Sonel MPI-520 User manual

Brand: Sonel

Model: MPI-520

Category: Measuring, testing & control

Type: User manual

This manual is also suitable for

MPI-520 Start

USER MANUAL

METER FOR ELECTRICAL

INSTALLATION PARAMETERS

MPI-520

SONEL S. A.

Wokulskiego 11

58-100 Świdnica

Poland

Version 3.9.1 11.03.2022

MPI-520 – USER MANUAL

The MPI-520 meter is a modern, easy and safe in use measuring device. Please acquaint yourself with

the present manual in order to avoid measuring errors and prevent possible problems related to opera-

tion of the meter.

MPI-520 – USER MANUAL

CONTENTS

1 Safety ................................................................................................................ 5

2 Menu .................................................................................................................. 6

2.1 Wireless transmission .............................................................................................. 6

2.2 Settings of measurements ........................................................................................ 7

2.2.1 Network voltage and frequency ......................................................................................... 7

2.2.2 Main result of short circuit loop impedance measurement ................................................. 8

2.2.3 Measurement settings ....................................................................................................... 8

2.2.4 Cell autoincrementing ....................................................................................................... 8

2.3 Settings of the meter ................................................................................................ 9

2.3.1 LCD contrast ..................................................................................................................... 9

2.3.2 LCD backlight .................................................................................................................. 10

2.3.3 Auto-OFF settings ........................................................................................................... 10

2.3.4 Date and time .................................................................................................................. 10

2.3.5 Factory (default) settings ................................................................................................. 11

2.3.6 Program update .............................................................................................................. 11

2.4 Language selection ................................................................................................ 11

2.5 Information about manufacturer ............................................................................. 11

3 Measurements ................................................................................................ 12

3.1 Measurement of alternating voltage and frequency ............................................... 12

3.2 Checking correctness of PE (protective earth) connections ................................... 12

3.3 Measurement of current, active power, reactive power, apparent power and cosφ

coefficient ............................................................................................................... 13

3.4 Measurement of short circuit loop parameters ....................................................... 14

3.4.1 Measurement of short circuit loop parameters in L-N and L-L circuit ............................... 14

3.4.2 Measurement of short circuit loop parameters in L-PE circuit .......................................... 16

3.4.3 Measurement of short circuit loop impedance in L-PE circuit protected with residual

current device (RCD) ...................................................................................................... 18

3.4.4 Prospective short-circuit current ...................................................................................... 19

3.5 Measurement of resistance-to-earth ...................................................................... 20

3.6 Measurement of RCD parameters ......................................................................... 23

3.6.1 Measurement of RCD disconnection current ................................................................... 23

3.6.2 Measurement of RCD disconnection time ....................................................................... 25

3.6.3 Automatic measurement of RCD parameters .................................................................. 27

3.7 Measurement of insulation resistance .................................................................... 30

3.7.1 Double-lead measurement .............................................................................................. 30

3.7.2 Measurements with AutoISO-1000c adapter ................................................................... 33

3.7.3 Measurements by means of leads with UNI-Schuko outlet plug (WS-03 and WS-04) ...... 34

3.8 Low-voltage measurement of resistance ................................................................ 36

3.8.1 Measurement of resistance of protective conductors and equipotential bonding with ±200

mA current ...................................................................................................................... 36

3.8.2 Measurement of resistance ............................................................................................. 38

3.8.3 Calibration of test leads ................................................................................................... 39

3.9 Checking sequence of phases ............................................................................... 40

4 Memory of measurement result data ........................................................... 42

4.1 Recording measurement result data in the memory ............................................... 42

4.2 Viewing memory data ............................................................................................. 43

MPI-520 – USER MANUAL

4.3 Deleting memory data ............................................................................................ 46

5 Data transmission .......................................................................................... 47

5.1 Computer connection accessories ......................................................................... 47

5.2 Data transmission with USB joint ........................................................................... 47

5.3 Data transmission with OR-1 radio module ............................................................ 47

6 Power supply .................................................................................................. 49

6.1 Monitoring of the power supply voltage .................................................................. 49

6.2 Replacement of batteries (accumulators) ............................................................... 50

6.3 Charging of accumulators ...................................................................................... 50

6.4 General principles regarding using Ni-MH accumulators ....................................... 52

7 Cleaning and maintenance ........................................................................... 52

8 Storage ............................................................................................................ 53

9 Dismantling and utilisation ........................................................................... 53

10 Technical data ................................................................................................ 53

10.1 Basic data .............................................................................................................. 53

10.2 Other technical data ............................................................................................... 60

10.3 Additional data ....................................................................................................... 61

10.3.1 Additional uncertainties according to IEC 61557-2 (RISO) ................................................. 61

10.3.2 Additional uncertainties according to IEC 61557-3 (Z) ..................................................... 61

10.3.3 Additional uncertainties according to IEC 61557-4 (R ±200 mA)...................................... 61

10.3.4 Additional uncertainties according to IEC 61557-5 (RE) ................................................... 62

10.3.5 Additional uncertainties according to IEC 61557-6 (RCD) ............................................... 63

11 Positions of the meter’s cover ..................................................................... 63

12 Manufacturer .................................................................................................. 63

MPI-520 – USER MANUAL

1 Safety

MPI-520 meter is designed for performing check tests of protection against electric shock in mains

systems. The meter is used for making the measurements the results of which determine safety of

electrical installations. Therefore, in order to provide conditions for correct operation and the correctness

of the obtained results, the following recommendations must be observed:

 Before you proceed to operate the meter, acquaint yourself thoroughly with the present manual and

observe the safety regulations and specifications determined by the producer.

 The MPI-520 meter has been designed for the purpose of measurements of earth connection and

equipotential bonding, ground resistivity, as well as clamps current measurements. Any application

that differs from those specified in the present manual may result in a damage to the device and

constitute a source of danger for the user.

 The device must be operated solely by appropriately qualified personnel with relevant certificates to

realise measurements of electric installation. Operation of the meter realised by unauthorised per-

sonnel may result in damage to the device and constitute a source of danger for the user.

 Using this manual does not exclude the need to comply with occupational health and safety regula-

tions and with other relevant fire regulations required during the performance of a particular type of

work. Before starting the work with the device in special environments, e.g. potentially fire-risk/ex-

plosive environment, it is necessary to consult it with the person responsible for health and safety.

 It is unacceptable to operate the following:

 A damaged meter which is completely or partially out of order,

 A meter with damaged test leads insulation,

 A meter stored for an excessive period of time in disadvantageous conditions (e.g. excessive

humidity). If the meter has been transferred from a cool to a warm environment of a high level

of relative humidity, do not realise measurements until the meter has been warmed up to the

ambient temperature (approximately 30 minutes).

 It should be remembered that BAT message appearing on the display indicates that supply voltage

of the meter is too low. This message signals also that the batteries must be replaced or the accu-

mulator charged. Measurements performed by means of the meter whose supply voltage is too low

are burdened with additional errors that are impossible to be estimated by the user. Such measure-

ments must not be relied on in order to state correctness of protection of a network tested.

 Battery spill and damage to the meter may occur if discharged batteries are left in the meter.

 Before measurements may commence, make sure the test leads are connected to the appropriate

measurement sockets.

 Do not operate a meter with an open or incorrectly closed battery (accumulator) compartment or

power it from other sources than those specified in the present manual.

 The RISO inputs of the meter are protected electronically from overload (e.g. due to having been

connected to a live circuit) up to 440V rms for 60 seconds.

 Repairs may be realised solely by an authorised service point.

ATTENTION!

Only accessories for a given device should be used. Use of different accessories can

lead to errors in the test connection and can introduce additional measurement uncer-

tainties.

Attention:

Due to continuous development of the meter’s software, the actual appearance of the

display, in case of some of the functions, may slightly differ from the display presented

in this operating manual.

MPI-520 – USER MANUAL

Note:

An attempt to install drivers in 64-bit Windows 8 may result in displaying "Installation

failed" message.

Cause: Windows 8 by default blocks drivers without a digital signature.

Solution: Disable the driver signature enforcement in Windows.

2 Menu

The Menu is accessible in each position of the rotary switch.

Press MENU push-button.

Select a proper item by means of ,

push-buttons. Enter a selected

option by pressing ENTER.

2.1 Wireless transmission

See chapter 5.3.

MPI-520 – USER MANUAL

2.2 Settings of measurements

Select a proper item by means of ,

push-buttons. Enter a selected

option by pressing ENTER.

2.2.1 Network voltage and frequency

Before measurements a nominal network voltage Un (110/190V, 115/200V, 127/220V, 220/380V,

230/400V or 240/415V) should be selected that is valid in the area where measurements are made. This

voltage value is used for calculating the values of prospective short-circuit current.

Determination of network frequency, that is the source of potential interferences, is necessary in

order to select a proper measuring signal frequency in resistance-to-earth measurements. Only the

measurement conducted with a properly selected frequency of measuring signal will ensure optimum

filtration of interferences. The meter is designed for filtration of interferences that originate from 50 Hz

and 60 Hz networks.

By means of , push-buttons se-

lect a parameter to be changed, by

means of , select network volt-

age and frequency. Confirm a choice

made by means of ENTER push-but-

ton.

MPI-520 – USER MANUAL

2.2.2 Main result of short circuit loop impedance measurement

By means of , push-buttons se-

lect main result in the form of imped-

ance ZS or prospective short-circuit

current IK; confirm a choice made by

means of ENTER push-button.

2.2.3 Measurement settings

The setting enables activation/deactivation of the field displaying measurement settings. Show or

hide the field with measurement settings by means of and push-buttons, press ENTER push-

button.

2.2.4 Cell autoincrementing

MPI-520 – USER MANUAL

By means of , push-buttons se-

lect the option of automatic incre-

menting of field number after its stor-

ing in the memory or the manual in-

crementing option (automatic incre-

menting is deactivated); confirm a

choice made by means of ENTER

push-button.

2.3 Settings of the meter

Select a suitable item by means of

, push-buttons; enter the edition of

a selected option by means of

ENTER push-button.

2.3.1 LCD contrast

Select contrast value by means of

, push-buttons; confirm a choice

made by means of ENTER push-but-

ton.

MPI-520 – USER MANUAL

2.3.2 LCD backlight

Use the and buttons to se-

lect the backlight off (with the

button) or time to Auto-off. Press

ENTER to validate.

2.3.3 Auto-OFF settings

The setting defines time till automatic shutdown of idle meter.

Set the time or deactivate Auto-OFF

by means of , push-buttons;

confirm a choice made by means of

ENTER push-button.

2.3.4 Date and time

By means of , push-buttons select the value to be changed (day, month, year, hour, minute).

Set a required value by means of , push-buttons. When required settings are made, press ENTER

push-button.

MPI-520 – USER MANUAL

2.3.5 Factory (default) settings

In order to introduce factory (default) settings, highlight YES by means of , push-buttons and

press ENTER push-button.

2.3.6 Program update

ATTENTION!

This function may be used only by the users who are fluent in operation of computer

equipment.

The guarantee does not cover defective operation of the device resulting from wrong use

of this function.

ATTENTION!

A new package of batteries should be installed before programming or the accumulator

should be charged.

During programming the meter must not be switched off as well as the transmission

cable must not be disconnected.

Before updating the program, download the program that is use for programming the meter from the

manufacturer’s website, install this program on your computer and connect the meter to the computer.

Select Software upgrade in the MENU and follow the instructions displayed by the program.

2.4 Language selection

 By means of and push-buttons choose **Language choice** in the main MENU; press

ENTER push-button.

 Select a required language by means of and push-buttons; press ENTER push-button.

2.5 Information about manufacturer

By means of and push-buttons choose Manufacturer info in the main MENU; press ENTER

push-button.

MPI-520 – USER MANUAL

3 Measurements

Remarks:

- A progress bar is displayed during long measurements.

- The content of this chapter should be thoroughly familiarized with since it describes the meter circuits,

the methods of measurements and basic principles concerning interpretation of measurement results.

- Result of the latest measurement is remembered by the meter until a next measurement is started or

measurement settings are changed or the measuring function is changed by means of the rotary switch

or the meter is switched off. The result of the latest measurement is displayed on the screen for 20

seconds. It can be recalled by pressing ENTER push-button.

WARNING:

During measurements (short circuit loop, RCD), earthed parts and parts accessible in

the electrical installation being tested must not be touched.

WARNING:

During a measurement, switching of the range switch is forbidden because it may dam-

age the meter and pose a threat to the user.

3.1 Measurement of alternating voltage and frequency

The meter measures and displays alternating voltage and frequency of the network in all measuring

functions except RE, RX, R±200mA, RISO-conductor. For

and RISO functions, only voltage is dis-

played. This voltage is measured for the frequencies within the range of 45..65 Hz as True RMS. If a

frequency measured is outside the specified range, a proper message is displayed instead of the fre-

quency value: f<45 Hz or f>65 Hz. Voltage is displayed as the main result only for UL-N,L-L, ZL-N,L-L, UL-PE

ZL-PE and U,I,P,Q,S,f,cosφ functions for Only U mode selected. The test leads should be connected as

for a given measuring function.

3.2 Checking correctness of PE (protective earth) connections

When the meter is connected according to the drawing, touch the touch electrode with a finger and

wait for about 1 second. When voltage if found on PE, the device displays PE! message (error in the

installation; PE lead is connected to the phase lead) and generates a continuous audio signal. This

possibility is available for all measuring functions that apply to residual current devices (RCD) and short

circuit loop.

MPI-520 – USER MANUAL

Remarks:

WARNING:

When phase voltage is detected on PE lead, measurements must be immediately

stopped and a fault in the installation must be removed.

- The person making a measurement must ensure that he/she is standing on a non-insulated floor during

the measurement; otherwise the result of the measurement may be incorrect.

- The threshold value, which triggers the signal of exceeded allowable voltage on PE conduit, is approx-

imately 50 V.

3.3 Measurement of current, active power, reactive power, apparent

power and cosφ coefficient

Set the rotary switch of function se-

lection at U,I,P,Q,S,f,cosφ position.

Press F1 push-button. Select

“U,I,f,cos,P,Q,S” by means

of and push-buttons

and press ENTER push-but-

ton. (If you want to measure

voltage or current only, select

a proper position.)

Assemble the system according to the below drawing.

Read out the re-

sults.

MPI-520 – USER MANUAL

3.4 Measurement of short circuit loop parameters

If there are residual current devices in the network tested, they should be bypassed by

bridging for the period of impedance measurement. However, it should be remembered

that the circuit tested is modified in this way and the results obtained may slightly differ

from the actual results.

Each time after completion of measurements, modifications introduced to the installa-

tion for the period of measurements should be removed and operation of the residual

current device should be checked.

The above remark does not apply to measurements of short circuit loop impedance with

the use of ZL-PE RCD function.

Measurements of fault loop impedance performed downstream of inverters are ineffec-

tive and their results are unreliable. This is due to the instability of internal impedance

in inverter circuits during its operation. The measurements of fault loop impedance

should not be performed directly downstream of inverters.

3.4.1 Measurement of short circuit loop parameters in L-N and L-L circuit

Set the rotary switch of function se-

lection at ZL-N,L-L/UL-N,L-L position.

Press F1 push-button if lead

length L needs to be selected.

Select lead length by means

of and push-buttons

and press ENTER push-but-

ton.

Connect test leads according to the drawing

a) for measurement in L-N circuit or

b) for measurement in L-L circuit

lub

a) b)

MPI-520 – USER MANUAL

The meter is

ready for meas-

urement.

Make measurement by pressing START

push-button

Read out the re-

sult.

The result is displayed on the screen for 20s.

The result can be recalled by pressing ENTER push-button.

Remarks:

- The result can be stored in the memory (see point 4.1).

- When many measurements are made in short time intervals, the meter may emit a large amount of

heat. As a result of this, the housing of the device may become hot. This is a normal phenomenon and

the meter is equipped with the protection against excessive temperature. After approximately 15 con-

secutive measurements of short circuit loop, wait until the instrument cools down. This limitation results

from the high current measurement and multi-functionality of the meter.

- Minimum interval between successive measurements is 5 seconds. This minimum interval requirement

is controlled by the meter. A next measurement can be made only when READY! message appears on

the screen.

MPI-520 – USER MANUAL

Additional information displayed by the meter

READY!

The meter is ready for measurement.

L-N!

UL-N voltage is incorrect for making a measurement.

L-PE!

UL-PE voltage is incorrect for making a measurement.

N-PE!

UN-PE voltage exceeds allowable value of 50V.

Phase connected to N terminal instead of L terminal (for ex-

ample, exchange of L and N in the mains socket.

Temperature exceeded.

Network frequency is outside the range of 45...65 Hz.

Error during meas-

ure

A correct result can not be displayed.

Loop circuit mal-

function!

The meter should be serviced.

No UL-N!

Lack of UL-N voltage before the principal measurement.

U>500 V! and con-

tinuous audio signal

Before measurement, voltage at test terminals exceeds 500

3.4.2 Measurement of short circuit loop parameters in L-PE circuit

Set the rotary switch of function se-

lection at ZL-PE/UL-PE position.

Press F1 push-button if L lead

length needs to be selected.

Select a lead length by

means of and push-

buttons and press ENTER

push-button.

Connect test leads according to one of the drawings.

NL or

MPI-520 – USER MANUAL

Checking effectiveness of protection against electric shock of the meter housing in

case of: a) TN network b) TT network

b) LPE

The meter is

ready for meas-

urement.

Make measurement by pressing START

push-button.

Read out the re-

sult.

The result is displayed on the screen for 20s.

The result can be recalled by pressing ENTER push-button.

Remarks:

- Double lead measurement is possible when a test lead other that the lead with a mains socket is

selected.

- Remaining issues connected with the measurements as well as the messages displayed are the same

as those described for measurements in L-N circuit or L-L circuit.

MPI-520 – USER MANUAL

3.4.3 Measurement of short circuit loop impedance in L-PE circuit protected

with residual current device (RCD)

Set the rotary switch of function se-

lection at ZL-PE RCD position.

Press F1 push-button if L lead

length needs to be selected.

Select a lead length by

means of and push-

buttons and press ENTER

push-button.

Connect test leads according to one of the drawings.

Remarks:

- Maximum measurement time is about 32 seconds. The measurement can be interrupted by pressing

ESC push-button.

- In the electrical installations in which 30 mA - rated residual current devices are used, it may happen

that the sum of leakage currents of the installation and the test current will trigger RCD. In such a situa-

tion, one should try to reduce leakage current of the network being tested (for example, by disconnecting

load points).

- Remaining issues connected with the measurements as well as the messages displayed are the same

as those described for measurements L-PE circuit.

- The function works for residual current devices of nominal current ≥ 30 mA.

Page is loading ...

Sonel MPI-520 User manual

Brand: Sonel

Model: MPI-520

Category: Measuring, testing & control

Type: User manual

This manual is also suitable for

MPI-520 Start

Download PDF

report

Sonel MPI-520 User manual

This manual is also suitable for

Sonel MPI-520 User manual

Related papers

Other documents