -11-
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece mate-
rial. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
-12- Model T33150/T33151 (Mfd. Since 03/22)
Additional Safety for Air Filters
Long-term respiratory damage can occur from using this filter to capture hazardous dust
without proper use of a respirator. Collecting flammable or combustible liquids, vapors, or
explosive dusts can cause fire or explosions, resulting in smoke inhalation, serious burns,
or death. An improperly secured air filter can fall, causing head injuries. To reduce the risk of
these hazards, operator and bystanders MUST completely heed hazards and warnings below.
OPERATING LOCATION. DO NOT operate the
air filter in rainy or wet locations—exposure to
water may create a shock hazard or decrease the
life of the machine.
REGULAR CLEANING. To reduce risk of start-
ing a fire, regularly clean surrounding area where
machine is operated. Excessive fine dust buildup
on overhead lights, heaters, electrical panels,
or other heat sources can increase risk of fire.
Regularly check/clean/change filters to avoid fine
dust buildup.
EMPTYING DUST. To reduce exposure to wood
dust when removing dust from filters, which may
increase risk of allergic reactions or respiratory
problems, always turn switch OFF, disconnect
power, and wear a respirator and safety glasses.
To reduce fire and explosion risk, empty dust
away from ignition sources and into an approved
container.
SUSPENDED DUST PARTICLES AND IGNITION
SOURCES. To reduce risk of death or injury
caused by explosions or fires, DO NOT operate fil-
ter in areas where these risks are high, including,
but not limited to, spaces near pilot lights, open
flames, or other ignition sources.
MOUNTING. To reduce risk of injuries due to fil-
ter falling, secure it to load-bearing joists or wall
studs that can support its weight. Do not mount
unit only to sheet rock, pressboard, paneling, or
honeycomb ceiling panels with expansion-type
fasteners, which can easily tear out.
LUNG PROTECTION. Fine dust that is too small
to be caught in filter will be blown into ambient
air during operation. Always wear a NIOSH-
approved respirator during operation and for a
short time after to reduce your risk of permanent
respiratory damage.
INTENDED USE. Using this filter regularly to
collect prohibited materials can result in serious
health problems. It is only designed to capture
dust from ambient air in a woodworking shop for
a short time after cutting or sanding operations.
DO NOT use to collect particles of silica, polyure-
thane, metal, lead paint, asbestos, or hazardous
bacterium. DO NOT allow filter to collect explosive
dusts, flammable or combustible liquids or fumes,
burning or smoking material, or toxic fumes. DO
NOT connect directly to air filtration system. Only
operate with filters installed.
HAZARDOUS DUST. Dust exposure may cause
cancer, birth defects, or long-term respiratory
damage. Be aware of dust hazards associated
with each workpiece material, and always wear
a NIOSH-approved respirator to reduce your risk.
DUST ALLERGIES. Dust from certain woods
may cause an allergic reaction in people and
animals. Make sure you know what type of wood
dust you will be exposed to in case of an allergic
reaction.
POWER DISCONNECT. Turn switch OFF, dis-
connect air filter from power supply, and allow
impeller to come to a complete stop before doing
any cleaning, maintenance, or service.
Model T33150/T33151 (Mfd. Since 03/22) -13-
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
T33150 Full-Load Current Rating ....... 2 Amps
T33151 Full-Load Current Rating .... 2.8 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con-
sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
110V Circuit Requirements
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage .................... 110V, 115V, 120V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
-14- Model T33150/T33151 (Mfd. Since 03/22)
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine.
If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size ...........................18 AWG
Maximum Length (Shorter is Better).......50 ft.
Grounding & Plug Requirements
Figure 4. Typical 5-15 plug and receptacle.
Grounding Pin
Neutral Hot
5-15 PLUG
GROUNDED
5-15 RECEPTACLE
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug provided—if
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!
Model T33150/T33151 (Mfd. Since 03/22) -15-
SECTION 3: SETUP
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Wear safety glasses during
the entire setup process!
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.
If items are damaged
,
please
call us immediately
at (570) 546-9663.
IMPORTANT:
Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-
aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
Unpacking
Description Qty
• Additional Person ....................................... 1
• Safety Glasses (for each person) ............... 1
• Phillips Head Screwdriver #2 ..................... 1
• Open-End Wrench 10mm ........................... 1
• Mounting Hardware .................... As Needed
• Ladder ........................................................ 1
Needed for Setup
The following items are needed, but not included,
for the setup/assembly of this machine.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Figure 5. T33150 inventory.
A
B
C
D
E
F
Box 1 (Figure 5) Qty
A. Handle ........................................................ 1
B. Remote Control .......................................... 1
C. Eye Bolts 5⁄8", 1⁄4"-20 x 7⁄8" ........................... 4
D. Flange Nuts 1⁄4"-20 ...................................... 4
E. Rubber Feet M6-1 x 20 .............................. 4
F. Phillips Head Screws 1⁄4"-20 x 5⁄8" ............... 2
T33150 Inventory
-16 - Model T33150/T33151 (Mfd. Since 03/22)
Box 1 (Figure 6) Qty
A. Eye Bolts 5⁄8" , 1⁄4"-20 x 7⁄8" ........................... 4
B. Remote Control .......................................... 1
C. Flange Nuts 1⁄4"-20 ...................................... 4
T33151 Inventory
Figure 6. T33151 inventory.
A
B
C
T33150 Assembly
To assemble machine:
1. Install handle using (2) 1⁄4"-20 x 5⁄8" Phillips
head screws (see Figure 7).
Figure 7. Handle installed.
x 2
The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to Needed for Setup and gather
all listed items.
Figure 8. T33150 minimum working clearances.
110V
(Power Connection)
Children and visitors may be
seriously injured if unsuper-
vised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
Site Considerations
Workbench Load
Refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
Some workbenches may require additional rein-
forcement to support the weight of the machine
and workpiece materials.
Consider anticipated workpiece sizes and addi-
tional space needed for auxiliary stands, work
tables, or other machinery when establishing a
location for this machine in the shop. Below is
the minimum amount of space needed for the
machine.
Placement Location
211⁄2"
171⁄2"
17"
Model T33150/T33151 (Mfd. Since 03/22) -17-
Test Run
Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The
Troubleshooting
table in the
SERVICE section of this manual can help.
The Test Run consists of verifying the following:
1) The motor powers up and runs correctly 2)
remote control functions correctly 3) varying fan
speeds function correctly.
Serious injury or death can result from
using this machine BEFORE understanding
its controls and related safety information.
DO NOT operate, or allow others to operate,
machine until the information is understood.
DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine
may result in malfunction or unexpect-
ed results that can lead to serious injury,
death, or machine/property damage.
6. Cycle machine through all fan speeds
by pressing Fan button on remote (see
Figure 10).
7. Cycle machine through all time settings
by pressing Time button on remote (see
Figure 10).
8. Turn machine OFF using on/off button on
remote.
Congratulations! Test run is complete.
Figure 10. Remote control buttons.
Fan
Button
Time
Button
on/off
Button
5. Press on/off button on remote control (see
Figure 10) to turn machine ON.
Figure 9. Location of on/off button on control
panel.
on/off
Button
To test run machine:
1. Clear all setup tools away from machine.
2. Place machine on stable surface such as a
workbench able to support it.
3. Connect machine to power supply.
4. Press on/off button on control panel (see
Figure 9) to turn machine ON. Motor should
run smoothly without unusual problems or
noises. Press on/off button on control panel
to turn machine OFF.
Note: Control panel on/off button is only con-
trol feature on panel. All other symbols are
indicator lights that will illuminate when cor-
responding remote buttons are pressed (see
Figure 9).
-18- Model T33150/T33151 (Mfd. Since 03/22)
Site Planning
Figure 11. Good circulation. Air filter placement
promotes circular air motion.
Air
Filter
Figure 12. Poor air circulation. Air filter is placed
too close to the wall so air circulation short
cycles, leaving much of the room unfiltered.
Air
Filter
Site planning is an important step to maximize the
effectiveness of the hanging air filter. Air circula-
tion must be thought out and all obstructions to
the air path considered.
Think of air circulation in terms of the circular
motion of the air before and after the air filter. The
air exiting the filter moves at a higher velocity than
the air entering it. Consequently, exhaust being
vented inside a building can have an effect on the
pattern of air circulation.
Air circulation patterns will vary depending upon
which air flow speed is used and according to
your specific shop setup. Figure 11 shows an
example of good air circulation.
Figure 12 shows an example of poor air circu-
lation, where the air filter is placed too close to
obstructions. In this situation, the velocity of the
air is lost and circulation is diminished.
Below is a list of things to keep in mind when
selecting a spot for the air filter:
• Study your shop layout and try to determine
the best location for the hanging air filter.
Air flow that is obstructed will cause a short
cycle effect, producing unsatisfactory results.
There must be a clearance of at least 3 feet
from any obstructions in front and back of the
unit.
• Try to place the air filter in front of high dust
producers like sanders or near areas where
sanding will take place.
• Do not place the hanging air filter where
garage doors may pass closely or where it
may impede transport or movement of any
other object.
• Try to place the unit where it is easy to access
for turning it on, cleaning and maintenance.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Grizzly Industrial G0777 Owner's manual
-
Grizzly G0888 Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
Easylife Silent Wall Clock Operating instructions
-
Grizzly Industrial G0631 User guide
-
South bend SB1099 Owner's manual
-
South bend SB1100 Owner's manual
-
Grizzly PRO T32336 Owner's manual
-
General International 10-550 M1 User guide
-
MAGIC FX Stage Fan User and Installation Manual
-
Pure n Natural Systems PR20.0 User manual
-
DH Lifelabs CAHP-20WH01 User guide
-
DH Lifelabs CAHP-20WC01 User guide
